Manuals - Import export

The GEMÜ 707 2-piece 2/2-way metal ball valve is manually operated. It has a plastic sleeved lockable hand lever. The seat is made of PTFE. — High flow rates — Low weight — Non-twisting lever — Lockable hand lever — Nominal sizes: DN 8 to 50 — Operating pressure: to 68 bar depending on version and/or operating parameters

The sliding gate manual valve for low temperature type 8056 in reinforced version is used for cryogenic control applications down to 200°C. Media such as hydrogen, nitrogen, oxygen, carbon dioxide, etc. can be shut off safely and can be controlled excellently, even in the low temperature range.

Unique for large products to be sliced, powerful in manual mode The vertical carriage ensures ergonomic, upright operation while providing an optimal view of the slicing result. The core component is a powerful blade drive, optionally with intelligent motor control Emotion®. In addition, the VS12 F can be fitted with Ceraclean® surface which is easy to clean and ensures easy feeding of products to the blade. Particularly suitable as all-rounder for preparation areas, kitchens and cafeterias/canteens for the fresh meat counter

The GEMÜ 601, GEMÜ 612 and GEMÜ 673 2/2-way diaphragm valves have a temperature resistant plastic handwheel and are manually operated. The GEMÜ 602 valve has a stainless steel handwheel and is manually operated. Bonnet and internals are made all of stainless steel. A seal adjuster to increase service life of the diaphragm and an integral optical position indicator are included as standard. —Hermetic separation between medium and operator —Optional flow direction and installation position —Long service life of the diaphragm due to patented seal adjuster (US-Pat. 5 377 956) —Valve body also available in multi-port designs (M-block and T-body) or as tank bottom valve body

This manual labelling solution was developed to apply one or more seal labels to folding boxes in small batches - before fully automatic lines are changed over to the product, the products are already sealed with this device. The seal label can be applied to all closure flaps as required. An ultrasonic fork sensor enables the processing of transparent and non-transparent sealing labels. Label roll-on across corners is clean and accurate. The solution for smaller, decentralized labeling jobs: — suitable for transparent/non-transparent (ultrasonic label sensor) — reliable, handy with handle bar — non-slip stand — easy setup — repeatable application of labels — core diameter: 76 mm — max. outer diameter: 200 mm — max. label width: 80 mm — label winding: outer winding

The MAT model series serves as a mobile terminal for all aspects of aggregation and rework. Aggregation and rework can take place over several levels. The devices are available in the following expansion stages: MAT-C Manual aggregation and rework station (1 level) (boxes – shipping cases) MAT-P Manual aggregation and rework station (1 level) (shipping cases – pallets) MAT-CP Manual aggregation and rework station (2 level) (boxes – shipping cases – pallets)

Manual marking dies in engraved design for marking various materials in mirror writing. After hammering into the materials to be marked, texts are legible accordingly. We produce the manual marking dies in many sizes as well as in dotted low-stress design. Individual logos or symbols as well as multi-digit texts are produced to your data.

Manual marking die sets in engraved design for figures from 0 to 9 or letter sets from A to Z in various fonts according to DIN 1451 – in narrow font, narrow-medium font or broad font, alternatively also individually in Arial, Eurobold, etc. The dies can also be made in dotted low-stress design.

Manual stamping presses for steel, tool and machine engineering for simply labelling of multi-digit texts. For standard stamping presses we offer font sizes of 1 to 10 mm with 11 labelling fields on the wheel circumference. By removing the pin stop, the wheels can be easily rotated, which allows setting the desired combination. The striking cap can also be replaced.

Manual marking type holders with hardened type surface, replaceable striking cap, pint stop and clamp screw. This manual marking type holder allows individual labelling, also with company logos. The font size can be designed variably. No fixed norm exists. We make your type holders according to your data.

For hard castings, we offer manual dies made from sinter metal. Sinter metal dies are characterised by a hardness of 68 to 70 HRC. With these dies, welded or processes hard surfaces can be labelled. Company logos as well as individual numbers and letters can be provided. The maximum font size should not exceed 10 mm.

The sliding gate manual valve type for high temperature type 8053 in reinforced version is suitable for a wide range of process applications up to 530°C. Media such as steam, liquids, gases, etc. can thus be shut off safely and controlled excellently, even in the high temperature range.

The sliding gate manual valve type 8051 in short design is suitable for a wide range of process applications. Media such as steam, liquids, gases, etc. can be shut off safely with low actuating force and can be controlled excellently.

The sliding gate manual valve type 8050 in reinforced design and long construction is suitable for a wide range of process applications. Media such as steam, liquids, gases, etc. can be shut off safely with low actuating force and can be controlled excellently.

The sliding gate manual valve type 8050 in long design with on/off and control operation is suitable for a wide range of process applications. Media such as steam, liquids, gases, etc. can be shut off safely with low actuating force and can be controlled excellently.

Manual cleaning with ultrahigh pressure water jetting technology often places high demands on the staff. Working overhead, in a stooped position, with respiratory protection or in heavy protective suits these and many other requirements can have a negative impact on work efficiency and safety. The WOMA Jetty now makes cleaning work with highpressure water more comfortable, more efficient and safer. This is made possible by a manipulator that is as manoeuvrable as it is robust and can be controlled via remote control. This means a consistently high quality of work even for hardtoreach work areas. Four extendable legs allow an enlarged footprint for outstanding stability in any environment. Depending on the task to be performed, different water tools can be used with the WOMA Jetty.

The Load cell model 8451 has been developed for measuring the forces that occur during press operation. The internal measuring elements have a rugged design, which mean they can cope reliably with the steep force curves that are typical of press applications. They can be fitted or replaced quickly and easily on the press ram without the need for additional components around them. The force sensor is placed between the tool and the press ram and can thus measure the actual compression force directly in the axis of operation. The load cell measures the compression forces between the circular contact surfaces of plunger and tool. The pin on its top side and hole on its lower face are simply provided for mechanical fixing and centering the components correctly. The connecting cables are suitable for drag chains, designed for many movements and stably fastened in the sensor housing.

This exceptionally versatile tool for post-mould assemblies is ideally suited to all levels of production: from a single unit for prototype assembly, to multiple units on an assembly line. The SPIROL® Model CM Manual Compression Limiter Installation Machine easily accommodates quick change-overs by simply: • Replacing the fixture • Swapping insertion punch/pusher tip • Adjusting the positive stop for new install height. The use of high quality shafting and bearings results in smooth operation, precise positioning, repeatability, and durability. The Model CM Manual Compression Limiter Installation Machine installs Compression Limiters ranging in diameter from M3 to M10 metric and #4 to 3/8" unified, and has a maximum insertion force of 0.9kN (200 lbs).

3/2-way NO or NC microvalves with various actuation systems. A variety of mechanical or manual actuators can be combined and expanded to 5/2 and 5/3-way functions using a universal adapter.

Lid Lifter SKH 2000 for easy opening of street caps and hydrant lids. Weight optimized to generate the maximum kinetic energy and thus reduce the strain on the technician. Thanks to the optimal working height, no stooping is necessary. The cap lifter is simply pressed down, no traction is necessary, this design ensures fatigue-free work. When the Lid Lifter SKH 2000 cap lifter has been hooked in, the spring can be tensioned by pressing the cap lifter. When the cap lifter is released, the spring energy is used to open the cap. A suitable mounting-point for vehicles will be delivered as well.

Powerful all-rounder for kitchen and selling - high performance in a small space Ideal for all manual slicing tasks such as cooked ham, boiled and cooked sausages, sliced cheese or long-life goods such as salami and air-dried ham. Operation is particularly easy thanks to a Ceraclean® surface with outstanding gliding properties, technically mature ergonomics and thus absolutely safe for the user. Removable parts are dishwasher safe and can be mounted in a flash. The Ceraclean® surface finish is very easy to clean.

Miniature ball valves and universal ball valves in brass, with 1/8 to 2″ thread or plug-in connection for hose 4 to 8 mm.

Manual slide valves as real shut-off valves, which allow the system to be vented when it is switched off. Available in sizes 1/8 to 1/2″. Other colors such as black or red, as well as special versions with spring return or latching are available on request.

Powerful and flexible in manual operation specially for large products, even with bones such as air-dried ham. The vertical carriage ensures ergonomic, upright operation while providing an optimal view of the slicing result. The robust product holder and smooth carriage ensure risk-free slicing within the standardized design requirements. The core component is a powerful blade drive, optionally with intelligent motor control Emotion®.

The manual premium vertical slicer sets worldwide standards in terms of ergonomics, hygiene and safety. It stands out due to its wealth of variants. Individual and powerful slicer for a variety of products to be sliced in manual mode. The vertical carriage ensures ergonomic, upright operation while providing an optimal view of the slicing result. The core component is a powerful blade drive, optionally with intelligent motor control Emotion®. In addition, the VS12 can be fitted with a Ceraclean® surface which is easy to clean and ensures easy product feeding to the blade.

This manual vertical slicer offers you a unique high-end performance package. Simplify your processes with the intelligent support SmarterSlicing: The digital display will automatically indicate you when it's time to clean, sharpen or maintain the VSP. Your benefits: You ensure high quality of your products and optimize your processes. Area of Use Particularly suitable as all-rounder for kitchens and cafeterias/canteens Sales counter

HP-60-CK - manual hydraulic crimping tool, 62 kN, CU300mm² for exchangeable dies series "60-CK", "22" Two stroke hydraulic system for fast forward Characteristics turnable crimping head automatic pressure reliefe Manual return is possible in each position working pressure: 700 bar (70 MPa) optional: transport case NEW! HP-131 with mechanical piston protection. ==> Piston will not be demaged by using without dies.

The AQUACHEM LCM 320 (pocket press membrane) is ideal for mobile deployment on site on a suitable trolley and can be operated with up to 15 bar loading and 15 bar membrane squeezing. This machine can also be used as a testing filter press in the case in order to decide on the right fabric or to check the filterability of the suspension. Fully equipped, this compact press can manually implement functions that our fully automatic machines can do. The AQUACHEM LC 320 (pocket press chamber) is identical in design to the LCM 320 and differs only in its function as a chamber filter press (without membrane). The LC 470 is the more affordable, low-cost version of the EC-series. Main feature is the restriction of the feeding pressure to 7 bar. All other features are the same as the EC-series. This series is built in a compact design with a feeding pump and discharge manifold.

In the tried-and-tested, gasketed design, the EC-series offers many benefits to the user on top of its ease of operation. Due to the internal drainage, use in even the most hygienically clean areas is possible. The press lock is performed by an automatically self-regulating pneumatic/hydraulic closing system. The automatic closing pressure maintenance ensures that the plate pack always remains closed. An adjustable pressure switch with a potential-free contact is provided for integration into the customer's control system. This prevents the feeding pump from running uncontrollably. Also, as with all AQUACHEM filter presses, the discharge manifold can be generated here at the customer's request. Due to the gasketed design, the seamless backflushing of the filter media in the filter press is possible. The filter press frame is phosphated and powder-coated, offering a high level of protection against external influences.