ball pins Germany

... engineering igubal® double spherical bearing WDGM igubal® variable double spherical bearing igubal® double spherical bearing WDGM igubal® removable angle joints Easy assembly and disassembly of the ball pins by defined forces igubal® removable angle joints not removable igubal® coupling bars configurator - not removable One side removable igubal® coupling bars configurator - removable from...

...Our ball pins have diameters ranging from 5 to 20 mm and are particularly well-suited for flaps and chassis. From machined to cold-formed + machined, to completely cold-formed components, we offer everything according to your wishes and requirements. For special inquiries, we are happy to assist you! 5 to 20 mm: machined for flaps and chassis: cold-formed + machined...

...Note Angular joints DIN 71802 consist of ball sockets DIN 71805 and ball pins DIN 71803. The swivel angle is 15° for the version with safety clip (type CS, BS) and 18° for the version without safety clip (type C, B). During assembly, the ball pin is pressed in by the retaining ring and held in place by it. If the holding force (see also minimum release forces in the table) is not sufficient, the...

...SUTTY Dimensions (L x W x H): 1200 x 600 x 135 mm Delivery includes 1x Ball transfer table 6x Long stop rails (freely positionable) 4x Short stop rails (freely positionable) 1x Set of pins for tilt protection SUTTY XL Dimensions (L x W x H): 1200 x 800 x 135 mm Delivery includes 1x Ball transfer table 6x Long stop rails (freely positionable) 1x Set of pins for tilt protection Load capacity for...

...Spring-loaded pressure pieces are used for locking as well as for push and pull pins. Execution: Steel strength class 10.9 (blackened) or stainless steel; ball hardened, bright. Spring-loaded pressure pieces with pins (with internal hexagon) Execution: Steel strength class 10.9 (blackened) or stainless steel; ball hardened, bright. Spring-loaded pressure pieces are used for locking as well as for push and pull pins. The slot on the pressure pin side is used for screwing into blind holes. Pressure pieces with thread locking available upon request.

... obtainable strengths. Metering rods Ejector pins Fittings Ball bearings/Overrunning clutches >> Current alloy surcharges >> Current scarp surcharges VERSIONS AND FORMS SUPPLIED Drawing From 2.0 mm to 28.0 mm round, tolerance zone IT 9 Min. bar length 2,000 mm Max. bar length 5,000 mm (2.0 mm to 6.0 mm round) Max. bar length 7,000 mm (6.0 mm to 16.0 mm round) Max. bar length 9,000 mm (> 16.0 mm round and on request) Length tolerance ± 25.0 mm Grinding From 0.5 mm to 32.0 mm round, tolerance zone IT 6 (Rm up to 1,600 N/mm² for bright steel for standard parts) > 32.0 mm to 60.0 mm...

... on request:Zinc-plated rail and runner (Rollon Alloy); increased anticorrosion protection on request Rail material:C43 Slider body material:Fe360 Roller material:100Cr6 Roller pins lubricated for life:Roller pins lubricated for life...

...We manufacture single-sided and double-sided gauges/test pins according to customer specifications.

...Attachment option for holding cable. Maximum temperature range +250 °C. Shear force double shear (F) = S · τ aB max. Accessories: Safety spiral cable 03199-10200 Holding cables with loop 03199-.... Key ring 03199-15/19/23 Socket for ball locking pins 03197.... Order number: 03194-2305*** D: 25 D1: 5 D2: 5.5 D3: 14 L: 10/15/20/25/30 L1: 6 L2: 26.5 Receiving hole H11: 5 Maximum shear force double shear kN: 15...

... aggressive substances, the ball lock pin is made entirely of stainless steel. Standard parts from KIPP exhibit high manufacturing quality and operate reliably and safely even after frequent use. The ball lock pins are produced directly at HEINRICH KIPP WERK and adhere to the traditionally high quality standards of all KIPP products.

... Good plastic and elastomer compatibility Excellent temperature resistance Lowest evaporation losses, also at high temperatures ensure long regreasing intervals Good media resistance Also suitable for fast-runing bearings thanks to low share of solid lubricants Operating temperature:-20 °C → +300 °C NLGI grade:2 DN factor (dm x n):350,000 mm/min Base oil viscosity (40 °C):440 mm²/s Four-ball test rig (welding load):4,800 N...

... flag design, the separated areas can be color-enameled and additionally printed. There is ample space on the back for laser engraving for advertising purposes. In the third design variant, full-area advertising on the front is also possible, including with a photographic motif. Delivery includes a shopping cart token in ball design on the front or according to individual customer wishes. The back is...

... Features Curve rollers consist of hardened, precision-ground inner and outer ring raceways. They are available in full-roller design or with separate (cage-guided) needle, ball, tapered, or cylindrical rolling elements. They are ready-to-install and cost-effective bearing solutions. The integrated roller pin with thread allows for relatively easy assembly to the connecting structure. Curve rollers are available with or without pins in a variety of designs for a wide range of applications and diverse operating conditions.

... and long-term stability. The rod is guided in a low-play floating frontal bearing. This absorbs small angular and parallel displacements. Principle:Potentiometric Measuring range:0 … 900 mm Signal output:Depending on excitation voltage Protection class:IP60, IP65, IP67 Range of operating temperature:-30 ... +100 °C Supply voltage:Max. 50 VDC Electrical connection:5 pins plug connection, Integrated connection cable 1 m Return spring:No...

...{"Material":"Support cable made of stainless steel.\nClamp and crimp terminal made of aluminum.\n\nExecution:\nSupport cable with plastic coating.\n\nNote:\nWith the support cable and key ring B0090, the ball lock pins B0068, B0070, as well as the plug pins B0086 can be secured against loss. A screw M5 is used to attach the support cable.\nOperating temperature: +80 °C.\n\nSupport cable: Stainless steel\nForm A: With eyelet and crimp terminal\nForm B: Both sides with crimp terminal\nForm C: Both sides with eyelet"}...

... torque is exceeded (overload condition), the coupling disengages. During disengagement, the pins in the overload elements perform an axial movement (stroke) and remain in the disengaged position. Following masses can run free. Re-engagement is done manually.

... units give a smooth and light transfer from/to the dollies, whilst the addition of pneumatically driven pads and stop pins ensure the ULD is safely held in position for loading and unloading. Benefits: Supports peak flow efficiently and reliably Reduces stress and injury at the workplace ...

... achieve. The corresponding centric and eccentric pins are available upon request. Advantages and features of the running rollers • Quiet operation • High speeds possible • Low starting and running torques • System integration possible • Centric and eccentric pins available...

...The combination of a reinforced outer ring, needle cages, and solid roller pins allows for use under high radial loads. Available in stainless steel upon request. The combination of a reinforced outer ring (with or without a profiled surface), needle cages (also available as fully needle or fully roller cam rollers), and solid roller pins enables use under high radial loads. For applications...

...Various designs (set): for right-angled connection or at 45° angle of 2 round tubes — with/without anti-twist device for right-angled connection of a round tube profile with an aluminium profile — independent of the groove — Groove 8 or 10 for ball but connection of 2 round tubes intersecting connection of 2 round tube profiles parallel connection of 2 round tube profiles or to an aluminium profile Translated with www.DeepL.com/Translator (free version)...

...). Toolles assembly of the spindle extension with a stainless steel clip pin. Connection pins made of stainless steel 1.4301. Transport security of the rod minimum of 150N. Self-locking in every adjustable position through a PE sealing collar on the steel tube. Torques accord. to GW336. Three-piece PE protection tube system with an additional corrugated protection tube, bonded centring cap and universal round bell accord. to GW336. Completely dirt-proof and water-repellent. Incl.: Integrated position indicator „1/4 turns“.

...For machine components such as ball valve adapters, pins, and reducing fittings, every hundredth of a millimeter counts. State-of-the-art technologies like CNC milling and precise finishing processes such as grinding, polishing, hardening, coating, etc., ensure the highest manufacturing quality that our customers can rely on 100 percent.

...Roller bearings are ball bearings with thick-walled outer rings, suitable for high and shock loads. These bearings can accommodate both high radial forces and axial forces in both directions. The outer ring can be either cylindrical or spherical (reducing edge stress in case of alignment errors). Type designations: LR.. / LFR.. KLR.. (With plastic sleeves) ZL.. / ZLE.. (With roller pins = pin roller bearings)...

...Ball bushing guides, lead screws, carriages, support rails, rollers, pins, lubrication and cover flaps, cover strips, lubrication and wiper units, groove covers, linear bearing units and linear sliding bearing units, linear ball bearings, ball bushing guides, shafts and support rails, shaft supports, ball bushings, steel shafts, shaft supports, accessories for ball bushing guides, rolled lead...

...- 8 maintenance-free ball bearings - Lubricatable joint pins - Removable safety approach plate at the front - Loading ramp for attachment to the platform plate Load capacity: 350 kg Size: 220 x 60 cm Max lift height: 96 cm Loading height: 18 cm Drive: Foot pump hydraulic with 1 m hose Country of origin: Germany...

... bow chains can be supplied with special lubricants or special coatings on request • We supply side bow chains with attachments such as bent attachment plates or extended pins on request • All ELITE chain plates 1 are tapered and shot-blasted; production processes such as fine blanking and ball-drifting ensure a particularly high contact ratio • Seamless, cold-extruded, shot-blasted rollers 2 with extremely regular wall thickness • Reduced pin diameter 3 enables sideflexing (curved running)...

...Hinges, double hinges, ISO blind nuts, folder rivets, extension discs for folder rivets, screw rivets, drift pins, pointed staples, blind rivets, screw blind rivets, panel fasteners, Tree-Lok pins, Tree-Lok sockets, hex nuts, threaded pieces, hex screws, hex caps, thread protection sleeves, decorative caps, vent plugs, glass pads, elastic buffers, universal buffers, felts, anti-slip pads, covers for drill holes, ball knobs, protective corners, threaded plugs, adjustable gliders.

...The ball-bearing transport rollers TR50 with a D50 aluminum tube can be removed from an existing structure using spring-loaded fastening pins. They can also be installed and screwed into an existing structure. Material: PA-GF Color/Surface: black Weight: 0.25 kg...

... includes various solid carbide (VHM) cutters and CBN or diamond grinding pins. The VHM cutters are available for processing different bevel angles and radii. When contour machining with the VHM cutters, ball bearings with diameters of Ø3, Ø4, Ø5, or Ø6mm are used. In non-ferrous metals and steels, a bevel width of up to 3mm is possible, and in stainless steels, up to 2mm. Radius machining is feasible up to R3. You can find the technical specifications for both machines in the .pdf file. KKE 1:22129 KKE 2:29642...

...Polishing steel balls, polishing steel pins, and satellites made from stainless steels, as well as blasting media for polishing processes and surface technology. 3.175 mm: Ball 3.175 mm/G1000/1.4301...