Manuals - Import export

ABS housing, in 1½2" and 2" connection, Optional with or without piping sets for all well-known filter brands, 3.5 bar

The GEMÜ 707 2-piece 2/2-way metal ball valve is manually operated. It has a plastic sleeved lockable hand lever. The seat is made of PTFE. — High flow rates — Low weight — Non-twisting lever — Lockable hand lever — Nominal sizes: DN 8 to 50 — Operating pressure: to 68 bar depending on version and/or operating parameters

The Tape Factory stands out in performance and so will the selection of materials. Allowing just the right amount tack to hold the flower sleeve yet be easy to open, its adhesive will not dissolve in water, and the tape stays transparent. With its width of 19 mm, it’s less likely to constrict the stems compared to other binding methods. No need for scissors or knives. It’s easy to remove and can go directly into a vase.The paper tabs create a handle to open the tape closure easily. Both provide a timesaving, user-friendly solution which maintains the quality of the flower without pinching the stems.

Body, flange, screw and shaft: stainless steel Couplings: stainless steel (nylon as an option with code -A) Membrane and valves: made of a hydrocarbon-resistant elastomer (Neoprene as an option with code -A) Lever: zinc-plated steel with a rubber handle, 1 metre in length

Body: cast iron Mechanism: brass Waterproofing: by nitrile O-ring. NBR flange O-ring

Body, cover and lever: cast iron Inner mechanism: brass Waterproofing: nitrile O-ring Seal: nitrile O-ring, NBR flange O-ring.

Body, cover and lever: cast iron Inner mechanism: brass Waterproofing: graphite braid NBR flange O-ring, Viton® or PTFE seal as optional.

Body: cast iron Mechanism: zamak Waterproofing: by nitrile O-ring (not suitable for water)

Body, cover and lever: cast iron Inner mechanism: brass Braid: PTFE Seal: flange O-ring made of Viton®. Optional PTFE seal (FAT_-PTFE)

Body, cover and lever: cast iron Inner mechanism: brass Braid: PTFE Suction: 3/4'' stainless steel pipe with 2” bung Seal: flange O-ring made of Viton®. Optional PTFE seal (FAT_-PTFE) Discharge pipe: stainless steel elbow fitting, 2 m NBR hose (conductor) fluid temperature <80°C Fitting: brass half-shells Manual delivery gun (version FAT ), automatic delivery gun (version FAT_A)

Lindemann Manual Gear Box Treatment has been specially developed to smooth the shifting of a gearbox, differential and / or swingarm while reducing noise. The unique P.T.F.E based formula reduces friction by more than 50%, resulting in more efficient operation and therefore less fuel consumption! In addition, the shifting will feel smoother.

Valves are generally used to control the product flow under flat-bottom silos with tunnel systems, chain conveyors and conical-bottom silos. It has a wide application area with its galvanized steel structure.

The part washing machine is designed to easily clean dirty parts with a small size and complex structure in the shortest time possible. Thanks to its brush, the person performing the washing process can carry out any kind of cleaning in the dirty part in detail. It is an ideal parts washing machine for using in small areas.

The sliding gate manual valve for low temperature type 8056 in reinforced version is used for cryogenic control applications down to 200°C. Media such as hydrogen, nitrogen, oxygen, carbon dioxide, etc. can be shut off safely and can be controlled excellently, even in the low temperature range.

Unique for large products to be sliced, powerful in manual mode The vertical carriage ensures ergonomic, upright operation while providing an optimal view of the slicing result. The core component is a powerful blade drive, optionally with intelligent motor control Emotion®. In addition, the VS12 F can be fitted with Ceraclean® surface which is easy to clean and ensures easy feeding of products to the blade. Particularly suitable as all-rounder for preparation areas, kitchens and cafeterias/canteens for the fresh meat counter

MANUAL CLIPPER FP HR 45M FOR GABIONS Large sturdy manual clipper with ring closure, using clips of 45 mm. with wire diameter 3 mm. and can close up to a diameter of 15 mm. Suitable for the assembly of the containment gabions in mesh, structures and fencing in wire mesh, fixing reinforcements for the building, sealing bags or mattresses that are used as retaining walls, sound barriers, dikes, road reinforcements, reinforcement of banks, horticulture, traps and rockfall protections.

MMANUAL LIFTER FOR PALLETS MOD. FPSDJ 1500 - shipped fully assembled! Pallet lifter with hydraulic foot pump and rudder (for low weight can use the pedal), steel frame with fork tip rounded, directional nylon wheels with brakes and double rollers, fixed width forks. The model FP SDJ 1500 is equipped with double chain for lifting. WARNING: all the elevators are shipped pre-assembled, tested one by one before packing in a professional manner and with CE certification. The elevators FPSDJ are very practical and robust, recommended where the paving is smooth (eg warehouses) where the occasional and not continuous lifting of pallets does not justify the purchase of a battery model. The structure and operation are similar to those of a standard pallet truck. You can lift the load both through rudder or pedal. For each pumping the forks are raised about 3 cm. The descent is done by pressing the lever on the rudder. And it is controlled and at a safety speed.

MANUAL LIFTER FOR PALLETS MOD. FPSDJ 1016 - shipped fully assembled! Pallet lifter with hydraulic foot pump and rudder (for low weight can use the pedal), steel frame with fork tip rounded, directional nylon wheels with brakes and double rollers, fixed width forks. WARNING: all the elevators are shipped pre-assembled, tested one by one before packing in a professional manner and with CE certification. The elevators FPSDJ are very practical and robust, recommended where the paving is smooth (eg warehouses) where the occasional and not continuous lifting of pallets does not justify the purchase of a battery model. The structure and operation are similar to those of a standard pallet truck. You can lift the load both through rudder or pedal. For each pumping the forks are raised about 3 cm. The descent is done by pressing the lever on the rudder. And it is controlled and at a safety speed.

MANUAL LIFTER FOR PALLETS MOD. FPSDJ 1012 - shipped fully assembled! Pallet lifter with hydraulic foot pump and rudder (for low weight can use the pedal), steel frame with fork tip rounded, directional nylon wheels with brakes and double rollers, fixed width forks. WARNING: all the elevators are shipped pre-assembled, tested one by one before packing in a professional manner and with CE certification. The elevators FPSDJ are very practical and robust, recommended where the paving is smooth (eg warehouses) where the occasional and not continuous lifting of pallets does not justify the purchase of a battery model. The structure and operation are similar to those of a standard pallet truck. You can lift the load both through rudder or pedal. For each pumping the forks are raised about 3 cm. The descent is done by pressing the lever on the rudder. And it is controlled and at a safety speed.

MANUAL LIFTER FOR PALLETS MOD. FPSDJ 1010 - shipped fully assembled! Pallet lifter with hydraulic foot pump and rudder ( for low weight can use the pedal), steel frame with fork tip rounded, directional nylon wheels with brakes and double rollers, fixed width forks. WARNING: all the elevators are shipped pre-assembled, tested one by one before packing in a professional manner and with CE certification.

ME SERIES HI - single bar 5 mm. (suitable for medium thick envelopes in PE, polypropylene, coupled light) Welders Series ME HI 5 mm with closure lever, allowing the sealing of heat sealable plastic bags with thickness up to 0.40 mm total. The models ME HC 5 mm are equipped with cutter for trimming of the envelope. This system allows you to pack products with different lengths and then performing the trimming of the bag, leaving no protruding edges and unsightly. The sealers ME HC are available in sizes 300, 400 and 500 mm. This series of sealers makes a sealing of 5 mm, very beautiful and suitable for food bags or if you want a more valid and robust sealing than the standard 2 mm. This sealers have a impulse sealing (resistance heats for a few seconds) and a timer for adjusting the sealing time. The sealing cycle is indicated by an indicator light. With manual sealing bar, sealing width 5 mm., Maximum thickness of 0.20 mm weldable. (mm. 0.40 total).

Impulse manual bag sealers machines FPS series are the simplest and most economical series of sealers machines. The model FPS-C is equipped with a cutter for trimming the envelope. This system allows you to pack products with different lengths and then performing the trimming of the bag, leaving no protruding edges and unsightly. This model is only available in sizes 300 and 400 mm. The sealers FPS/FPS-C are suited to a medium-low production and allow the closing of plastic bags without folding, with maximum thickness of 0.15 mm (0.30 mm total). The sealing is by impulse (the resistance heats for a few seconds) and can be adjusted by timer. The sealing cycle is generally 3 seconds and is indicated by an indicator light. These sealers has a sealing width of 2 mm.

MANUAL NUMERICAL AND ALPHANUMERIC PRICING MACHINES FP-PRZ2 SERIES with 1 or 2 PRINT LINES FOR LABELS 26x16 mm rectangular and wave shape The manual pricing machines are suitable for printing prices, dates, lots, deadlines and codes on adhesive labels. They are particularly suitable for use in the food sector, where it is necessary to specify batches and expirations of the products and wherever it is necessary to label. The pricing machines produce numerical or alphanumeric writings on one or two printing lines and depending on the model the printable characters can be from 8 to 10 per line. The 26x16 labels are available in wave and rectangular format. The most used are white, however it is also possible to request other colors and pre-printed. The printing lines of the pricing machines can be: - numeric: all numbers with dashes and currency symbols (£/€/$). - alphanumeric: all numbers and letters WITHOUT currency symbols.

MANUAL NUMERICAL AND ALPHANUMERIC PRICING MACHINES FP-PRZ SERIES WITH 1 PRINT LINE FOR LABELS 26x12 mm wave The manual pricing machines are suitable for printing prices, dates, lots, deadlines and codes on adhesive labels. They are particularly suitable for use in the food sector, where it is necessary to specify batches and expirations of the products and wherever it is necessary to label. The pricing machines produce numerical or alphanumeric writings on a print line and depending on the model the printable characters can be 8 or 10. The 26x12 labels are available only in wave form and the most used are white, however it is also possible to request other colors and pre-printed. The characters of the pricing machines can be: - numeric: all numbers with dashes and currency symbols (£/€/$). - alphanumeric: all numbers and letters WITHOUT currency symbols

MANUAL TRACTION LIFTER WITH BATTERY LIFTING SERIES FPTX SEMI-E - shipped fully assembled! The price shown includes 1 battery 12V or 24V and high-frequency charger Practical, handy and high quality forklift. The forklifts FPTX series are featured with manual advancement and electric lifting. Their great stability is suitable for lifting very heavy loads safely. The version FPTX 12 is equipped with the standard polyurethane wheels, for maximum smoothness even with higher loads and 24 Volt batteries. Operating conditions 0-40 °C Degree of electrical protection IP 20 Available in the following versions: FPTX 1009 max. load 1000 kg, lift height 810 mm FPTX 1016 max. load 1000 kg, lift height 1510 mm FPTX 1020 max. load 1000 kg, lift height 1910 mm FPTX 1225 max. load 1200 kg, lift height 2410 mm FPTX 1229 max. load 1200 kg, lift height 2810 mm FPTX 1235 max. load 1200 kg, lift height 3410 mm

MANUAL LIFTER FOR PALLETS MOD. FPSDJ 1030 - shipped fully assembled! Pallet lifter with hydraulic foot pump and rudder (for low weight can use the pedal), steel frame with fork tip rounded, directional nylon wheels with brakes and double rollers, fixed width forks. The telescopic structure of the elevator, thanks to the minimum height of the mast of 2080 mm, it allows to pass under the majority of doors and openings. The lifter height of 2080 mm also keeps raising the load to a height of about 15-20 cm.Over 20 cm of lifting, the structure begins to slip and the height of the trolley increases to reach 3.5 meters when the load is raised to 3 meters. WARNING: all the elevators are shipped pre-assembled, tested one by one before packing in a professional manner and with CE certification.

Restores, softens and protects your very dry and irritated hands faster. Restorative and antibacterial components. Without perfume. The creamy and nourishing texture can easily be smoothed out. The transparent cream absorbs quickly and forms an insulating barrier over the skin. Thanks to this "second-skin effect" your hands are protected.