Vibration sensors - Import export

The sensor system is intended as a component for use e.g. in wind power plants to measure and evaluate vibrations in the mast head. Registration of dynamic accelerations by means of MEMS sensors (Micro-Electro-Mechanical System) with subsequent digitisation by a controller. The device consists of an acceleration sensor, a controller unit and three types of output interface. The main feature is two safety switching contacts (potential-free), which can be used e.g. in the safety chain to undertake safety shut-off in the event of excessively high acceleration values. Data output is carried out via the CANopen interface. The standard or the safety profile can be selected. There are additionally two analogue outputs 4 ... 20 mA, which can be optionally assigned to two of the three measurement axes. Thanks to its high resistance to vibration and shock, the sensor is suitable for use in areas with rough environmental conditions.

The sensor system is intended as a component for use e.g. in wind power plants to measure and evaluate vibrations in the mast head. Registration of dynamic accelerations by means of MEMS sensors (Micro-Electro-Mechanical System) with subsequent digitisation by a controller.The device consists of an acceleration sensor, a controller unit and the output interface PROFIsafe over PROFINET for output of the acceleration values. Thanks to its high resistance to vibration and shock - more than the defined measuring range -, the sensor is suitable for use in areas with rough environmental conditions.Electrical connection is carried out using three connectors.

The sensor system is intended as a component for use e.g. in wind power plants to measure and evaluate vibrations in the mast head. Registration of dynamic accelerations by means of MEMS sensors (Micro-Electro-Mechanical System) with subsequent digitisation by a controller. The device consists of an acceleration sensors, a controller unit and three types of output interface. Data output is carried out via two analogue interfaces with 4 ... 20 mA plus CANopen and via 4 relay contacts (currently 1 error relay contact). The NVA is parameterised via the CANopen interface. This is not galvanically separated. The sensor is equipped with a filter circuit to protect against fast transients and surge voltages of up to 2 kV in the supply. The protection types are IP 69K (housing) and IP 67 (connector/socket). With its good vibration and shock values, the sensor is suitable for use in areas with rough environmental conditions.

A micro-electromechanical spring-mass-system is continuously measuring the acceleration and transforms the measured data into an analog 4-20mA output signal. The sensor complies with the standards of DIN EN 50155 for railway vehicles. It is espacially intended to be used in the on-board network of rail vehicles. Its extrem rugged housing enables applications in harsh conditions in the outskirt area of the vehicle, directly at the bogie. The sensor impresses by its high ruggedness against impact, dust as well as moisture and guarantees high reliability. The device detects accelerations in a measuring range of ± 4g and operates with 24 Volt supply voltage.

A micro-electromechanical spring-mass-system is continuously measuring the acceleration and transforms the measured data into an analog 4-20mA output signal. The sensor complies with the standards of DIN EN 50155 for railway vehicles. It is espacially intended to be used in the on-board network of rail vehicles. Its extrem rugged housing enables applications in harsh conditions in the outskirt area of the vehicle, directly at the bogie. The sensor impresses by its high ruggedness against impact, dust as well as moisture and guarantees high reliability. The device detects accelerations in a measuring range of ± 4g and operates with 110 Volt supply voltage.

This sensor for measuring exhaust gases was developed together with a Formula 1 team. The goal was to achieve the greatest possible reliability during the race. The sensor was designed so that it can withstand a maximum of vibrations and extreme temperatures while being made in a highly compact construction at the same time. The special feature is the connection lead. It is not made from the usual mineral-insulated stainless steel sheathed line, which is too rigid and which tends to vibration fractures. Instead, the line is made of stranded conductors with PTFE insulation and an additional heat shield so it can be easily and flexibly adapted to the environment. The sensor is being used with exceeding success by professional teams in long distance races, American race series and the domestic DTM. The benefits: Highly vibration-proof Very robust High temperature resistance (up to 1,200 °C) Individual plug assembly possible Can be individually adapted

This plug-in sheathing thermocouple is recommended for measuring the temperature in the exhaust gas flow. It is genuinely multipurpose, mounting with the cap nut means the thermocouple does not need to be rotated, which simplifies installation and fast replacement. In addition, it has “motor sports genes” such as vibration resistance, fast response time and high temperature resistance. The benefits: Vibration-proof Fast response time High temperature resistance (up to 1,200 °C) Various installation lengths can be supplied With cap nut Sheathed thermocouple NiCr-Ni, Type “K”, Class 1

GMN high-performance spindles with an integrated motor are designed for those applications and relevant installation situations in close collaboration with our customers. They are available as needed with a synchronous or asynchronous motor, for manual - HGS series - or automatic tool change - HGC, HGT series - and with oil-air or grease lubrication. Additional options are, for example, an AE sensor, vibration sensor or an automatic balancing system.

Inductive displacement sensors of this series measure linear displacements and indirectly all mechanical values convertible into displacements by additional equipment (i.e. tension and compression forces, extension, torque, vibration). The sensor body equipped with a connector has an outer diameter of only 8 mm and therefore is especially well suitable for the integration in dimensionally restricted structures. Typical application fields are displacement and extension measurements on: —Machines —Servo systems —Motor vehicles —Test benches —Production plants The cylindrical case made of stainless steel, houses a differential transformer (LVDT). It consists of a primary and two secondary coils with axially moveable core. A displacement of this core changes the magnetic induction of the coils. The INLINE carrier frequency amplifier converts the displacement into a direct proportional electrical DC voltage.

High-precision pressure sensors from the 8201 series provide exact measurements while exhibiting very little sensitivity to mechanical stresses. Their application therefore goes well beyond research and development laboratories. They are also outstandingly suited to industrial use in quality assurance or for measurement and control tasks in production. Their robust mechanical and electrical construction guarantees good long-term stability and high reliability, while being resistant to aggressive media – which can be measured in liquid or gaseous states. The structure of the sensors includes no mechanical moving parts, which is why they show so little sensitivity to impact and vibration. The pressure sensors can be configured with options to suit the user. Standard types are available ex-stock, and customized customer versions can also be provided. Aeras of application are: —Research and developmemt —Test rigs —Mechanical engineering —Plant control and monitoring

The ideal introduction to the world of vibration measurement. With four analog input channels, the Mosquito offers the ability to detect a triaxial vibration sensor and a speed signal. Alternatively, a modal hammer could also be operated for a measurement with subsequent modal analysis. •,4 analog input channels (from +/-10uV to +/- 100V) •,1 digital input channel (0-5V CMOS) •,1 analog output with signal generator (DC, 0-100kHz sine, sweep) •,Up to 100kHz bandwidth synchronously sampled across all channels •,16/24 bit resolution with 110+dB signal-to-noise ratio •,Compact dimensions (40 x 90 x 170 mm) •,Freely scalable! From one device with 4 analog channels to multiple devices with any number of channels •,1x Ethernet interfaces, connection for external 12V power supply, LVDS port for synchronization of multiple devices, USB port, IRIG input

The ultra-compact solution for mobile data collection. Five analog input channels with up to 80kHz bandwidth. Up to 12 hours of runtime on a single charge. •,2 to 5 analog input channels •,Up to 80kHz bandwidth synchronously sampled across all channels •,16bit resolution with 90+dB signal-to-noise ratio •,12h battery life (AA batteries can be charged via USB or easily replaced) •,Slot for SD cards with up to 128GB storage capacity (over 19h data recording) •,Compact dimensions (130x75x30mm) and light weight (300g) •,Integrated 4.3" touchscreen for easy configuration and display of measurement results •,USB port •,Integrated sensors (3-axis vibration transducer, 3-axis gyroscope, temperature sensor) •,Integrated Conditioning for IEPE Sensors (available from 2024)

Sensors of the family IGEX22 for use in zone 22 with integrated electronics and direct switching output to the non-explosive area do not need a separate analysis device. This saves space and costs. The EGE IGEX20 proximity switches are based on the conventional inductive principle and switch when a metallic object moves close. This family includes shock and vibration resistant solid stainless steel sensors. The sensors are certified according to ATEX and IECEx. The sensors of this family are suited in the area of explosive dust atmospheres (zone 22) for presence verification, position and movement monitoring and the counting of metallic objects and the speed control on conveyor belts.

Sensors and accessories for vibration measurement and Condition Monitoring Large selection of vibration sensors accelerometers, displacement sensors, VIBCODE transducer and triaxial sensors Accelerometers measure vibration acceleration, shock pulse (roller bearing condition) and pump cavitation Also available in compact size, for lowspeed machines and as combi sensors for vibration and temperature Patented tandempiezo technology eliminates the disadvantages of conventional sensors Highquality signal transmission over long distances up to 1,000 meters (3,200 feet) with current line drive (CLD) signal amplification Various mounting types EX / ATEX versions available Temperature probes, keyphasers, cables, adaptors and tools available

Current loop powered vibration transmitters enable cost-effective and permanent monitoring of machine vibrations. They provide a standardised 4 ... 20 mA output signal, which is proportional to the RMS or peak value of the measured vibration amplitude. The transmitters are connected to existing, free inputs of a PLC or a process control system. These then issue a warning message when a preset vibration level is exceeded or switch off the machine in an emergency. — Measuring range 0 ... 25.4 mm/s — Output range 4 ... 20 mA — Frequency range 3 ... 1,000 Hz — 2-pin connection socket on top. For an individual offer, please contact us directly.

The Model 682C05 signal transmitter is used on the one hand to supply ICP(R)/IEPE vibration sensors and essentially to provide early warning of developing faults in rolling bearings, such as damage to the inner or outer ring, play and lack of lubrication. The unit provides two output signals, the vibration level and information about high-frequency peaks or shocks. The module also has a raw signal output for connecting machine condition analysers. For an individual offer, please contact us directly.

The Model 682C03 signal converter can be used to supply constant current-fed ICP®/IEPE accelerometers and connect them to 4 ... 20 mA signal circuits. The signal converter supplies an output current proportional to the RMS or peak value of the vibration acceleration, the vibration velocity or the vibration displacement (adjustable). For an individual offer, please contact us directly.

Acceleration sensors with ICP®/IEPE technology are usually used for vibration monitoring. Sensors for series use are particularly suitable if a large number of measuring points are to be monitored. The low-cost sensor models, where the sensor model 627A01 belongs, can be integrated permanently into monitoring systems or used in conjunction with a portable data collector/analyzer for route-based monitoring. The accelerometer presented here, model 602D01, can be used in ambient temperatures up to 121 °C. If the operating conditions require it, this model is also available with EX approval or with SIL-2 declaration. All sensors are supplied with a 1-point calibration according to ISO 17025. — With through hole — Measuring range 50 g — Sensitivity 100 mV/g — Frequency range 0.5 ... 8,000 Hz — Single-point calibration at 100 Hz — 2-pin connection socket on the side Please contact us directly for an individual offer.

The low-cost High Temperature ICP®/ IEPE accelerometer, model HT602D01, is ideal for vibration measurements in higher temperature applications, including the paper, plastics and steel industries. These high temperature ceramic shear ICP® accelerometers feature a 2-pin MIL-C-5015 side-exit connector in a low-profile package. They can be used in environments with temperatures up to +325°F/+163°C. The sensing element of these accelerometers provides a sensitivity of (±10%) 100 mV/g (10.2 mV/(m/s²)) with a frequency range of (±3dB) 30 to 480000 cpm (0.5 to 8000 Hz). — Industrial ICP® vibration sensor — Continuous operating temperature up to 163 °C — With through hole — Measuring range 50 g — Sensitivity 100 mV/g — Frequency range 0.8 ... 8,000 Hz — Single-point calibration at 100 Hz — 2-pin connection socket on the side Please contact us directly for an individual offer.

Usually, acceleration sensors with ICP®/IEPE technology are used for vibration monitoring. Sensors for series use are particularly suitable if a large number of measuring points are to be monitored. The low-cost sensor models, where the sensor model 627A01 belongs, can be integrated permanently into monitoring systems or used in conjunction with a portable data collector/analyzer for route-based monitoring. The accelerometer presented here, model 627A01, can be used in ambient temperatures up to 121 °C. If the operating conditions require it, this model is also available with EX approval or with SIL-2 declaration. All sensors are supplied with 1-point calibration according to ISO 17025. The industrial accelerometer, model 627A01, is equipped with a quartz sensing element. — Measuring range 50 g — Sensitivity 100 mV/g — Frequency range 0.33 ... 10,000 Hz — Single-point calibration at 100 Hz — 2-pin connection socket on top For an individual offer, please contact us directly

Cost-effective industrial ICP®/ IEPE accelerometers are ideal for fixed installations and use in continuous on-line monitoring systems. This improves safety when installed in hazardous or inaccessible locations. Connection can be made via switches or junction boxes for route-based data acquisition systems. The Model 601A01 is suitable as a low-cost industrial ICP®/ IEPE accelerometer for a general purpose. It has a very good signal-to-noise ratio and a ceramic sensing element. The low-cost ICP®/ IEPE accelerometers have an economical design and are ideal for fixed mounting. Their rugged stainless steel housing with hermetic sealing and housing-isolated electronics, eliminate noise problems. — Industrial ICP® vibration sensor — Measuring range 50 g — Sensitivity 100 mV/g — Frequency range 0.27 ... 10,000 Hz — Single-point calibration at 100 Hz — 2-pin connection socket on top For an individual offer, please contact us directly.

The low cost industrial ICP® / IEPE vibration sensor, model 601A02, is suitable for slow speed applications such as slow moving roller element bearings in a paper mill. Increasing the sensitivity of the sensor to 500 mV/g can improve the signal resolution in these applications. Despite their economical name, low-cost accelerometers are ideal for applications where the sensors are permanently mounted to collect vibration data 24/7, monthly or even quarterly. Low-cost accelerometers are all hermetically sealed in stainless steel housings and most are covered by IMI Sensors' Lifetime Warranty Plus programme. — Industrial ICP® vibration sensor — Measuring range 10 g — Sensitivity 500 mV/g — Frequency range 0.17 ... 10,000 Hz — Single point calibration at 100 Hz — 2-pin connection socket on top For an individual offer, please contact us directly.

The 603C01 ICP® is one model in a very diverse line of 603-Series accelerometers. The 603-Series includes alternative sensitivity models, hazardous area approved models, dual output models and models with an integral cable. For monitoring systems with many input channels, robustness, reliability and a favourable sensor price are of great importance. Low-cost sensors with ICP®/IEPE technology are used when a large number of measuring points are to be continuously monitored and an evaluation of the vibration spectrum is required. is required. — Industrial ICP®/IEPE vibration sensor — Measuring range 50 g — Sensitivity 100 mV/g — Frequency range 0.5 ... 10,000 Hz — Single-point calibration at 100 Hz — 2-pin connection socket on top — With metric (M) or inch mounting bolt If you have any further questions about this sensor model, please do not hesitate to contact us. We will be pleased to help you.

VIBGUARD compact for individual assets VIBGUARD compact offers six measuring channels for continuous monitoring. It is perfectly suited for fast and highly dynamic equipment. In particular, the VIBGUARD compact meets the requirements of critical assets that are characterized by high availability, high aggregate values, complex drives and changing operating conditions. Whether preinstalled in an IP65 compact housing or as a switch cabinet system module, the VIBGUARD compact is perfect for diagnostic condition monitoring of individual extruders, large fans, multiphase or vacuum pumps, turbocompressors, mill stands, or centrifuges. All six measuring channels are designed as highly dynamic analog input channels and can be equipped with either standard ICP vibration sensors or with voltage input signals for process variables.

Pulsarlube Mi automatic grease lubricator is innovatively designed to detect the operation of industrial rotational machinery by using a piezoelectric vibration sensor. This piezoelectric sensor is composed of a ceramic strain transducer attached to a metallic proof mass in order to respond to an externally imposed acceleration. Fully automated lube system Clear reservoir that is easy to see the remaining grease inside No need for external electric wiring to a motor or other power supplies Possible to choose proper high performance lubricants according to specific environments Reliable constant, precise & predictable lubricant supply Low maintenance cost, competitive with manual lubrication

Inductive proximity switches are contact-free sensors. They detect all conductive metals, regardless of whether they move or not. The achievable sensing range of the devices depends on the object material and its dimensions. The vibration-resistant sensors can be approached laterally or frontally. Inductive proximity switches are used for presence detection (e.g. goods carriers), positioning (e.g. dampers), counting (e.g. nuts /bolts), speed detection (e.g. for cog wheels), on conveyor systems (e.g. hose feedings) or distance measurements (e.g. press-in checking) of metallic objects.

Capacitive proximity switches are contact-free sensors. They detect metallic and non-metallic objects, regardless of whether they move or not. The achievable sensing range of the devices depends on the object material, its dimensions and the response sensitivity, which is set via a potentiometer. The vibration-resistant sensors can be approached laterally or frontally. Capacitive proximity switches are used for presence detection (e.g. sealing detection), positioning (e.g. PET bottles), counting (e.g. plastic caps), level detection (e.g. lubricant) or distance measurements (e.g. thickness measurement) of solid and liquid materials.

Inductive proximity switches are contact-free sensors. They detect all conductive metals, regardless of whether they move or not. The achievable sensing range of the devices depends on the object material and its dimensions. The vibration-resistant sensors can be approached laterally or frontally. Inductive proximity switches are used for presence detection (e.g. goods carriers), positioning (e.g. dampers), counting (e.g. nuts /bolts), speed detection (e.g. for cog wheels), on conveyor systems (e.g. hose feedings) or distance measurements (e.g. press-in checking) of metallic objects.

Inductive proximity switches are contact-free sensors. They detect all conductive metals, regardless of whether they move or not. The achievable sensing range of the devices depends on the object material and its dimensions. The vibration-resistant sensors can be approached laterally or frontally. Inductive proximity switches are used for presence detection (e.g. goods carriers), positioning (e.g. dampers), counting (e.g. nuts /bolts), speed detection (e.g. for cog wheels), on conveyor systems (e.g. hose feedings) or distance measurements (e.g. press-in checking) of metallic objects.