Probes - Import export

Robust and highly accurate incremental probes with magnetic operating principle and USB interface for easy evaluation. The gauges are available with the following measuring ranges: 10mm / 25mm / 50mm / 100mm. Extremely insensitive to contamination such as oil mist, moisture and dust. Due to the Ø 20mm clamping shaft extremely robust against oscillations and vibrations Perfectly suited for automated data acquisition in measuring fixtures, assembly and manufacturing plants. A simple evaluation software for the USB interface is included.

Incremental length probe with magnetic detection principle for high reliability. Very high accuracy and repeatability Extremely insensitive to contamination such as oil mist, moisture and dust Ball spline bearing of the spindle for long life time Perfectly suited for automated measured value acquisition in measuring devices, assembly and manufacturing lines

High accuarcy incremental length probe with magnetic operating principle. Extremely insensitive to contamination such as oil mist, moisture and dust Due to the Ø 20mm clamping shaft extremely robust against oscillations and vibrations Perfectly suited for automated data acquisition in measuring devices, assembly and production lines

For measuring gas concentration in shafts or just below the ceiling.

■ Measuring on turbo vanes and shafts ■ TTL output for speed measurement ■ Analogue monitor output for gap control ■ High resolution ■ High dynamics ■ Low current consumption ■ High noise immunity

The new Scout VGS 4500 measuring station consists of measuring probes mounted on the front of the vehicle and a measuring cell installed within the vehicle. These two parts are connected via a suction hose. The system can be mounted on different type of vehicles such as a pickup truck, quad or car. To adapt to nature of the surface to be measured, the probe distance can be adjusted quickly and it is just as easy to store the entire front probe. With the Scout VGS 4500 measuring station from Schütz, very large sections of network can be inspected and the results can be recorded in a short time. With the vehicle-based measuring system, measurements are accurately taken at speeds up to 50 km/h. Even under the most difficult conditions, Scout VGS 4500 has proven its reliability. The system was successfully subjected to a resistance test in the desert at an outside temperature of over 36 degrees Celsius.

Incremental lengths probe with magnetic operating principle. Extremely insensitive to contamination such as oil mist, moisture and dust. Perfectly suited for automated measured value acquisition in measuring devices, assembly and manufacturing plants.

United Process Controls' probe certification program is designed to maximize the life of a probe and ensure the most accurate readings possible. All probes are tested in a certified atmosphere against a probe standard and must meet deviation criteria.

Weight-optimized borehole probe with demountable carbon fiber rod and integrated filter technology. (Dust and water filter) Extremely light, yet very rugged construction for fatigue-free work. The borehole probe has a sight glass, dust filter and water filter integrated in the lower part. The dmountable borehole probe CFRP is available in a carrying case complete set with borehole probe CFRP, bell probe CFRP and weight-optimized foldable carpet probe CFRP made of carbon fiber.

The accessibility of the lines for pressure tests in industrial companies is often a major problem, but no longer with this probe!

The accessibility of the lines for pressure tests in industrial companies is often a major problem, but no longer with this probe!

Weight-optimized bell probe with carbon fiber rod and integrated filter technology. Extremely light, yet very robust construction for fatigue-free work. The bell probe has a dust and a water filter integrated in the lower section and is used for unpaved surfaces. When the carpet probe can no longer be used, the bell probe is used for above-ground control or for concentration measurement in the ppm range. Both probes are often carried along; the CFRP mini bell probe is ideal for this. The Bell Probe CFRP Mini is particularly suitable for carrying along with the carpet probe during pipeline network inspections. The Bell Probe Mini is clicked into the rod of the carpet probe. Together with the Carpet Probe CFRP, the combination of both probes weighs less than a metal constructed probe, with the same or higher strength.

Weight-optimized bell probe with steel rod and integrated filter technology. This probe is included in the complete set. Extremely light, yet very robust construction for fatigue-free work. The bell probe has a dust and a water filter integrated in the lower section and is used for unpaved surfaces. When the carpet probe can no longer be used, the bell probe is used for above-ground control or for concentration measurement in the ppm range. Both probes are often carried along; the CFRP mini bell probe is ideal for this. All bell and borehole probes are available with a demountable rod to fit in the carrying case - complete set with borehole probe CFRP, bell probe CFRP and foldable carpet probe CFRP weight-optimized.

Weight-optimized bell probe with steel rod and integrated filter technology. Extremely light, yet very robust construction for fatigue-free work. The bell probe has a dust and a water filter integrated in the lower section and is used for unpaved surfaces. When the carpet probe can no longer be used, the bell probe is used for above-ground control or for concentration measurement in the ppm range. Both probes are often carried along; the CFRP mini bell probe is ideal for this. All bell and borehole probes are available with a demountable rod to fit in the carrying case - complete set with borehole probe CFRP, bell probe CFRP and foldable carpet probe CFRP weight-optimized.

Weight-optimized bell probe with carbon fiber rod and integrated filter technology. Extremely light, yet very robust construction for fatigue-free work. The bell probe has a dust and a water filter integrated in the lower section and is used for unpaved surfaces. When the carpet probe can no longer be used, the bell probe is used for above-ground control or for concentration measurement in the ppm range. Both probes are often carried along; the CFRP mini bell probe is ideal for this. All bell and borehole probes are available with a demountable rod to fit in the carrying case - complete set with borehole probe CFRP, bell probe CFRP and foldable carpet probe CFRP weight-optimized.

For in-depth measurements in boreholes. Complete with water separator, suction hose, sintered filter and coupling. The measuring tip comes closer to the leak point or the gas mains and kann thus deliver better results.

Borehole probe with sight glass, dust filter and water filter for concentration measurement in boreholes. The bore hole is sealed by the flexible cone and no external air is sucked in. With a max. depth of 30 cm the borehole can be used without any problems.

Easy to guide push along carpet probe with surface filter, hose filter, hose and plug-in coupling for the inspection of pipe runs, to absorb gas traces during the mains survey with the aspiration method. Very lightweight - for daily use without fatigue. The wide border of the flexible carpet probe clings to surface unevenness of the street, largely preventing the entrance of interfering gases (exhaust fumes, ?) during the survey work.

Easy-to-use, mobile carpet probe with surface grille, bag filter, hose and plug-in coupling for surveying pipelines, and for recording gas traces after checking the gas pipeline network with the suction process. Very light, therefore fatigue-free and easy to use in daily tasks. The wide edge of the flexible carpet probe conforms well to unevenness on the pavement surface and largely prevents the ingress of interfering gases (exhaust gases) during the inspection process.

Easy-to-use, mobile carpet probe with surface grille, bag filter, hose and plug-in coupling for surveying pipelines, and for recording gas traces after checking the gas pipeline network with the suction process. Very light, therefore fatigue-free and easy to use in daily tasks. The wide edge of the flexible carpet probe conforms well to unevenness on the pavement surface and largely prevents the ingress of interfering gases (exhaust gases) during the inspection process.

Easy-to-use, mobile carpet probe with surface plate, bag filter, hose and plug-in coupling for surveying pipelines, and for recording gas traces after checking the gas pipeline network with the suction process. Very light, therefore fatigue-free and easy to use in daily tasks. The wide edge of the flexible carpet probe conforms well to unevenness on the pavement surface and largely prevents the ingress of interfering gases (exhaust gases) during the inspection process.

Easy-to-use, mobile carpet probe with surface grille, bag filter, hose and plug-in coupling for surveying pipelines, and for recording gas traces after checking the gas pipeline network with the suction process. Very light, therefore fatigue-free and easy to use in daily tasks. The wide edge of the flexible carpet probe conforms well to unevenness on the pavement surface and largely prevents the ingress of interfering gases (exhaust gases) during the inspection process.

foldable carpet probe (carbon-fibre) 180mm diameter wheel. Bore-hole probe (carbon fibre). Bell-probe funnel for attachment. Telescopic aeriel probe. Instrument filter. Carry-strap. Carry-case. Charger not included. Gas detector not included

With the telescopic aerial probe, any gas traces that may be present can be better detected. This is particularly recommended in pedestrian zones. Due to the high suction power of the extraction system, the gas concentration in the ground is already very diluted. However gas may still be later detected - but not with the telecopic aerial probe. Depending on the requirements, the telescopic aerial probe can be clicked into place quickly.

Four-pole measurement at minimum space: coaxial contact probes with inner conductor as sense pin, from smallest pitches up to highest currents.

At the limit of what is possible: Reliable contact probes for finest structures and semiconductor contacts down to 40μm pitch.

Incremental length probe with magnetic detection principle for high reliability. with USB interface. Very high accuracy and repeatability. Resolution 0,1µm or 0,5µm Extremely insensitive to contamination such as oil mist, moisture and dust Ball spline bearing of the spindle for long life time Perfectly suited for automated measured value acquisition in measuring devices, assembly and manufacturing lines. Basic measuring software included

High-quality and precise humidity / temperature sensor with integrated measuring transducer (output 0-10V) suitable for building automation, drying and air-conditioning technology (HVAC), outdoor or industrial applications.

High-quality and precise humidity / temperature sensor (passive, Pt1000) with integrated measuring transducer (output humidity 0-10V) suitable for building automation, drying and air-conditioning technology (HVAC), outdoor or industrial applications.