High-temperature application - Import export

iglidur® H2: Cost-effective high-temperature bearing up to 200°C Media resistant Low-Cost material. For application with high temperature requirements. Can be conditionally used in dry operation; excellent properties with additional lubrication. iglidur® H2 is available as cylindrical bearings and plain bearings with flange. Usable underwater Low-priced Chemical resistant For high temperatures

iglidur® UW500: For Underwater-Applications For use in hot liquids. iglidur® UW500 was developed for underwater applications in which high temperatures (up to 200°C) occur. With additional lubrication, the bearings can operate in chemicals. iglidur® UW500 is available as cylindrical bearings and plain bearings with flange. For underwater application at high temperatures For fast and continuous movements

Ceramic Insulated (Band) Heaters are predestined for high-temperature applications beyond 450 °C, for example for pipe heating in process heat technology, especially when gases are involved. Ceramic insulated sectional surface heating elements are also brought into action where a heat storage capacity is needed, as in hot plates the case. With the heating surface of ceramic flat heaters being composed by small-limbed ceramic elements with aligned holes in the centre for the resistance coils to be fed through, ceramic sectional heating mats are also applicable for bent or cylindric surfaces. Like Micanite insulated flat heating elements also Ceramic insulated elements can receive a metal sheath. The latter provides additional protection against mechanical load and allows for attaching connection boxes. Another advantage is the easy installation by means of mounting holes in the metal cladding.

Soft-Sealing Cutting Rings provide an additional safety and protection against potential leakage risks, e.g. caused by the settling of purely metallic sealed connections, temperature fluctuations or considerable pressure and vibration loads in the system. "Sweating effects" on the connection points can be permanently avoided. The type FI-WDDS Soft-Sealing Cutting Ring of the STAUFF Connect range is characterised by the elastomer sealing, which is located in a specially designed groove close to the rear end of the 24° taper and protected to prevent loss. An additional o-ring is used to secure the secure the second potential leakage path between the cutting ring and the tube – even in the event of unfavourable tolerances FKM/FPM (Viton®) is used as the standard sealing material and enables problem-free use of the system for challenging applications involving high temperatures or aggressive media. Like all other components in the STAUFF Connect product range, the cutting ring...

Partial Rotation Angle Damping torque 1.96 to 3.43 N ･ m TD69 damper can be used in up to 80°C temperature ambient thanks to the robust ULTEM™ material.

The angle transducers have a magnetic scanning according to the HALL principle. Due to the robust design, critical and interference-free applications in harsh environments can be realized. They have a robust housing (wall thickness > 5 mm) made of aluminium or stainless steel, shaft and ball bearing made of stainless steel, shaft with flattening, rotor with shaft and permanent magnet mounted in prechamber, sensor circuit consisting of ASIC with Hall elements and interface electronics housed in closed main chamber. Two models are available: For low and high temperature applications. The model for low-temperature use is equipped with a special grease for bearings and shaft seal. Seals and shaft seal are made of PTFE. Cable gland with clamping jaw pressure screw and silicone seal. The high temperature model is without shaft seal. Under the rear cover, there is a signal path switch (CW/CCW). On the side there is a preset button (4 mA) placed under a screw plug.

The angle transducers have a magnetic scanning according to the HALL principle. Due to the robust design, critical and interference-free applications in harsh environments can be realized. They have a robust housing (wall thickness > 5 mm) made of aluminium or stainless steel, shaft and ball bearing made of stainless steel, shaft with flattening, rotor with shaft and permanent magnet mounted in prechamber, sensor circuit consisting of ASIC with Hall elements and interface electronics housed in closed main chamber. Two models are available: For low and high temperature applications. The model for low-temperature use is equipped with a special grease for bearings and shaft seal. Seals and shaft seal are made of PTFE. Cable gland with clamping jaw pressure screw and silicone seal. The model for high temperature use is without shaft seal. Under the rear cover there is a signal changeover switch (CW/CCW). On the side there is a preset button (4 mA) placed under a screw plug.

System press fittings from copper and copper alloys for copper pipes according to EN 1057 for solar and high-temperature applications for compressed air. SANHA®-Press Solar system fittings  have red moulded sealing rings made from FKM.

The SANHA®-Therm Industry installation system consists of tried and trusted SANHA®-Therm Industry system press fittings with a red moulded FKM (fluoro and perfluoro elastomer) sealing ring for high temperature applications and SANHA®-Therm carbon steel system pipes.

High-temperature vacuum-formed products made from biosoluble ceramic fibres are lightweight and solid parts or structural elements that can be used at temperatures up to 1.400 °C in air and in aggressive environments, including direct contact with liquid metals. — 100% biosoluble — high temperature resistance — low thermal conductivity — high chemical resistance * — low weight — good tear resistance — high flexibility — easy processing — complicated geometries can be produced — recyclable * to achieve higher acid resistance, a special coating is required. Available from manufacturer. Application: Burner plant components, crucibles, thermocouple housings, coupling devices in continuous casting plants, channel elements of metal troughs, inlet device in the melting of non-ferrous and ferrous metals, gasket in aluminium foundries, gaskets in blast furnaces, expansion joints, pipe insulation, catalyst insulation, repair work in the high temperature range.

High-temperature vacuum-formed products made from biosoluble ceramic fibres are lightweight and strong parts or structural elements that can be used at temperatures up to 1 .600 °C in air and in aggressive environments, including direct contact with liquid metals. — 100% natural — biosoluble — high thermal shock resistance — low thermal conductivity — high chemical resistance * — recyclable — low weight — good tear resistance — high flexibility — easy processing — harmless to health — complicated geometries can be produced * A special coating is required to achieve high acid resistance. Available from manufacturer. Fields of application: gaskets, crucibles, thermocouple housings, coupling devices in continuous casting plants, expansion joints, convex and flat gaskets in blast furnaces, channel elements of metal troughs, inlet device in the melting of non-ferrous and ferrous metals.