Forcing - Import export

AVAILABLE KÉRASTASE HAIR CARE AND SHAMPOO EU CLEAN AND QUALITY CERTIFIED FOR MORE INFORMATION PLEASE DO NOT HESITATE TO CONTACT US.

Its Virtues To restore hair worthy of a goddess, this hair serum combines CBD with castor oils, jojoba, sweet almond, avocado & an oily macerate of garlic to nourish, revive and repair the fiber.

Steel. Version: Ball thrust pins trivalent passivated. Ball seat and nuts electro zinc-plated. Note: Axial joint suitable for taking up tractive forces. The ball's movement can be controlled or fully locked in position using the clamping nut.

By using clamping levers with integrated clamping force intensifier, the clamping force can be increased by up to 75% compared to standard clamping levers. Furthermore, this product can also be used by persons with limited hand strength (e.g. in rehabilitation) to achieve comparable clamping forces with less effort. Less effort is also needed to loosen the clamping lever. The increase in clamping force is achieved by the integral needle roller thrust bearing, which generates very low surface friction on a rigid contact surface during clamping. The hardened thrust washers are designed for high clamping forces and the bearing with its high load rating guarantees a long service life. The clamped component is permanently protected by the large, stationary contact surface. A washer is no longer required. Due to the modular construction many special designs are available.

Application: Assays Product group: Albumins : Proteins CAS-Nr.: [9048-46-8] Storing temperature: 2-8°C GHS pictogram: GHS07 EINECS: 232-936-2 Purity: >98.0% Shipping condition: ambient Synonym: Fraction V Appearance: white to yellowish flakes MW: 66.5 kDa UNSPSC-No: 41116134 Formula: 583 amino acids

Product group: Reagents Storing temperature: -20°C Shipping condition: ambient MW: 199.25g/mol Formula: C10H17NO3

Application: Staining and Labelling CAS-Nr.: [23491-52-3] Storing temperature: -20°C GHS signal word: Danger GHS pictogram: GHS05 EINECS: 245-691-1 Purity: >98.0% Appearance: yellow to dark yellow powder MW: 615.98g/mol Formula: C27H28N6O3HCl3H2O

Product group: ReagentsCellular Assays/ Detection-Labeling- kits CAS-Nr.: [194041-65-1] Storing temperature: -20°C MW: 443.43g/mol Formula: C14H18N3NaO8S2

Pressing force: 10000kN > 1000 Ton Bending lengths: 6000mm long X 32mm thick. 5000mm long X 40mm thick. 3700mm long X 50mm thick. 3000mm long X 65mm thick. 2500mm long X 75mm thick. Machine is in good condition and immediately available. More info on request.

The peel force is a critical parameter for every user of Tape & Reel. If the peel force is too low, the cover tape will not stick on the carrier tape properly and the components may fall out of the pockets. A too high peel force will cause costly down times at the pick & place machines. The KT 5000 peel force tester from KTECH is the ideal tool to measure the peel force on your production floor. For measuring, a strip of the carrier tape is loaded into the KT 5000 and the cover tape is attached to the sensor. The constant movement of the carrier tape is done with a sprocket wheel. The movement speed is controlled with an encoder. The design of the KT 5000 guarantees the same peel angle and the same peel point during the whole measurement. Before each run, the KT 5000 is doing a selfcalibration of the sensor. The measured values are transferred to a PC via a serial RS232 interface. A green bar on the screen shows a good result, if the measurement is out of limit, the bar is red.

The main characteristics of the forced ventilation unit are short assembling measures. The ventilations are static and dynamically balanced, thus, of a high balance quality. The diameter, the length as well as the side punchings can be made to customer´s requirements.

Forced Ventilation Units Forced Ventilation Units type MW in IP 66 with axial ventilation fan to ensure a low run at a simultaneously higher output. These units can be operated at a higher ambient temperature of max. 60 °C.

This forced ventilation series offers a wide voltage range of 220 to 275 (+-5%) Volt single-phase respectively 380 to 480 (+-5%)Volt three-phase in protection class IP 66 The very high stiffness and stability in connection with our flexible assembly possibilities for the extensions and the wide electric field of application offers you a cost-effective, technically high-quality solution for your motors .

Two-person kayak with everything you need to have a great day on the water: 2 oars, a pump and a head. Designed for quick and easy setup, this lightweight kayak is easy to inflate with the included Air Hammer hand pump. It has a floor and two inflatable seats with backrests for added support. Dimensions: 3.31 m x 88 cm Maximum weight: 180 kg Two 230cm aluminum paddles Contents: 1 kayak, 2 paddles, 1 hand pump, 2 fins, repair patch.