Calibrating - Import export

Regular and Adhoc Fuel Calibration & Servicing It is recommended to have tanker meters calibrated on a yearly basis to ensure that they continue to give the correct measure. Alpeco is able to offer this service on a ‘when required’ basis, or a tailored yearly service contract is available, which also includes a thorough service to all Alpeco derived equipment on the customer’s installation. Alpeco is then able to seal the equipment for public use. All Alpeco reference meters follow the same stringent guidelines as applied to all Trading Standards instruments to ensure the utmost accuracy.

Models 105 (Class 1) & 106 (Class 2) acoustic calibrators quickly check the accuracy of your sound level meter or personal noise dosemeter making sure that your measurements and valid and comply with international regulations and codes of practice. Description: Acoustic Calibrator Models 105 (Class 1) and Model 106 (Class 2) have been tested and formally EU Pattern Approved under certificate PTB-1.61.4034842, as meeting all of the requirements of the latest International standard, IEC 60942: 2003. This version of the IEC standard is far more stringent than previous versions and so far very few manufacturers have managed to meet it. The two models are intended to calibrate, that is set the sensitivity, of any properly approved sound level meter that uses a standard measurement microphone ... ** Ask for a quote **

Preparation is key when it comes to SF6 gas analysis. Ensuring the analyser is within calibration is fundamental to safe operation, compliant measurement and accurate testing. Our Verify NIST traceable verification gases can prove the instrument is in specification and valid for use in accordance with ISO9001 requirements for controlled measurement equipment. EMT SF6 gas verification products utilised during operation provide continued assurance that the analyser is performing as it should be, that the measurements shown are accurate, and that these are in line with the measurement values and tolerances of the supplied gas.

The BGP base can be used with any BGP series piston, allowing testing from 15 mbar to 120 bar. The base requires a supply of gas slightly above test pressure, and has precision inlet / outlet valves and a screwpress to enable easy regulation and adjustment of pressure. The BGP1 has a 1/2in2 high chrome steel piston/cylinder unit. The design has been proven over many years to provide excellent sensitivity and stability. Low start pressure is achieved through use of a hollow piston and aluminium head. NOTE: Model BGP1 can be used on vacuum with a model 24 adaptor. All certificates issued for Budenberg Dead-weight Testers are fully traceable to national standards via equipment with UKAS calibration certificates.

The BGH series base can be used with any of the BGH series pistons to give ranges 1-120 bar with a BGH120, 2-300 bar with a BGH300, 1-700 bar with a BGH700 and 1-1200 bar with a BGH1200 . All units are top loading for ease of use and weight sets are fully interchangeable. This means that weight sets in alternative pressures are readily available and customers with more than one %*+ series tester can interchange weight sets between testers of the same range. The base features a dual area screwpress which allows low-pressure priming and high-pressure control. The BGH is a robust design, proven over many years usage. The unit has a 1/16in2 fully hardened and stabilised tool steel piston. This unit gives extremely good sensitivity for high accuracy calibration, yet is tough enough for regular use in a workshop environment.

Model 179 Differential Pressure Gauge The gauge is designed to withstand full working pressure, applied separately to either connection or together. The maximum working pressure should not be exceeded even temporarily, so the possibility of surging pressures should be considered when selecting the instrument. Model 180 Microvar Differential Pressure Gauge Melinex is a polyester film (polyethylene terephtalate) that is resistant to all petroleum refining industry fluids. Please consult our technical department to check the suitability for other chemicals. Model M24 Bellows Type Differential Pressure Gauge Designed around a balanced bellows system, which converts the differential pressure into a rotary movement by way of a torsion tube assembly and mechanical linkages. The entire assembly is liquid filled, producing a hydraulic self lubricating measurement system which allows for full line pressure to be applied to either side of the unit without damage to the device.

Bourdon Tube Pressure Gauge - Defence Standard Designed for Naval and Marine applications in accordance with Def Stan 66-2. This gauge has been designed to withstand high level of shock and are all manufactured in accordance with EN837 -1. The 4" and 6" flush mounting versions are available with 3 Hole front fixing flange . Bourdon Tube Oxygen Pressure Gauge The 950GP incorporates a solid baffle wall and blow-out back for operator protection and standard features such as IP67 environmental protection, not normally available on comparative units. The 950GP is specifically manufactured for use on OXYGEN and as such is cleaned for Oxygen service with no oil or grease contamination. A restrictor in the inlet is a standard feature. BFMIRA Vacuum Gauge (Can Piercing Test) The Model 269 is a high specification vacuum gauge specifically designed for the estimation of the intensity of vacuum in a food can. Developed by the British Food Manufacturing Industries Research Association.

Schaffer Diaphragm gauges are designed for use on slurries, viscous or corrosive fluids that would normally attack or block standard bourdon tube gauges. 316 Stainless Steel full safety pattern case. Implementing specialist materials for both the connection and diaphragm enable the Shaffer Diaphragm gauge to be configured for use on any gaseous or liquid media including suspended solids or powders. The direct drive from the diaphragm to the movement ensures a more positive indication of pressure than other models of tube gauges. Offering a full range of screwed connection sizes and materials, Schaffer Diaphragm gauges can operate at pressure ranges as low as 30 mBar with the option to permit units to withstand a maximum pressure of 70 bar.

Model 5214 Standard Test Gauge Our 0.25% accuracy Standard Test Gauge is undoubtedly recognised as a world leader for its accuracy and, of course, Budenberg Quality. This gauge incorporates a base test gauge accuracy with to a maximum of 500 graduations where possible, along with a knife edged pointer and an anti parrallax mirror to help reduce the chance of human error. Model 5314 MasterTest Gauge The 5314 now provides a higher specification and incorporates many additional features as standard. Housed in a new die-cast safety pattern case, the 5314 meets the full requirements of EN837 including a brighter anti-parallax mirror scale & knife-edge pointer for accurate repeatable readings. Model 5414 Super Test Gauge The 5414 now provides a higher specification and incorporates many additional features as standard. Housed in a new die cast safety pattern case, the 5414 meets the full requirements of EN837.

Sizes: 63 mm & 80mm Dial diameter and 100 mm (4”) & 150mm (6") Mounting: Direct, Surface and Flush Case & Bezel: Full Safety Pattern case to S3 standard and Die Cast Scale Ranges: 0 to 600 mbar to 0 to 1400 bar, 0 to 400 mBar up to 0 to 1400 Bar Pressure Element: ≤80 Bar for 316 Stainless Steel Bourdon Tube and ≥81 Bar for 316 Stainless Steel Coil Overload: Up to 130% of FSD Pressure Connection in 316 Stainless Steel: 3/8”, 1/2” BSP and 1/2" NPT Accuracy Class: 1% of FSD (CL1) as defined in EN837-1 (Options available) Operating Temperature: -20 to +90 ºC operating Dial: White Anodised Aluminium marked in black finish Pointer: Stainless steel coloured black Movement: Stainless Steel Construction Window: 3mm Laminated Safety Glass (Standard) Environmental Rating: IP67 as defined in EN 60 529 Traceability: Calibrated with unique Serial Number printed on the dial Certification: BS EN 10204 3.

The Classic range of Pressure Gauges has been designed to meet the high demands of the process industry. From harsh corrosive chemical applications to general engineering uses, the Classic combines a high specification with a very cost-effective price. The standard unit incorporates 316 stainless steel wetted parts that are housed within a liquid fillable 316 stainless steel case. Standard units are available as dual scale bar and psi but custom scales can be supplied. 316L wetted parts and cases are available as an option. Available with a wide range of accessories including: Syphons, Snubbers, Gauge Savers, Manifolds, Diaphragm Seals etc ensures that Budenberg can provide you with the right product to suit any individual application or requirement. Scale Ranges: 0 to 1 bar to 0 to 1400 bar or equivalent units of pressure / vacuum are available. Size: 100 mm (4”) & 150mm (6") Mounting: Direct, Flush or Surface

Fast response, exceptional repeatability and accuracy are just some of the standard features of our range of Bimetallic or Filled System Temperature Gauges. We have an extensive range of systems, options and configurations and can provide a cost effective solution to all your temperature measurement needs. Budenberg Gauge Co Ltd is a premier manufacturer of instrumentation for Chemical, Food and Beverage, Oil and Gas, Petrochemical, Pharmaceutical, Power Generation and Transmission, Refrigeration, Water and Waste Water markets. Quality and reliability have become the trademark of all Budenberg products and all our instruments are supplied with a minimum 1-year guarantee and carry a unique serial number for traceability purposes. Budenberg provides highly specialised machined - to complete products for niche industries globally. Our resources allow for bespoke solutions from finished product to machined components.

Over time, various factors such as exposure to contaminants, age, incorrect operation, sensor deterioration, a drift in electronics or exposure to corrosive gases, can contribute to dewpoint instruments losing accuracy and reliability. To maintain accuracy and reliability, we advise an annual service and calibration. For instruments used in critical applications or aggressive environments, more frequent service and calibration intervals are recommended. Our Calibration Laboratory Engineers perform routine servicing, commissioning, fault finding, repairs and installation services in accordance with our accredited quality system. Our calibration range of -90 °C to +20 °C dewpoint is traceable to National and International Humidity Standards at the National Physical Laborarory (NPL). SHAW products are developed to be reliable, easy to install and simple to operate, We are committed to providing the highest quality products and services for accurate and reliable moisture measurement.

This is a calibrated pair of a SingleTact sensor and I²C electronics board. It comes with 4 jumper wires and Calibration sheet. We have various combinations of sizes and pressure ranges, please select a sensor that meets your criteria. A handy Help Me Choose page can assist you with the selection. The sensor and electronics are a matched pair, the calibration is stored on the electronics. You can use a tail extender with calibrated systems, but not interchange with other sensors.

This is a calibrated pair of a SingleTact sensor and USB electronics board. It comes with 50 cm USB cable and a Calibration sheet. We have various combinations of sizes and pressure ranges, please select a sensor that meets your criteria. A handy Help Me Choose page can assist you with the selection. The sensor and electronics are a matched pair, the calibration is stored on the electronics. You can use a tail extender with calibrated systems, but not interchange with other sensors.

Our non-refillable calibration gas canisters are designed specifically for the calibration and bump testing of single and multigas analysers. We offer a wide range of gas mixtures, with the option of multigas mixtures too. Our 34L, 58L, and 110L gas canisters provide the ideal solution for functional testing of gas detection and analytical equipment and being lightweight and compact means they can be easily carried in the workshop or on site. All of the canisters in our range are disposable and can be recycled when empty by using our handy recycling tool.