Cement and additives - Import export

USES AND APPLICATIONS Small cementations, underground rafts and filling. General rehabilitations. COMPOSITION Crushed limestone aggregates of adjusted/correct granulometry (6/12mm and 0/5 mm) Portland Cement CEM 142.5R Additives APPLICATION METHOD Add 2.5 liters of water for each bag of concrete to obtain a soft consistency that will generate the indicated compressive strength. Knead well by hand or mechanically. Do not use at temperatures above 35° C or below 5° C.

Dry cement mortar made with aggregates and additives that give it optimum workability and adhesion, for the construction of walls, partitions in masonry or stone, the creation of coatings, joints and masonry work in general. For interior and exterior use.

Cement whitewashing, replastering, whitewash/rendering, masonry-brick walls, masonry/rubble walls, walls/ chicane/partition, roofing, vaults. COMPOSITION Conglomerates: Portland cements CEM I 42.5 R or BL-II42.5R Crushed aggregates with maximum dimensions of 2 mm (minerals of calcareous nature). Additives: fluidifier - plasticizer. METHOD OF APPLICATION Add 3.5 liters of water for each bag of porter. Knead well until obtaining a homogeneous paste. Place the mass on a clean support and spread it with force. At high temperatures, insolation or very absorbent supports, moisten beforehand. Do not use at temperatures above 35° C or below 5° C.

It is a conglomerate of marble and cement aggregates, packed dry so that 1 user, by mixing it with the indicated quantity of water, obtains a non-structural concrete of adequate and constant quality to form volumes of materials, such as sidewalk concrete, curb concrete and filling concrete.

Improved single-component adhesive cement, highly deformable, with excellent workability and adherence, without slippage and with a long open time. USES For floor and wall coverings. Laying tiles and floor coverings of all types of ceramic or natural stone rooms. Suitable for all types of surfaces. Particularly suitable for laying large format ceramic tiles, facade coverings, tile overlaps, heated floors, cold rooms, high traffic floors, swimming pools, waterproofed substrates, suitable for plaster or anhydrite substrates.

Cement-based self-levelling mortar for low thicknesses 5-20 mm, type CT-C30-F7-A22, made with marble aggregates and special additives that give it optimum fluidity, to be used for the regularisation, repair and levelling of paving slabs. It is a product with high mechanical resistance and a good surface finish, ideal for the creation of continuous screeds. This mortar can be applied on a wide range of supports such as concrete, cement screeds, anhydrite, ceramic or natural stone, both indoors and outdoors.

Improved single-component adhesive cement with excellent workability and adhesion, reduced slip and extended open time. USES For interior and exterior floors, interior coverings. Laying and covering floors of all types of ceramic or natural stone rooms. On traditional mortar plaster supports, concrete, large-format bricks, plaster and plasterboard, anhydrite, waterproofed supports, etc. Particularly suitable for: Floors with heavy traffic, swimming pools, applications with permanent humidity and frost, suitable for plaster or anhydrite supports.

Self-levelling mortar based on cement, reinforced with fibres, modified by additives that give it the ability to be fluid and pumpable, especially intended for screeds and levelling of coverings with a thickness between 5 mm and 50 mm, which, once hardened, must be covered with coverings. USES Applicable on concrete or cement mortar supports. On supports with low porosity, apply a Fixmar Primer GR bonding primer beforehand. Regularisation of continuous screeds. Ideal in situations where a flat surface is required as a support for the subsequent application of another type of covering, such as parquet, carpet, ceramic, linoleum, ceramic materials, marble... Suitable for underfloor heating and as a finishing product for synthetic coverings.

Pre-dose cement-based mortar with corrosion-passivating additives, fast-hardening and reinforced with synthetic polymers.

It is a conglomerate of crushed marble aggregates, lightweight aggregates and cement, bagged in a dry state so that the user, by mixing it with the indicated water, obtains a low density concrete of adequate and constant quality.

It is a conglomerate of marble and cement aggregates, bagged in the dry state so that the user, by mixing it with the indicated water, can obtain a non-structural concrete of adequate and constant quality to form volumes of materials, such as concrete for sidewalks, concrete for curbs and concrete for backfilling.

It is a conglomerate of marble and cement aggregates, bagged in a dry state so that the user, by mixing it with the indicated water, can obtain a mass concrete, reinforced or pre-contracted. Of adequate and constant quality.

Dry cement mortar composed of aggregates, lime and special additives which give it optimum plasticity, workability and adhesion.

Industrial mortar made from marble aggregates and special additives which reduce water absorption and permeability and give it optimum workability, workability and adhesion, for common use in masonry.

Industrial mortar made from marble aggregates and special additives which give it optimum workability, workability and adhesion, for everyday use in masonry.

Single-component powder mortar based on cement, marble and silica aggregates, synthetic resins and special additives that reduce water absorption and permeability and give it optimum workability and docility for its application, as well as being characterized by very high abrasion, high compressive strength, as well as an ideal fineness for a smooth finish.

Primer and adhesion promoter based on acrylic polymers with low emissions of volatile organic substances. Ready to use for interior and exterior use, with inert fillers that give it a textured surface.

Industrial mortar composed of cement, lime, marble aggregates and special additives that give it good impermeability and breathability. It can be applied manually or using a spraying machine

Industrial mortar composed of cement, lime, marble aggregates and special additives that give it good impermeability and breathability. It can be applied manually or using a spraying machine.

Industrial mortar composed of cement, marble aggregates and special additives that reduce water absorption and permeability and give it optimum fluidity for manual and mechanical application, for daily use.

Industrial mortar composed of cement, marble aggregates and special additives which give it optimum fluidity for manual and mechanical application, for daily use.

Latex formulated with polymers in aqueous dispersion which, pure in some cases, serves as an adhesion bridge, and in other cases, mixed with hydraulic mortars, improves their flexibility, their impermeability, their adhesion and their resistance to compression and traction.