Tube plates - Import export

zinc diecasting, nickel plated*for tubes up to 30 mm Ø*with wheel made from*hard metal

Housing aluminium. Precision tube nickel plated steel. Trapezoidal thread spindle steel. Note The doubletube linear actuator can be operated manually or electrically. Due to the short duty cycle, the units can be adjusted several times a day at low speed and with high stability. Width, length and height adjustment possible.

Base plate made of metal, black powder-coated, chrome-plated stand tube - ectendable from 320 - 620 mm - with poster frame and T-piece made of sturdy plastic.

Our pallet stand "UP" is used wherever palletised goods are offered at the POS and a labelling or marking of the products is required. For example, in the DIY or beverage market or wholesale. The powder-coated base plate has a size of 250 x 300 mm. It can easily be slid under the side of the pallet. In this way it has a firm stand. The tube fixed to the plate has a length of 1700 mm. Various accessories such as clamps and frames can be attached to it as required. These can be found under accessories. Clamps and frames are not included in the delivery.

SPIROL offers Spacers specifically designed for use in conveyor systems and garage door hinge assemblies. Both SPIROL's Conveyor Spacers and Garage Door Spacers are manufactured from galvanised steel to provide the necessary strength and corrosion protection at a fraction of the cost of plated cutoff tubing and machined bushings. SPIROL stocks the raw material and tooling required to manufacture the standard sizes of Conveyor Spacers and Garage Door Spacers. Intermediate lengths can be produced without additional tooling.

We have all types of industrial heat exchangers, including: plate and frame shell and plate shell and tube fin/fan They’re refinery-grade, thoroughly cleaned, pressure tested and certified contaminant-free before each use. Capable of handling temperatures from -50ºC to +300ºC, they can also accept volatile gases and liquids, high pressures (up to 40 barg), hydrocarbons, sea water, effluent and brine. With a wide range of supporting ancillaries we can connect our heat exchanger units into any system design with minimum disruption. Heat exchanger hire with expert service support – every time Whether you’re facing emergency bottlenecks, turnarounds or seasonal cooling needs, our process engineers will work closely with you to find the best solution. They’ll visit your site, assess your needs, then design and size your project using their experience, simulation software and stream physical properties. We can also assess the performance of existing heat exchanger

ECU 99,9 % : Electrolytic is used as copper material with a conductivity of 58, electrode in erosion, high-low current panel and busbar in substations. Among our standard products: Rod, Sheet Plate, Straight pipe, Tube Coil, Box profile, Grounding rod - plate, Roofing, Copper fittings and thin wires. Also, sheet plate measurements which do not have a standard are brought to necessary measurement by forging at desired dimensions. Parts that require CU-Cr-Zr (Chromium alloy) High electricity conductivity, hardness and strength at high temperatures: Are used as point welding electrode and seam welding disc at the source of low carbon steels (Panel radiator, Gasoline warehouse, etc.) and Galvanized steel plate (Automotive and white goods), electrode holder at spot welding machines, plunger electrode at erosion machines and contact busbar at substations.

VIN ENGRAVING MACHINE The Vehicle Identification Number (VIN) marking on chassis requires a reliable scribing machine, able to perform deep marking on all materials, from soft, such as aluminum to the hardest steels at a high speed. Our SV530 scribing marking machine has been used for more than 10 years with automotive products, proving fantastic durability and strength. SILENT MARKING SYSTEM Scribing technology performs silent marking on hollow metal parts (tubes and pipes) or formed plates (chassis and body parts) when these objects will naturally resonate during rotary marking. DIRECT PART MARKING Designed to combine depth with high speed and aesthetic results, our scribe marking machine has one of the best-marking speed/depth ratios: mark 17 characters of 7mm high. Powerful and fast, this machine creates deep marking before and after the treatment of parts.

QUIET DPM MACHINE Scribing technology makes sense as a metal marking machine, for metal parts (tubes and pipes) or formed plate (chassis and body parts) which will naturally resonate during dot peen marking. Scribing, by reducing the number of impacts, will allow a smooth and near silent marking with high contrast, making it easier to proofread. Thanks to the Datamatrix kit, we offer you the possibility to switch to a dot peen mode when you need to mark a 2D code. QUALITY SCRIBING MACHINE Designed to combine depth with aesthetic results, speed, strength and position can be configured for perfect direct part marking consistency and legibility meaning a high possibility to survive the painting process. This gives the highest quality characters with the existing fonts. STRONG & DURABLE INDUSTRIAL MARKER Composed of high rigidity guide rails and high-performance styluses. high amplitude, anti-burrs, and a diamond tip.

ECU 99,9 % : Electrolytic is used as copper material with a conductivity of 58, electrode in erosion, high-low current panel and busbar in substations. Among our standard products: Rod, Sheet Plate, Straight pipe, Tube Coil, Box profile, Grounding rod - plate, Roofing, Copper fittings and thin wires. Also, sheet plate measurements which do not have a standard are brought to necessary measurement by forging at desired dimensions.

The Aluminum oxide (Al2o396%) ceramic substrate are widely used in thick-film circuit of electronics industry. Large scale integrated circuit,power hytrid IC,semiconductor package,pieced -film reistor, network,resistor, focusing potentiometer etc.According to the demands of customers,our company can manufacture products of special types and specifications. The Maximum dimension of ceramic plate is 138x138mm and the thickness of ceramic plate ranges from 0.25 to 1.0mm. Features: 1.High reliablility and sfety; 2.High density and mechanical properties 3.High electrical and thermal loading perormances 4.Low dilelectic loss and other characteristics

EDM Electrodes made of the tungsten alloy SPARKAL are available as tubes, rods, square rods and plates in different dimensions in the Plansee Online Shop. Order fast and easily from the producer's online shop: www.plansee.com/shop.

32pin, SMT, tin plating, tube packing

Tower is a group of manufacturing facilities, offering one-stop solution for quality mechanical products with total lower cost in China. We can supply a full-range of metal products, such as sheet metal fabrication, cnc machining parts, casting parts, especially assembly parts. Product market range cover auto industry, medical industry,agricultural machinery, sport industry and so on. Because of our complete equipments, we are very suit for making all kinds of Assembly Parts. All of our products are customized by customer's drawing. Please feel free to send us your drawing or sample to customize!!!

Weight: 19,69 kg; Working/Test pressure: 16 MPa / 20 MPa; Outer diameter of the cylinder: 95 mm; Hydraulic connector: M22*1,5; Required volume of oil: 2 L; Start pressure: 0,5 MPa; Piston extension/retraction speed: 0,5m/s; Permissible ambient temperature: -40 to +60℃; Permissible oil temperature: -15 to +80℃; Type of gland: threaded, screwed into the tube; Piston rod chrome-plated: 20µm; Type of fluid: mineral oil based hydraulic fluid;

Weight: 19,69 kg; Working/Test pressure: 16 MPa / 20 MPa; Outer diameter of the cylinder: 95 mm; Hydraulic connector: M22*1,5; Required volume of oil: 2 L; Start pressure: 0,5 MPa; Piston extension/retraction speed: 0,5m/s; Permissible ambient temperature: -40 to +60℃; Permissible oil temperature: -15 to +80℃; Type of gland: threaded, screwed into the tube; Piston rod chrome-plated: 20µm; Type of fluid: mineral oil based hydraulic fluid;

The OPTIBAR DP 7060 is a differential pressure transmitter with integrated absolute pressure measurement. It offers a high degree of modularity for various flow, hydrostatic level or process pressure applications. For DP flow measurements it can be perfectly combined with the KROHNE primary elements (e.g. orifice plates or pitot tubes). Featuring a quick response time of just 125 ms, the DP transmitter offers high accuracy and measurement stability under all process conditions. KROHNE is the only manufacturer of process instrumentation to carry out a total 3D linearization of its differential pressure transmitter. For a robust and accurate differential pressure measurement, even under changing process conditions, each OPTIBAR DP 7060 differential pressure transmitter is linearized in all three dimensions during calibration: differential pressure, ambient temperature and static pressure are taken into account in combination.

Designed as in-tank suction strainer elements for direct installation into suction lines of pumps; should always be installed below the minimum fluid level of the reservoir Features ▪ Available with female BSP thread (ISO 228) or female NPT thread (ANSI B1.20.1) Materials ▪ Threaded end cap made of glass-fibre reinforced Polyamide (PA) or Aluminium ▪ Lower end cap and support tube made of Steel, zinc-plated ▪ Standard filter material is Stainless Steel Mesh (125 μm); alternative micron ratings of 60 μm and 250 μm on request Consult STAUFF for alternative materials. Media Compatibility ▪ Suitable for use with Mineral and Petroleum based hydraulic fluids (HL and HLP) Technical Data ▪ Operating temperature range: -20 °C ... +100 °C / -4 °F ... +212 °F ▪ Integrated bypass valve with an opening pressure of 0,2 bar (3 PSI) to reduce the risks of high-pressure drops that can be caused by contaminated strainer elements or high-viscosity fluids Special sizes, designs, materials and...

Combination of air breather and water removal filter Features ▪ Available in 4 different sizes ▪ Diameter of Ø100 mm / Ø3.94 in or Ø130 mm / Ø5.12 in ▪ Refillable with drying agent (non-toxic ZR gel grain) or a mix of drying agent and active carbon ▪ Drying agent capable in changing colour from Red to orange with increasing moisture ▪ Without dangerous substances according to EC Council directives 99/45/EC and 2001/60/EC ▪ Replaceable air filter element SGB ▪ Connection: Male BSP thread (ISO 228) on Stainless Steel tube ▪ Available with adaptor plate to simplify installation and to enable the use of a visual contamination indicator ▪ Adaptor plate ▪ Visual contamination indicator ▪ Drying agent refilling material ▪ Active carbon refilling material ▪ Replacement air filter element

Our sophisticated powder metallurgy process allows us to manufacture shaped components including net shapes, bar, plate, rod and tube. These custom-made components are used for critical applications in the mining and drilling, aerospace, electronics and industrial sectors. Pfinodal® (UNS C72900) We offer Pfinodal® (UNS C72900) as a replacement for Toughmet® UNS C72900 material and Beryllium Copper Alloys. AMETEK Specialty Metal Products obtained patents for its powder metallurgically produced product in 1983 and has been serving customers worldwide ever since. Key advantages include: High hardness and strength Non-magnetic properties required in bearing material Low distortion during hardening allows for the complex forming of parts and shapes prior to heat treatment without the need for costly fixtures Non-sparking and non-corrosive Anti-Galling Anti-Seizing Excellent Ductility Excellent Formability Excellent Lubricity Excellent Machinability

This product, featuring purplish red laminated tube and silver plating diamond shape cap, provides an extraordinary temperament and goes very well with luxury brands. Laminate tubes are recommended. Mainly used for top-grade face cream, essene, foundation, primer etc.

This product, featuring a nozzle head with high reflection plating and soft touch finish, will stand out on the shelves to the eyes of customers. Available for extruded tubes (1-layer, 2-layer and 5-layer) and laminate tubes. Mainly used for eye serum, concealor, primer serum etc.

This product, featuring a shiny purple nozzle tube and a high reflection plating cap, communites a premium look and will stand out among its competitors on the shelves. Available for extruded tubes (1-layer, 2-layer and 5-layer) and laminate tubes. Mainly used for eye serum, concealor, primer serum and sample etc.

Particularly robust stainless steel anchorage point with a screw-on supporting tube (Ø 42 mm), base plate (200 x 200 mm) and counter plate (100 x 100 mm). This anchor can be installed in a ceiling, on a facade, on a hollow profile or in lightweight concrete to secure 3 individuals. It can also be implemented as a trouble-free end support in a lifeline system. EN 795:2012, A + CEN/TS 16415:2013 Suitable for installation in a ceiling, on a hollow profile or in lightweight concrete Incl. stainless steel installation set Optional: Installation aid ABS-Lock X-DURCH Sleeve

Bariatric couch Model no. 211.1330.0 800 mm wide, chromium-plated rectangular steel tube frame, collapsible feet, with transverse and longitudinal bracing, 2-section mattress, 70 mm thick foam rubber upholstery, levelling feet, head section adjustable up to +40°. Safe working load: 300 kg. Accessories: Paper roll holder Model no. 200.0940.0 for 800 mm wide couches Paper roll Model no. 200.1030.0 500 mm wide

Wide range capacity liquid cooled condensing units, designed for commercial and industrial applications with the cooling capacity from 10 kW to 40kW. These units work on a principle of the heat rejection loop, where condenser heat is dissipated to the environment via water. Rejected heat can be used for additional needs in the same building, which gives these facilities additional economic benefits. These units provide an economical, compact alternative to traditional air-cooled condensing units. Built on an open welded frame with standard profile, this condensing unit is also available in a double-deck construction for higher capacity. Assembled with shell and tube or plate heat exchanger, 1 to 4 scroll or reciprocating compressors and a liquid receiver as well as refrigerant filters and a sight glass. Safety valve and pressure switches are added to increase the security of the unit.

Wide range capacity liquid cooled condensing units, designed for commercial and industrial applications with the cooling capacity from 10kW to 40kW. These units work on a principle of the heat rejection loop, where condenser heat is dissipated to the environment via water. Rejected heat can be used for additional needs in the same building, which gives these facilities additional economic benefits. These units provide an economical, compact alternative to traditional air-cooled condensing units. Built on an assembled frame with covers, this condensing unit can be designed in a variety of ways, depending on intended use. Collected with shell and tube or plate heat exchanger, 1 to 4 reciprocating or scroll compressors and a liquid receiver as well as refrigerant filters and a sight glass. Safety valve and pressure switches are added to increase the security of the unit. An additional 50 mm rock wool insulation can be supplemented for a super silent unit operation.

ЕСОPAR 10 bar steam boilers are designed for generating saturated steam with a temperature up to 185 °С. Their steamgenerating capacity varies from 0,1 to 10 tons per hour at a steam pressure to 1,0 MPa. The boilers can be used to obtain steam for technological purposes of enterprises, as well as generation of heat energy for the heating systems of residential, public, and manufacturing buildings. The steam boiler with flame inversion consists of a cylindrical furnace with wetted bottom, where flame forms and combustion products are being inverted. Flue gases enter the tube pack of the front tube plate and are sent toward the back tube plate, which they leave through the flue connection. The boiler design ensures low heating and surface loads in the combustion chamber. The boiler body consists of shell, furnace, boiler bottom and flat tube plates made of highquality steel.

ЕСОPAR 10 bar steam boilers are designed for generating saturated steam with a temperature up to 185 °С. Their steamgenerating capacity varies from 0,1 to 10 tons per hour at a steam pressure to 1,0 MPa. The boilers can be used to obtain steam for technological purposes of enterprises, as well as generation of heat energy for the heating systems of residential, public, and manufacturing buildings. The steam boiler with flame inversion consists of a cylindrical furnace with wetted bottom, where flame forms and combustion products are being inverted. Flue gases enter the tube pack of the front tube plate and are sent toward the back tube plate, which they leave through the flue connection. The boiler design ensures low heating and surface loads in the combustion chamber. The boiler body consists of shell, furnace, boiler bottom and flat tube plates made of highquality steel.