Trapezoid screws - Import export

drylin® SLW-1040 linear module, drylin® W aluminium profile, surface: hard-anodised, ball bearing Trapezoidal lead screw TR10x2 made of stainless steel, lead screw end machined 6h9x17mm, guide carriage in 100mm length, shaft end support made of anodised aluminium. Configure drylin SHT linear modules individually here: https://igus.eu/ddx

drylin® SAW-1040 linear module, drylin® W aluminium profile, surface: hard-anodised, Trapezoidal lead screw TR10x2, machined lead screw end 69x15mm, guide carriage, aluminium shaft end support. Stroke length: 500mm, carriage length: 69mm, NEMA23 stepper motor with JST connector. Configure drylin SHT linear modules individually here: https://igus.eu/ddx

drylin® SHT-12 linear module, drylin® R hard-anodised aluminium shafts, Trapezoidal lead screw TR10x2 made of stainless steel with ball bearings, machined lead screw ends 6h9x17mm, quad blocks, aluminium shaft end support, stroke lengths in 250mm or 500mm. Configure drylin SHT linear modules individually here: https://igus.eu/ddx

Lead-free - According to (RoHS) 2002/95/EG Standards and Certificates Leadscrewsstorage Anodized aluminum bearing blocks of iglidur® L250. Design your own linear table. Leadscrewsstorage Single start trapezoidal lead screw Two start trapezoidal lead screw L = Length TR = thread outer diameter m = pitch Leadscrewsstorage Anodized aluminum bearing blocks of iglidur® L250. Design your own linear table. Leadscrewsstorage Single start trapezoidal lead screw Two start trapezoidal lead screw Lead-free - According to (RoHS) 2002/95/EG Standards and Certificates

Lead-free - According to (RoHS) 2002/95/EG Standards and Certificates drylin® trapezoidal lead screw nut - cylindrical nuts with right-hand thread Trapezoidal lead screw nuts made from lubricant-free iglidur® W300, J, J350 and A180. drylin® - trapezoidal leadscrew nuts - WSRM, JSRM, J350SRM and A180SRM drylin® trapezoidal lead screw nut - cylindrical nuts with left-hand thread Trapezoidal leadscrew nuts made from lubrication-free iglidur® W300 and iglidur® J. drylin® - trapezoidal leadscrew nuts - WSLM and JSLM drylin® trapezoidal lead screw nut - flanged nuts with right-hand thread Trapezoidal lead screw nuts made from lubricant-free iglidur® W300, J, J350 and A180. drylin® - trapezoidal leadscrew nuts - WFRM, JFRM, J350FRM and A180FRM drylin® trapezoidal lead screw nut - flanged nuts with left-hand thread Trapezoidal leadscrew nuts made from lubrication-free iglidur® W300 and iglidur® J. drylin® - trapezoidal leadscrew nuts - WFLM and JFLM drylin® Anti-backlash nuts Trapezoidal leadscrew nuts with reduced bearing clearance. Anti-backlash nuts drylin® split lead screw nuts Split lead screw nuts for easy assembly. drylin® split lead screw nut drylin® leadscrew nut - two start two-start lead screws, double stroke in addition to the usual trapezoidal leadscrew nuts. drylin® two-start leadscrew nut drylin® miniature nuts Screw drives ,iniatur lead screw nuts, small sizes. Miniature nuts small sizes drylin® lead screw nuts with spanner flat Ideal transmission of the torque through form fit. drylin® lead screw nuts with spanner flat drylin® disc drylin® disc – eliminate clearance easily at low cost drylin® disc drylin® - Trapezoidal threaded spindle drylin® - Trapezoidal threaded spindle drylin® - trapezoidal lead screws made from aluminum, coated drylin® - Trapezoidal threaded spindle, Aluminium drylin® - Trapezoidal lead screw spindles with pin drylin® - Trapezoidal threaded spindle with pin drylin® - Trapezoidal lead screw spindles reverse Increased flexibility for format adjustments: counter rotating drylin® lead screws. reverse drylin® Zero backlash screw drives Screw drives with steep thread for quick adjustments. Zero backlash screw drives drylin® steep-threaded nuts For quick adjustments as an alternative to pneumatic or toothed belt. Leadscrews drylin® steep thread DST Lubricant-free steep thread DST higher performance in service life and efficiency Steep thread DST drylin® steep-threaded spindles Lubrication-free threaded spindles with high pitches. Steep-threaded spindles drylin® leadscrew nuts made of SHT linear modules Threaded nuts made of SHT linear modules drylin® leadscrew nuts made of SHT linear modules drylin® leadscrew nuts made of SLW linear modules Threaded nuts made of SLW linear modules drylin® leadscrew nuts made of SLW linear modules drylin® leadscrewsstorage Anodized aluminum bearing blocks of iglidur® L250. Design your own linear table. Leadscrewsstorage Floating bearing block for lead screws with ball bearing Useful extension to the drylin® construction kit. Floating bearing block for lead screws with ball bearing drylin® lead screw nut retainer Conveniently use srews to standard lead screw nuts with nut retainers drylin® lead screw nut retainer drylin® spherical trapezoidal lead screw nut To compensate for angular errors in screwed on plates. Spherical trapezoidal lead screw nut drylin® spherical lead screw nut with flange housing spherical trapezoidal lead screw nut, which permits continuous angle adjustments. drylin® leadscre nut with flange housing drylin® spherical lead screw nut with pillow block bearing Spherical lead screw nut with pillow block bearing continuous angle adjustments. drylin® lead screw nut with pillow block bearings drylin® quick-release nut – Fast Forward Fast forward mechanism: A combination of accurate positioning and quick manual adjustment with trapezoidal lead screw nuts. Quick release mechanism drylin® clamping rings drylin® clamping rings - flexible even down to the finest of details, made of coated aluminum. drylin® clamping rings drylin® trapezoidal lead screw nut - cylindrical nuts with right-hand thread Trapezoidal lead screw nuts made from lubricant-free iglidur® W300, J, J350 and A180. drylin® - trapezoidal leadscrew nuts - WSRM, JSRM, J350SRM and A180SRM drylin® trapezoidal lead screw nut - cylindrical nuts with left-hand thread Trapezoidal leadscrew nuts made from lubrication-free iglidur® W300 and iglidur® J. drylin® - trapezoidal leadscrew nuts - WSLM and JSLM drylin® trapezoidal lead screw nut - flanged nuts with right-hand thread Trapezoidal lead screw nuts made from lubricant-free iglidur® W300, J, J350 and A180. drylin® - trapezoidal leadscrew nuts - WFRM, JFRM, J350FRM and A180FRM drylin® trapezoidal lead screw nut - flanged nuts with left-hand thread Trapezoidal leadscrew nuts made from lubrication-free iglidur® W300 and iglidur® J. drylin® - trapezoidal leadscrew nuts - WFLM and JFLM drylin® Anti-backlash nuts Trapezoidal leadscrew nuts with reduced bearing clearance. Anti-backlash nuts drylin® split lead screw nuts Split lead screw nuts for easy assembly. drylin® split lead screw nut drylin® leadscrew nut - two start two-start lead screws, double stroke in addition to the usual trapezoidal leadscrew nuts. drylin® two-start leadscrew nut drylin® miniature nuts Screw drives ,iniatur lead screw nuts, small sizes. Miniature nuts small sizes drylin® lead screw nuts with spanner flat Ideal transmission of the torque through form fit. drylin® lead screw nuts with spanner flat drylin® disc drylin® disc – eliminate clearance easily at low cost drylin® disc drylin® - Trapezoidal threaded spindle drylin® - Trapezoidal threaded spindle drylin® - trapezoidal lead screws made from aluminum, coated drylin® - Trapezoidal threaded spindle, Aluminium drylin® - Trapezoidal lead screw spindles with pin drylin® - Trapezoidal threaded spindle with pin drylin® - Trapezoidal lead screw spindles reverse Increased flexibility for format adjustments: counter rotating drylin® lead screws. reverse drylin® Zero backlash screw drives Screw drives with steep thread for quick adjustments. Zero backlash screw drives drylin® steep-threaded nuts For quick adjustments as an alternative to pneumatic or toothed belt. Leadscrews drylin® steep thread DST Lubricant-free steep thread DST higher performance in service life and efficiency Steep thread DST drylin® steep-threaded spindles Lubrication-free threaded spindles with high pitches. Steep-threaded spindles drylin® leadscrew nuts made of SHT linear modules Threaded nuts made of SHT linear modules drylin® leadscrew nuts made of SHT linear modules drylin® leadscrew nuts made of SLW linear modules Threaded nuts made of SLW linear modules drylin® leadscrew nuts made of SLW linear modules drylin® leadscrewsstorage Anodized aluminum bearing blocks of iglidur® L250. Design your own linear table. Leadscrewsstorage Floating bearing block for lead screws with ball bearing Useful extension to the drylin® construction kit. Floating bearing block for lead screws with ball bearing drylin® lead screw nut retainer Conveniently use srews to standard lead screw nuts with nut retainers drylin® lead screw nut retainer drylin® spherical trapezoidal lead screw nut To compensate for angular errors in screwed on plates. Spherical trapezoidal lead screw nut drylin® spherical lead screw nut with flange housing spherical trapezoidal lead screw nut, which permits continuous angle adjustments. drylin® leadscre nut with flange housing drylin® spherical lead screw nut with pillow block bearing Spherical lead screw nut with pillow block bearing continuous angle adjustments. drylin® lead screw nut with pillow block bearings drylin® quick-release nut – Fast Forward Fast forward mechanism: A combination of accurate positioning and quick manual adjustment with trapezoidal lead screw nuts. Quick release mechanism drylin® clamping rings drylin® clamping rings - flexible even down to the finest of details, made of coated aluminum. drylin® clamping rings Lead-free - According to (RoHS) 2002/95/EG Standards and Certificates

Steel C35Pb. Gunmetal Rg7. Plastic PA6.6 with MoS2). ISO trapezoidal thread based on DIN 103. Steel nuts for adjustments during manual operation and as fastening nuts. Not advised for use with motorised drives due to the steelsteel material combination. Gunmetal nuts for motion drives with low and medium speed. By insufficient lubrication, gunmetal trapezoidal thread nuts on steel spindles have good dryrunning properties. Plastic nuts for lownoise motion drives. Good dryrunning properties. Tolerance class 7H.

Table for manual using or outside motorization Guided on ball bushings Guide tables without transmission These tables are used for manual movement or for external drives. The end plates are tapped in the center to optionally receive a hydraulic shock absorber or stroke adjustment. On request, a position clamping is available (option /BP0* on leadscrew tables). Range of linear tables with cylinder or screw transmission These tables exist, in the same dimensions, in different versions – suitable for pneumatic cylinder Type 307 – with trapezoidal screw for electric drive Type 308 – with ball screw for electric drive Type 308 – with trapezoidal screw for manual drive Type 309

Positioning table for electric motor Guided by 2 rods on ball bushings (bronze bearings on request) Motor adaptation for linear table These leadscrew tables are delivered without motor, but the adaptation of your motor can be done by us. Some adaptations are standard, especially for standard motors (NEMA17 or NEMA23), if the dimensions of your motor are not listed, contact us to check the feasibility of your motor adaptation from our rough parts. Trapezoidal screw tables for motor The trapezoidal screw is irreversible and the axial precision of these tables is <0.15 mm (in practice 0.02 to 0.10 mm). The maxi stroke is 750 mm, and any intermediate stroke can be produced. For a XY cross table, the tables are mounted on each other directly by the body with option 308922* (smooth holes are made in the body of a table). For more precise positioning applications, these tables are available with ballscrew.

Manual table with double carriage with reversed step (the 2 carriages move away or get closer) Driving by leadscrew Guided by 2 rods Interest of table with reversed step The two carriages move away or get closer symmetrically during the rotation of the trapezoidal screw thanks to right and lefthand thread, this allows for example to adjust the spacing of the outer guides of a conveyor according to the type of product transported. Precision and robustness of right and lefthand thread table The guidance is provided by 2 rods on 4 calibrated bronze bearings (reduced play) or 4 ball bushings for guidance without clearance. The guide length of long body tables (309N/P) allows to accept large loads and torques. The axial positioning accuracy of these tables is <0.15 mm (in practice 0.02 to 0.10 mm). But the blocking in position is done on the carriage, by pressure on a guide rod, so as to remove the axial play of the nut of the trapezoidal screw after blocking

Positioning table for electric motor Guided by 2 rods on ball bushings Motor adaptation on linear table These ballscrew tables are delivered without motor, but the adaptation of your motor can be done by us. Some adaptations are standard, especially for standard motors (NEMA17 or NEMA23), if the dimensions of your motor are not listed, contact us to check the feasibility of your motor adaptation from our rough parts. Tables with ballscrew for motor The ballscrew is reversible and the axial precision of these tables is <0.07 mm. The maxi stroke is 400 mm, and any intermediate stroke can be produced. For a XY cross table, the tables are mounted on each other directly by the body with option 308922* (smooth holes are made in the body of a table). For less precise positioning applications, these tables are available with trapezoidal screw.

Lifting table for electric motor Fixing with its reinforced end for vertical using Drived by ballscrew or leadscrew Guided by 2 rods on ball bushings (or plain bearings in leadscrew version) Motor adaptation for lifting table These lifting tables are delivered without motor, but the adaptation of your motor can be done by us. Some adaptations are standard, especially for standard motors (NEMA17 or NEMA23), if the dimensions of your motor are not listed, contact us to check the feasibility of your motor adaptation from our rough parts. Presentation of the lifting tables to be motorized The trapezoidal screw version is irreversible and the axial precision is <0.15 mm (in practice 0,02 to 0,10 mm). The ballscrew version is reversible and the axial accuracy is <0.07 mm. The maxi stroke is 300 mm, and any intermediate stroke can be produced. Assembly of tables in XZ, YZ or XYZ systems For a crossed table XZ

These bearing blocks permits to realize linear tables with 2 guide rods. Guided by 4 ball bushings and protected by 4 wiper seals. Quadruple bearings or bearing blocks These bearing blocks (or quadruple bearings blocks) permits to realize linear tables with 2 guide rods. Guided on 4 ball bushings and protected by 4 wiper seals. The housing is in anodized aluminium. In option, for dusty environment additionnals wipers in nitrile (/RNI) or polyurethane (/RPU). With 2 guide rods in hardened steel, you can easily make a precision linear table that will withstand significant torques and loads (according to the length of the rods). These blocks are interchangeable with the bodies of Type 306 linear tables, Type 309 trapezoidal screw tables, Type 308 ball screw tables and Type 307 pneumatic cylinder tables. They can therefore be the basis for a special execution of these products.

Manual positioning table drived by lead screw Guided by 2 rods on bronze bearings or ball bushings Precision manual tables The guidance is ensured by 2 rods on 4 calibrated bronze bearings (reduced play) or 4 ball bushings for guidance without play. The guide length of long body tables (309L/M) allows to accept large loads and torques. The axial positioning accuracy of these tables is <0.15 mm (in practice 0.02 to 0.10 mm). But the blocking in position is done on the carriage, by pressure on a guide rod, so as to remove the axial play of the nut of the trapezoidal screw after blocking. Manual crossed tables XY or YZ For the creation of XY crossed table, the tables are mounted one on the other directly by the body (long body version only) with the option 308922 * making smooth holes in the body of a table. To combine 2 tables in YZ, it is preferable to use a lifting table for the Z axis, mounted by its end on the body of the horizontal table.

Economical manual positioning table drived by leadscrew. Actuated by grip knob. Guided by 2 rods on bronze bearings. Using of economical manual tables Acting is done by a grip knob supplied with the table. Maxi stroke is 100 mm for size 0, and 200 mm for sizes 1 and 2. Any nonstandard intermediate stroke can be produced. The locking in position is done on the trapezoidal screw, either in position B1 (above the front plate) or in position B2 (at the end of the end plate) depending on the access and the space available. The position is visualized by a mechanical indicator or by ruler on the base plate. The fixing on the frame is done by the 2 end plates (laminated holes) or by the end plate in « Z axis » version for vertical applications. The positioning accuracy of economical manual tables The axial positioning accuracy of these tables is <0.20 mm (in practice 0.05 to 0.15 mm), because the axial play is largely eliminated after locking in position

When that extra dose of torque is necessary. Our planetary, spur and special gearheads perfectly compliment our motors. When performance is required at high torque levels and correspondingly low speeds, maxon precision gearheads are in their element. In addition to a wide standard range of spur and planetary gearheads, maxon motor also excels in providing customized solutions, tailored to the customer's requirements. Cutting-edge materials and manufacturing processes are used (e.g. CIM/MIM). The gearheads are adapted to the desired motors on site in the supplying plant, further improving the gearhead performance. maxon spur gearheads Spur gearheads are suitable for low torques. The gearheads consist of one or more stages. One stage represents the pairing of two cogwheels. The first toothed gear (pinion) is mounted directly on the motor shaft. The bearing of the output shaft is usually made of sintered materials. Attractively priced Output torque of up to 2 Nm Reduction ratio of 6:1 to 5752:1 Low noise level High efficiency maxon planetary gearhead Planetary gearheads are suitable for transferring high torque. The larger gearheads are normally equipped with ball bearings at the gearhead output. Torque up to 180 Nm Reduction ratio of 4:1 to 6285:1 High power in a small space maxon Koaxdrive The quiet maxon Koaxdrive gearhead combines worm and planetary gearheads. The signature characteristic of the drive is its unusually quiet running, even under heavy loads. Quiet High reduction ratio in the first stage Combined with maxon EC motors, ideal for medical technology. maxon spindle drive Spindle drives transfer the power generated by the motor into linear feed rate and feed force. The output shaft's bearings can absorb highest axial loads. Compact design due to direct integration of the spindle Comprises planetary gearhead with radial and axial bearings Designed for high forces and linear feed rates Wide range of spindles to suite any applicationWith integrated axial bearing for high axial loads: metric spindles, ball screws and trapezoidal screws are available.

When that extra dose of torque is necessary. Our planetary, spur and special gearheads perfectly compliment our motors. When performance is required at high torque levels and correspondingly low speeds, maxon precision gearheads are in their element. In addition to a wide standard range of spur and planetary gearheads, maxon motor also excels in providing customized solutions, tailored to the customer's requirements. Cutting-edge materials and manufacturing processes are used (e.g. CIM/MIM). The gearheads are adapted to the desired motors on site in the supplying plant, further improving the gearhead performance. maxon spur gearheads Spur gearheads are suitable for low torques. The gearheads consist of one or more stages. One stage represents the pairing of two cogwheels. The first toothed gear (pinion) is mounted directly on the motor shaft. The bearing of the output shaft is usually made of sintered materials. Attractively priced Output torque of up to 2 Nm Reduction ratio of 6:1 to 5752:1 Low noise level High efficiency maxon planetary gearhead Planetary gearheads are suitable for transferring high torque. The larger gearheads are normally equipped with ball bearings at the gearhead output. Torque up to 180 Nm Reduction ratio of 4:1 to 6285:1 High power in a small space maxon Koaxdrive The quiet maxon Koaxdrive gearhead combines worm and planetary gearheads. The signature characteristic of the drive is its unusually quiet running, even under heavy loads. Quiet High reduction ratio in the first stage Combined with maxon EC motors, ideal for medical technology. maxon spindle drive Spindle drives transfer the power generated by the motor into linear feed rate and feed force. The output shaft's bearings can absorb highest axial loads. Compact design due to direct integration of the spindle Comprises planetary gearhead with radial and axial bearings Designed for high forces and linear feed rates Wide range of spindles to suite any applicationWith integrated axial bearing for high axial loads: metric spindles, ball screws and trapezoidal screws are available.

USE : Locking Switches and Crossings. ADVANTAGES : Highly safe Equipment in forged steel (doesn't engage the Track Gauge). - Screw stroke : 100 mm - 10 Locking Positions - The Screw is made from hardened steel with a 120° pointed end. (small thread) - Pivoted Rear Shoe - Paint brown or yellow varnish - Overall Length : 40 x 20 x 10 cm - Weight : 5.7 Kg - Reference : 271 OPTIONS Trapezoïdal Threaded Screw (minimum quantity = 20 pcs.) - Ref. 271-FT

precision slides with ball screws or trapezoidal screw drive. - Three sizes – 100, 155 and 225 - Cover variants – sheet or bellows cover - Traversing carriage available in two lengths - Various stepper and servo motors, controllers, special versions such as - Motor deflections via timing belt drive make the precision slides universal can be used and are optionally available with or without motor. - Integrated limit switches (inductive proximity switches) with cable entry or plug connection in the endplate. - Base plate and end plates are made of a surface-treated and high-strength aluminium alloy. - Modular use, e. g. as multi-axis systems

In many areas of mechanical engineering, electromechanical drives are replacing hydraulic units in order to avoid the risk of oil leaking into water or the danger to people from burning liquids. Our electric lifting cylinders have been specially developed for use in hydraulic steel construction. They are suitable as drives for contactors and bridge actuation, as well as for lock gates and barrages. With our modular system, various designs such as trapezoidal, ball or planetary roller screw drive can be realized. Limit switches for permanent travel or load measurement can be integrated. The drive systems are equipped with environmentally friendly, biodegradable fat filled to meet the strict environmental requirements. They are characterized by a special design adapted to the intended use, a high level of serviceability and versatility. Our electric lifting cylinders form a reliable and sustainable alternative to hydraulic lifting cylinders in various fields of application.