Results for
SPIROL
Germany
SPIROL designs and manufactures specific types of Solid Pins to meet the performance and assembly requirements of common niche applications. These Solid Pins are variations of our standard product either manufactured from specific material, have a specific finish or undergo specific processing to meet performance, corrosion, compatibility and assembly requirements for the specific application. These pre-designed application-specific series of Solid Pins help companies shorten the design cycle to confidently launch their product quickly to the market with a pinning solution that has been tested and proven within their assembly.
Request for a quoteSPIROL
Germany
SPIROL's FH400 Headed Barbed Pin has a series of barbs extending down the entire length of the pin. Headed Barbed Pins are a great replacement for self-tapping screws in plastic assemblies as Barbed Pins are installed into standard moulded (or drilled) holes, they install much faster than screws, and they eliminate issues associated with cross-threaded or skewing during installation. Unlike screws that resist back-out (or loosening) by being tightened to a preset torque, Barbed Pins are retained by the plastic backfilling over the aggressively-designed barbs. The head provides a positive stop and is also used to retain a thin component to a thicker component within an assembly. SPIROL's FH400 Headed Barbed Pins are available in metric diameters ranging from Ø2mm to Ø6mm and inch diameters ranging from Ø.078" (5/64) to Ø.250" (1/4) in low carbon steel and austenitic stainless steel.
Request for a quoteSPIROL
Germany
SPIROL's BP100 Press-N-Lok™ Pin has opposing barbs on each end of the pin and is designed to permanently retain two plastic components to each other such as two halves of a plastic enclosure. Press-N-Lok™ Pins are installed in two stages: First, press the pins into one half of the plastic housing. Next, align the other half of the housing with the exposed pins and press into place. During installation, the plastic will backfill into the area around the barbs resulting in maximum resistance to axial force. SPIROL's Press-N-Lok™ Pins are manufactured from lightweight, lead free aluminium as a standard, and available to order in austenitic stainless steel. BP100 Press-N-Lok™ Pins are available in diameters ranging from 2mm to 4mm.
Request for a quoteSPIROL
Germany
SPIROL's Barbed Pins were created specifically for use in flexible plastics where optimum resistance to axial force is desired. The raised barbs are angled backwards, opposite the direction of insertion. After installation, the plastic will backfill into the area around the barbs resulting in maximum retention. Barbed Pins are ideal for applications requiring high pull-out (tensile) strength, and to prevent disassembly (i.e. tamperproof ). Barbs are not appropriate for brittle plastics or those containing high percentages of fillers. As barbs are a radial feature, they do not resist rotation of two components relative to one another. For this requirement, a straight or helical knurl should be used. All Barbed Pins are provided with a generous pilot to facilitate alignment with the hole and ease installation.
Request for a quoteSPIROL
Germany
SPIROL's FH300 Headed Helical Knurled Pin has the same body style as the KP300 Helical Knurled Pin, with the addition of a head. A Headed Pin is typically used to provide a positive stop or to retain a thin component to a thicker component within an assembly. FH300 Headed Helical Knurled Pins have a flat head, however they are available to order with a round head (RH300) to meet specific application requirements. Similar to the SPIROL Series KP300 Helical Knurled Pin offering, SPIROL's FH300 Headed Helical Knurled Pins are available in metric diameters ranging from Ø2mm to Ø6mm and inch diameters ranging from Ø.078" (5/64) to Ø.250" (1/4) in low carbon steel and austenitic stainless steel.
Request for a quoteSPIROL
Germany
SPIROL's FH200 Headed Straight Knurled Pin has the same body style as the KP200 Straight Knurled Pin, with the addition of a head. A Headed Pin is typically used to provide a positive stop or to retain a thin component to a thicker component within an assembly. FH200 Headed Straight Knurled Pins have a flat head, however they are available to order with a round head (RH200) to meet specific application requirements. Similar to the SPIROL Series KP200 Straight Knurled Pin offering, SPIROL's Series FH200 Headed Straight Knurled Pins are available in metric diameters ranging from Ø2.5mm to Ø6mm and inch diameters ranging from Ø.094" (3/32) to Ø.250" (1/4) in low carbon steel and austenitic stainless steel.
Request for a quoteSPIROL
Germany
SPIROL's KP300 Helical Knurled Pins have helical knurls that span the full length of the pin. The 30° helical knurls cause the pin to rotate during installation into the hole. Helical Knurled Pins offer higher insertion and retention than Straight Knurled Pins. However, KP300 Helical Knurled Pins are not typically recommended when the pin will be subjected to rotational forces as the helical knurl will cause the pin to either "unscrew" itself from the hole or further imbed itself into the hole. KP300 Helical Knurled Pins are available in metric diameters ranging from 2mm to 6mm and in inch diameters ranging from .078" (5/64) to .250" (1/4) in low carbon steel and austenitic stainless steel.
Request for a quoteSPIROL
Germany
SPIROL's KP200 Straight Knurled Pins have straight knurls that span the full length of the pin. Straight Knurled Pins are commonly used in applications where the pin is subjected to rotational forces to transmit torque as well as to resist rotational movement of a mating component. KP200 Straight Knurled Pins are available in metric diameters ranging from 2.5mm to 6mm and in inch diameters ranging from .094" (3/32) to .250" (1/4) in low carbon steel and austenitic stainless steel.
Request for a quoteSPIROL
Germany
SPIROL's Knurled Pins are manufactured with two different knurl types: straight knurls and helical knurls. Unlike a Straight Pin, where retention is provided by the uniform interference between the pin and hole, Knurled Pins are designed to cut into the host. The displacement of the host material into the valleys of the knurls yields more frictional contact area between the Knurled Pin and hole; thus resulting in higher retention. Solid Pins with retention features such as knurls and barbs allow for wider hole tolerances than Solid Pins without retention features (i.e. Straight Pins).
Request for a quoteSPIROL
Germany
SPIROL's FH100 Headed Straight Pin has the same body style as the DP100 Straight Pin, with the addition of a head. A Headed Pin is typically used to provide a positive stop or to retain a thin component to a thicker component within an assembly. FH100 Headed Straight Pins have a flat head, however they are available to order with a round head (RH100) to meet specific application requirements. Similar to the SPIROL Series DP100 Straight Pin offering, SPIROL's Series FH100 Headed Straight Pin is available in metric diameters ranging from Ø2mm to Ø6mm and inch diameters ranging from Ø.078" (5/64) to Ø.250" (1/4).
Request for a quoteSPIROL
Germany
SPIROL's DP100 Straight Pins have smooth outer diameters with no retention features such as knurls or barbs. When used as a press-fit pin, the DP100 Straight Pin is pressed into a hole sized slightly smaller than the diameter of the pin. SPIROL's DP100 Straight Pins are suitable for press fit in host materials that can withstand compression in the order of 0.05mm – 0.08mm (.002” – .003”). The actual recommended hole size for a press-fit depends on the actual host material. It is for this reason that SPIROL Engineering should be consulted for the recommended hole size when DP100 Straight Pins are intended to be press-fit into an assembly. Straight Pins are a great option for applications that do not require the tight tolerances of Machined Solid Pins or Ground Solid Dowels. SPIROL Series DP100 Straight Pin consists of metric diameters ranging from Ø2mm to Ø6mm and inch diameters ranging from Ø.078" (5/64) to Ø.250" (1/4).
Request for a quoteSPIROL
Germany
Offered with or without a head, Straight Pins are distinguished by their uniformity. The chamfered ends are more consistent than tumbled edges—making installation with automatic assembly equipment more reliable. Straight Pins are retained by compressing the host, not the inflexible solid pin. They are suitable for use in plastics for press-fit applications limited to those cases where the host material can withstand compression in the order of 0.05mm – 0.08mm (.002” – .003”). Straight Pins are often used to replace Ground Dowels in applications that do not require the tight tolerances of a Ground Dowel.
Request for a quoteSPIROL
Germany
You can rely on SPIROL to be a design partner to help solve unique problems. Because we supply numerous customers with similar products in similar industries, we are able to meet most needs with our standard products at no additional cost. When the solution falls outside the normal requirements, we have the expertise and engineering personnel to solve those problems. By working with you at the design stage, we will develop a solution that lowers your overall product cost, improves product quality, increases the robustness of your manufacturing process, and gets you to market faster.
Request for a quoteSPIROL
Germany
Series RH600 Twist-Lok™ Pins replace costly screw machined pins and eliminate problematic installation of screws and rivets. The helical knurl minimises stress during installation by rotating as it engages the hinge. Corrosion-resistant material and a rounded burr-free head improve installed appearance. Axial and radial forces induced in the hinge eliminate the tendency for the pin to creep and maintain hinge tension.
Request for a quoteSPIROL
Germany
SPIROL's Series LP500 Latch Pins for Plastics are designed with a barb located under the head with a barb length equal to the width of the outermost section of the assembly. The remaining length of the LP500 Latch Pin is smooth without any other retention features. This allows the LP500 Latch Pin for Plastic to easily align and freely install through all of the holes with a plastic assembly until the barb makes contact with the final hole to securely lock the pin in place. Once fully installed, the handle will pivot freely around the non-barbed end of the stationary pin. The head prevents the LP500 Latch Pin from being over-installed, and enables the pin to be mechanically oriented for automatic installation. Manufactured from lightweight, lead free aluminium, SPIROL's LP500 Latch Pins for Plastics are available in three standard diameters: 3mm, 4mm and 5mm.
Request for a quoteTHERMA THERMOFÜHLER GMBH
Germany
Use: Plug connector for thermocouple and RTD circuits. The solid connector pins guarantee reliable connection under even the most difficult conditions. Mechanical design: • Housing of fibreglass-filled plastic. • Contacts of original thermocouple materials. • Solid connector pins and spring-loaded socket. • Reverse polarity protection by different pin thicknesses. • Central cover attachment for fast installation. • Moulded barriers prevent short-circuits. • Screw terminals enable quick connection.
Request for a quoteTHERMA THERMOFÜHLER GMBH
Germany
Use: Plug connector for thermocouple and RTD circuits. The solid connector pins guarantee reliable connection under even the most difficult conditions. Mechanical design: • Housing of fibreglass-filled plastic. • Contacts of original thermocouple materials. • Solid connector pins and spring-loaded socket. • Reverse polarity protection by different pin thicknesses. • Central cover attachment for fast installation. • Moulded barriers prevent short-circuits. • Screw terminals enable quick connection.
Request for a quoteDo you sell or make similar products?
Sign up to europages and have your products listed
THERMA THERMOFÜHLER GMBH
Germany
Use: Plug connector for thermocouple and RTD circuits. The solid connector pins guarantee reliable connection under even the most difficult conditions. Mechanical design: • Housing of fibreglass-filled plastic. • Contacts of original thermocouple materials. • Solid connector pins and spring-loaded socket. • Reverse polarity protection by different pin thicknesses. • Central cover attachment for fast installation. • Moulded barriers prevent short-circuits. • Screw terminals enable quick connection.
Request for a quoteSCHULZ STANZTECHNIK GMBH
Germany
Design and construction This Schulz ball caster consists of a casing with threaded pin and a top cover as solid turned part, a bearing ball and several support balls. Dimensions The spacing is calculated by dividing the shortest edge length of the object to be transported by 3.5.
Request for a quoteSCHULZ STANZTECHNIK GMBH
Germany
Design and construction This Schulz ball caster consists of a casing with threaded pin and a top cover as solid turned part, a bearing ball and several support balls. Dimensions The spacing is calculated by dividing the shortest edge length of the object to be transported by 3.5.
Request for a quoteSPIROL
Germany
The Series 550 Cosmetic Coiled Pin was designed specifically for cosmetic cases to ensure the perfect balance of strength and flexibility. The 1-1/2 coil construction ensures that the Cosmetic Coiled Pin exerts sufficient radial force to achieve the long-term desired swing torque while protecting the plastic from excessive stresses. The use of SPIROL Series 550 Cosmetic Coiled Pin will simplify your design and manufacturing process. Uniform radial spring force results in controlled hinge movement and a hinge quality that remains consistent over time. Controlled hinge movement is achieved with wider tolerances and lower moulding costs than when a Solid Pin or cut wire is used. Finally, low insertion force and compression of the pin during installation minimises hinge stress and scrap. The net result is the prolonged useful life of the assembly.
Request for a quoteTHERMA THERMOFÜHLER GMBH
Germany
Use: Connector for thermocouple and RTD circuits. The solid connector pins guarantee reliable connection under even the most difficult conditions. The third contact for ground or continuous shield or for three wire RTD´s. Mechanical design: • Housing of fibreglass-filled plastic. • Contacts of original thermocouple materials. • Solid connector pins and spring-loaded socket. • Reverse polarity protection by different pin thicknesses. • Central cover attachment for fast installation. • Moulded barriers prevent short-circuits. • Screw terminals enable quick connection.
Request for a quoteTHERMA THERMOFÜHLER GMBH
Germany
Use: Connector for thermocouple and RTD circuits. The solid connector pins guarantee reliable connection under even the most difficult conditions. Jab-in cover allow easy connection without need cover removal. Mechanical design: • Housing of fibreglass-filled plastic. • Contacts of original thermocouple materials. • Reverse polarity protection by different pin thicknesses. • Central cover attachment for fast installation. • Moulded barriers prevent short-circuits. • Screw terminals enable quick connection.
Request for a quoteSRL
Italy
Frame: Telescopic on two sides made with horizontal tubular steel profiles 40x30mm thickness 20/10 located in the upper and lower parts, anchored to the wall using L-shaped telescopic brackets. Door: made with 40x30mm galvanized steel profiles, 20/10 thickness, assembled by welding. Horizontal tubular crosspiece 30x20mm, filler chosen from our models. Pivot hinges: Composed of a die-cast insert structure within which the cut-resistant solid steel rotation pin with a diameter of 16 mm is controlled. Lock: Mortice lock applied on each door. The lock controls 2 locking tips in solid anti-cut steel, 1 upper and 1 lower. The tips are made of full galvanized steel with a diameter of 16mm and have a stroke of 30mm. Standard anti-drill European safety cylinder is equipped with construction site key + 3 master keys + duplication card. Joint (optional) obtained through mechanical processing of solid steel and carefully welded to the tubulars/crosspieces. The upper
Request for a quoteSRL
Italy
One of the winning features of the Hercules grate is the special PATENTED JOINT which allows for easy and fluid opening of both the internal and external doors, allowing for easy movement of the external shutters. HERCULES 2 – 4 consists of: 4-sided telescopic FRAME, made with 40x30mm galvanized steel vertical profiles, available in 18 variants to best adapt to every construction requirement. GRATED DOOR made with sturdy galvanized steel profiles measuring 60x30mm, while the crosspieces are made of 40x30mm tubing; and as a filler chosen from our aesthetic models. JOINT obtained through mechanical processing of solid steel and carefully welded to the tubulars/crosspieces. The upper joint has a steel nut applied as standard which, in the closed position, embraces the 16mm steel pin inserted on the frame/upper crosspiece. PIVOT HINGES Composed of a die-cast mortise structure within which the cut-resistant solid steel rotation pin, diameter 16 mm, is controlled
Request for a quoteSRL
Italy
DUAL is the innovative COMBINED system between security grate and shutter, which share the SAME FRAME and a SINGLE CLOSING SYSTEM, suitable for elegantly protecting every home DUAL BLIND is composed of: FRAME in galvanized steel on 3 sides made by thick bending. 20/10, with 60mm front fin – Minimum depth 107mm and 20mm H lower crosspiece. GRATED DOOR made with sturdy thick galvanized steel profiles. 20/10: lock holder upright has dimensions of 60x30mm, while the crosspieces and uprights on the hinge side are 40x30mm; and as a filler chosen from our aesthetic models. Steel LOCK without central hook, is equipped with deviators that control 4 solid steel locking pins diam. 18mm, 2 upper and 2 lower (one of which is CUT-PROOF ROTATING) which intercept the closing plates installed on the shutter leaf. ½ DRILL-RESISTANT SAFETY CYLINDER equipped as standard with 1 construction site key for installation, 3 master keys and a card for their duplication.
Request for a quoteSRL
Italy
DUAL is the innovative COMBINED system between security grate and shutter, which share the SAME FRAME and a SINGLE LOCKING SYSTEM, suitable for elegantly protecting every home. DUAL ALL is composed of: FRAME in galvanized steel on 3 sides made by thick bending. 20/10, with 60mm front fin – Minimum depth 97mm and 20mm H lower crossbar. GRATED DOOR made with sturdy thick galvanized steel profiles. 20/10: lock holder upright has dimensions of 60x30mm, while the crosspieces and uprights on the hinge side are 40x30mm; and as a filler chosen from our aesthetic models. Steel LOCK without central hook, is equipped with deviators that control 4 solid steel locking pins diam. 18mm, 2 upper and 2 lower (one of which is CUT-PROOF ROTATING) which intercept the closing plates installed on the shutter leaf. ½ DRILL-RESISTANT SAFETY CYLINDER equipped as standard with 1 construction site key for installation, 3 master keys and a card for their duplication.
Request for a quoteZIMAS ZINCIR VE MAKINA SAN. TIC. A.S
Turkey
https://www.zimaszincir.com.tr/en/products/solid-bearing-pin-chains
Request for a quoteResults for
Solid pin - Import exportNumber of results
29 ProductsCountries
Company type