Penetration test - Import export

Penetrant non-destructive testing method is a system that is used for the detection of cracks in the surfaces of parts. After the material which is going to be subjected to penetrant test is pre-cleaned, it is subjected to penetrant application as dipping or spray. After this process, the material is rinsed and dried. Powder “developer” is applied electrostatically on the dried material. Finally, possible cracks and faults on the material are detected by checking under the UV lamp.

The troubleshooter for energy supply systems in the chip area - available in 4 sizes. Chips and dirt can affect the service life of cables and hoses significantly. With the RX system, igus® offers an extremely tight plastic e-tube that is nonetheless very easy to open. Snap-open in the outer radius A smooth, curved outer contour prevents chips from sticking Injection-molded "sealing lips" all around No holes, cracks, undercuts Series RX40 is IP40 tested (TÜV Saarland) Interior separation and guide trough available Covered pin/hole connection and stops "RBR" version with bending radius on both sides available Typical branches of industry Machine tools All applications in the direct chip sector Applications exposed to dust and dirt General mechanical engineering Dimensions and technical datas RX e-tubes RX32 Inner height hi: 42 mm Inner widths Bi: 80mm Bending radii R: 80 - 250 mm Pitch: 32 mm RX E-Tube RX40 Inner height hi: 52 mm Inner widths Bi: 100 mm bending radii R: 100 - 300 mm Pitch: 40 mm RX E-Tube RX48 Inner height hi: 62 mm Inner widths Bi: 120mm Bending radii R: 120 - 325 mm Pitch: 48 mm RX E-Tube RX56 Inner height hi: 73 mm Inner widths Bi: 140mm Bending radii R: 140 - 350 mm Pitch: 56 mm RX E-Tube RX56 High-temperature plastic version of the chip-proof RX energy tubes from stock - 850°C from 24h RX - from stock against hot chips red dot 2011: honourable mention for RX40 iF-Design-Award for RX e-tubes ESD classification: Electrically conductive ESD/Atex versions on request UL94-V0 classification on request e-tubes available as special design with HT material for 850°C hot chips The troubleshooter for energy supply systems in the chip area - available in 4 sizes. Chips and dirt can affect the service life of cables and hoses significantly. With the RX system, igus® offers an extremely tight plastic e-tube that is nonetheless very easy to open. Snap-open in the outer radius A smooth, curved outer contour prevents chips from sticking Injection-molded "sealing lips" all around No holes, cracks, undercuts Series RX40 is IP40 tested (TÜV Saarland) Interior separation and guide trough available Covered pin/hole connection and stops "RBR" version with bending radius on both sides available Typical branches of industry Machine tools All applications in the direct chip sector Applications exposed to dust and dirt General mechanical engineering Dimensions and technical datas RX e-tubes Chip tests in the igus® laboratory demonstrate the tremendous chip-proof properties of the igus® RX tube. Chip-proof - for all types of chips and applications RX32 Inner height hi: 42 mm Inner widths Bi: 80mm Bending radii R: 80 - 250 mm Pitch: 32 mm RX E-Tube RX40 Inner height hi: 52 mm Inner widths Bi: 100 mm bending radii R: 100 - 300 mm Pitch: 40 mm RX E-Tube RX48 Inner height hi: 62 mm Inner widths Bi: 120mm Bending radii R: 120 - 325 mm Pitch: 48 mm RX E-Tube RX56 Inner height hi: 73 mm Inner widths Bi: 140mm Bending radii R: 140 - 350 mm Pitch: 56 mm RX E-Tube RX56 High-temperature plastic version of the chip-proof RX energy tubes from stock - 850°C from 24h RX - from stock against hot chips Submersion test in water - Various tube types were submerged under water. The new RX tube needs over 30 seconds until it is filled up, thus proving its high leak tightness Y = time in seconds A = igus® products B = competitor Chip penetration test - Various types of tube were exposed to a defined quantity of chips. In the new RX tube, after 80,000 cycles only 0.2 g of chips were found in the interior Y = chip mass [g] A = igus® RX e-tube RX40.100.100 251.900 cycles B = igus® e-tubes 68.10.100.0 256.132 cycles C = test tube 01 250.907 cycles D = test tube 02* 2.600 cycles *Teststop after 2.600 cycles E = igus® products F = competitor E-Chain® selection aids You can find the right E-Chain® quickly by entering concrete parameters and with the aid of a comparison table. Productfinder Assembly instruction Dismantling / assembling a cover, replacing a chain link and assembling / inserting the RX tube. Assembly instruction Configure interior separation Define cables, select chain and configure interior separation. Now also for RX tubes! Interior separation configurator Application examples Applications in various industrial sectors. RX tubes Series RX - new chip-proof design, small pitch, removable cover 1 Chip-proof design without undercuts and edges 2 Excentric locking 3 Material igumid G 4 rounded shape 5 covered pin/hole connection RX tubes IP tested Technical report TÜV NORD red dot 2011: honourable mention for RX40 iF-Design-Award for RX e-tubes ESD classification: Electrically conductive ESD/Atex versions on request UL94-V0 classification on request e-tubes available as special design with HT material for 850°C hot chips

Our specialists have vast knowledge and many years of experience in non-destructive testing (NDT) of welding seams, welding constructions, pressure vessels, containers, equipment and plants. We use and offer the following testing procedures for that purpose: X-rays RT Dye penetrant testing PT Visual inspection VT Material testing/ Positive Material Identification PMI Helium leakage testing LT Riboflavin test Pressure tests of up to max. 1000 bar Surface roughness testing Ra/Rz Ferrit measurement Fe Wall thickness measurement Video endoscopy Pressure-loss test (liquid) With KASAG, you remain on the safe side.

We maintain quality assurance systems, such as iso 9001: 2009, iso 18001-2004 and iso 14001-2005. KIGEMA possesses a laboratory allowing testing the mechanical properties of products like hardness, elongation, and micrometer. KIGEMA also conducts penetration and ultrasonic tests and issues certificates of conformity with EN 10204-2.2, 2.3, 3.1B. Additionally, the company has an air-conditioned measuring room equipped with High-quality measuring equipment, which is regularly calibrated. The measuring equipment includes: calipers, altimeter, depth calipers, inside micrometers, bore gauges, outside micrometer and roughness tester.

DRIVE NDT is a cloud-based management software which integrates all NDT inspection methods and associated processes into a single system. With DRIVE NDT you can organize and control the complete NDT job workflow including individual test reports, staff, customer and device management, and much more. One solution for all NDT inspection methods Radiographic Testing (RT-D, RT-F, CT) Ultrasonic Testing (UT-PA, UT-TOFD, UT-WD) Visual Testing (VT) Electromagnetic Testing (ET) Magnetic Particle Testing (MT) Liquid Penetrant Testing (PT) Acoustic Emission Testing (AT) Acoustic Resonance Testing (ART) Infrared/Thermal Testing (IR/TT) Leak Testing (LT) Optical Methods (OM) ...

Iron Construction Thermal INnsulation WaterProofing Deking Assembly Disassembly stairs Swimming Pool Equipment IRON CONSTRUCTION The core of the pool itself is constructed of steel profiles of different dimensions. The bottom of the pool is lined with HVL 4mm thick while the sides are HVL 3mm thick. The entire construction is professionally welded with sealing welds, tested with penetrants and painted in color as desired. THERMAL INSULATION The sides of the pool are lined with 50mm sandwich panels. The bottom of the pool is lined with 50 mm striroporom which is covered with plasticized ribbed sheet metal in the color of the panel. There is a possibility to order colors and designs as desired. DEKING For decking on the coastal part and around the entire swimming part of the pool, we used "Siberian Larch" wood, which is used all over the world to line the pool due to its properties next to water surfaces. Wood is varnished to receive gloss.