Industrial fan spare - Import export

In the fluid dynamics laboratory of our Wasserburg competence centre, we design new fan wheels and turbines and optimise existing systems for performance, energy efficiency and noise emissions. We also develop complete systems of wheels with power units. Our range of tests includes suction operation, pressure operation and also unpressurised measurements. Revolutions up to 40,000 r/min and diameters of up to 250mm are possible. In our prototype department, we are able to simulate or modify the environmental circumstances of the fan wheels or turbines, thus achieving optimal operational conditions. Furthermore, we carry out mould-flow analysis, use ANSYS from external partners for the flow simulation and establish the fault probability and fault effect with FPFEs. New: Development of blower systems and optimization of ventilation systems.

Ceiling fans for the recovery of stratified heat in the ceiling Ceiling fans with DT protection casing can be used to recover the stratified heat on the roof in winter, using the fan in winter allows us to save energy up to 30% Its use can be commercial and / or industrial and its installation can be on ceilings from 4m to 9m in height. The fans can be mounted individually or in groups with their corresponding speed regulator.

Ceiling fans from 4 to 7m in diameter This type of fan provides significant energy savings and is characterized by having large diameter blades that generate an air flow of 96,810 to 529,000 m3/h. They are suitable for installation in any type of premises with ceilings from 4m to 12m high. Winter operation: Its function is to lower and homogenize the stratified hot air on the ceiling, thus reducing the heating needs of the room or premises. Summer operation Decrease in sensitive temperature around 4-6 ºC

Ceiling fans to cool in summer and save in winter DVW ceiling fans allow them to be used to ventilate in the summer and recover the stratified heat on the ceiling in winter, using the fan in winter allows us to save energy of up to 30%. Its use can be at a domestic, commercial and / or industrial level and its installation can be on ceilings from 2.3m to 10m high. The fans can be individually assembled with their corresponding speed regulator or up to 10 units can be grouped using our model RV10 electrical panel with regulator.

High flow wall fans for extraction and/or ventilation This type of fans provide significant air flows for the extraction and/or ventilation of industrial, livestock or agricultural premises. Main features - Air flow from 21,000 m3/h to 39,800 m3/h - Structure and overpressure slats in galvanized steel to avoid premature corrosion. - Propellers made of AISI 430 BA stainless steel. - High quality bearings. - IP-55 three-phase electric motor - V-belts. - Transmission pulleys made of magnesium aluminum. - Engine support with tensioner. - Side inserts for easy transport.

3m diameter ceiling fan with remote control and reversible MEGA AXIAL 3000 BRUSHLESS ceiling fans can be used to recover the stratified heat on the ceiling during winter and ventilate in summer, using the fan in winter allows us energy savings of up to 30%. Its use can be commercial and / or industrial and its installation can be in ceilings from 4m to 10m in height. The fans can be mounted individually with their remote control.

Since the impellers are made of aluminium as areas of usage gas plants and acidic places preferred. Aspiration of smoke, iron foundry, cement plants, and paper mills Aspiration of moist and dusty air Industrial buildings, animal farms, greenhouses, garages, sport centers, and parks etc.

EFKC filtered shelter fans are used to supply fresh air. It can be used in two different positions thanks to the by-pass cell. Normally, the air is sent indoors only by passing through the G4 Filter. When we want the air to be cleaned, it is passed through the G4 cassette filter, active carbon cassette filter and M6 cassette filter, which is more sensitive than the coarse filter, and sent indoors. By-pass air dams are made with a sliding system.

These fans have low heights, they are suitable for car parks with a height of less than 2.4m or with cassette entrances. They can operate continuously for 2 hours at 300 and 400 °C. F400-120 / F300-120

These fans, which are used in the ventilation of closed environments, can operate without problems with their high performance, they can operate even at high temperatures since the engine is outside of the air flow.

The propellers of AKAP sleeve fans, which can meet high air flow rates and high pressure losses, are made of aluminum raw material and they provide the chance to change the flow and pressure by adjusting the blade angles. They can be produced with a motor that can withstand temperatures of 200, 300, 400 °C for 120 minutes upon request.

USAGE AREAS -It is used in the heating industry for burning solid and liquid fuels in boilers and providing secondary air in a controlled manner. -In the ventilation of closed environments -In industrial machinery belonging to the jewelery sector -in the textile industry -In mines and mushroom farms -In plastic injection machines -In the combustion air supply of gas, diesel burners -In humid and humid environments -In the greenhouse industry -In chicken coops -Used in many areas of the manufacturing industry

Serie LPE HELICAL FANS FOR WALL The LPE serie’s fans, present constructive characteristics that allow both the utilization in the industrial applications and the installations in the tertiary environments (workshops, stores, breedings, glasshouses) where there is the real necessity of the employment of a fan with easy installation, low consumptions, and reduced noise pressure levels.

manufacturer of all types of Axial fans

ERF-CAT double suction centrifugal cell fans are produced in different sizes between 1.000m³/h and 20.000 m³/h flow rates. Cell panels are 20 mm thick and 70 kg/m³ density rock wool insulated. They provide maximum efficiency with low energy and vibration-free operation.

The fan and cooling specialist SEPA EUROPE unveils a true innovation this year: The RaAxial fan. This created term is a combination of the words radial and axial. The microfan with its dimensions of 17x17x4.5mm is ideal for compact, embedded applications and offers numerous possibilities, e.g. as an axial fan for the ventilation of housings or as a radial fan for blowing air onto the heat sink. A tailor-made „Kühligel®“ has already been developed for the latter which makes the cooling of hotspots child’s play when space is limited. Reliability has top priority at SEPA EUROPE. For this very reason the new fan is equipped with the tried and tested Magfix® bearing system. The life expectancy at 40 °C is 210 000 h (MTBF) or 40 000 h (L10).

*Made Of Galvanized Metal Plate *Wihtout Motor *Air System Easily With The Help Of Rectangular Fans *Designed For The Needs Of Middle Upper Aspiration Capacity *With The Help Of The Maintenance Covers, Engine And Fan Can Be Fixed Without Removing The Equipment.

By mounting an axial fan, the effectiveness of the new Kühligel® can be increased considerably. Fanless solutions require a lot of space. They are heavy and expensive. For cooling with active coolers by SEPA EUROPE however, the new Kühligels are not only small and light but also extremely inexpensive. Thanks to intensive development work, SEPA EUROPE was able to construct a heat sink that enables fan mounting without extensive reworking using conventional screws. The choice of the suitable fan (size, sleeve or ball bearings, 5, 12, or 24 VDC, tacho, connector) enables the best possible combination that is required for the application in question. The fans used have a MTBF of up to 350000h (40°C) and thus meet the highest requirements. Thanks to its light weight, the Kühligel® can usually be mounted using double-sided adhesive heat conduction pads (TCTxx) or thermally conductive two-component adhesive (Hernon 746) which are both available from the SEPA EUROPE product range.

Thanks to the intelligent combination of DC fans with a fully integrated AC/DC converter, AC fans can now be operated at speeds that are independent of the power frequency. Up to 4500 rpm can be realized and the flow rate significantly increased if required. The EC generation in the dimensions 80mm to 280mm and with several different speeds replaces the previous AC fans in situtations where there is no DC voltage available and requires less power in the process. The previous AC fans can be replaced without restriction as the EC fans have identical dimensions and thickness. The versions that are smaller than 180mm have a wide-range input and can be connected without problem, worldwide to all AC voltage networks without need for further adaptation. This is underlined by the UL approval of the entire fan series.

USAGE AREAS * In marble machines * In the supply of combustion air for gas, diesel burners * In the transfer of residues such as dust, clippings, etc. * In the storage of granules and particles * In blow-drying machines * In textile machines-placket spreading machines * At exhaust metering stations * In extruder machines * Can be used safely in industry for wide purpose

The fan and cooling specialist SEPA EUROPE has now added three further models to its slimline radial fan series. The latest additions impress with their compact dimensions of 38 x 40 x 5 mm, 54 x 52 x 6 mm and 45 x 45 x 4 mm and have more than deserved the name „slimline“. All fans are equipped with the reliable Magfix sleeve bearings and have a service life of 210 000 h (MTBF) and 40 000 h /L10) at 40 °C. The PWM input in combination with the tacho output enables the speed to be controlled and monitored. It is not obvious at first glance, but the Model HY45AB05PNK00A tops with a pressure of 143 Pa. The new models will be included in the standard range and will therefore be available shortly from stock. SEPA EUROPE specializes in customized cooling solutions. Thanks to over 25 years of experience, SEPA EUROPE can offer you the appropriate solution for virtually every task.

Chip cooling with the aid of heat sinks usually requires a lot of space and is not only heavy but also expensive. The specialists at SEPA EUROPE have developed a chip cooler with minimum space requirements for compact designs. The core component of the compact cooler is the ultra-flat blower HY40H that is combined with a Kühligel® of pure aluminium. The special feature of the new cooling solution is its variability which means that the size and shape of the heat sink can be freely chosen. Users can thus assemble the cooler to optimally fulfil their requirements. With a thermal resistance of a mere 2.5 K/W, the new chip cooler withstands a power dissipation of up to 15 W and in doing so guarantees the operational safety of the entire embedded system. The blower is equipped with the highly durable Magfix® sleeve bearing and has an impressive service life expectancy of von 210 000 h (MTBF) at 40 °C.

manufacturer of all types of roof mounted axial fans

Passive cooling solutions are usually too big. Small active heat sinks are the ideal solution. Stable light colours, a high life expectancy and low energy requirements are the unbeatable advantages of LED technology. However, whereas the energetic superiority comes virtually automatically, considerable investment must be made in thermal management to fulfil the demands on the colour values and service life. Only well cooled diodes can keep what they have promised in the long run. For optimum thermal management, SEPA EUROPE offers not only passive cooling solutions but also active heat sinks. Active cooling concepts usually provide the ideal solution when space is a problem. They are smaller and lighter, can attain the desired service life, are attractively priced and find space virtually everywhere. SEPA EUROPE already supplies its customers with fans that are adapted to the application in question and in some cases with special waterproof fans.

SEPA EUROPE offers a 40 mm frameless fan especially for embedded systems. It is 10 mm high and provides a compact solution for chip cooling when used in combination with the appropriate heat sink. In addition to the 50 mm frameless fan which is already on the market, the new round 40 mm fan is also a much sought-after model for embedded systems. This is because many standard cooling solutions in this business sector are based on the 40 x 10 mm fan. Strictly speaking, the 40 mm fan has a rotor diameter of 37 mm. The version offered by SEPA EUROPE is equipped with two ball bearings and can boast a remarkable service life of 70.000 h at a temperature of 40°C. In addition to an impulse output for speed monitoring, it also has a PWM input for speed setting in the range of approx. 35 – 100% of the nominal speed. In conjunction with the power block pin-fin heat sink, this virtually silent fan with 22 dB(A) is also available ready for connection in the „Kühligel“ version.

Collecting dust Fume/gas elimination Handling fine grained material (marble dust, granule, plastique etc.) At printing houses, different factories such as textile,

Inspired by customer inquiries, SEPA EUROPE has developed a new, modular assembly for the efficient cooling of chips. The core component is a SEPA axial fan that is mounted on a 40 mm pure aluminium heat sink – a so-called Kühligel®. It is equipped with a finger guard and a double-sided adhesive heat pad for screwless mounting on the housing or inside the device. Thanks to the compact design, the light weight and the screwless mounting, this assembly enables accurate positioning and thus effective cooling of the hot spot. The chip cooler HXB40FGK is equipped with a high precision ball bearing and can be used at ambient temperatures between -10 and +85 °C thus opening up a wide range of application possibilities. A further advantage is the long service life of the fan with 350 000 h (MTBF) at 40°C. The chip cooler assembly HXB40FGK is supplied as a standard component. It can however, be customized.

SEPA EUROPE, the experts for customized cooling solutions meets the highest expectations with its wide range of guards for axial fans. Modern high-performance fans operate at high speeds which increase the risk of injury. To enhance safety, SEPA EUROPE offers guards for axial fans in every required dimension. The well-designed guards of SEPA EUROPE are not only extremely stable but also improve the appearance of each fan. The high-quality surface (chrome-plated, powder-coated, zinc-plated or pure stainless steel V2A or V4A) stands for a longer service life and extensive protection against corrosion. We perfect the product with excellent finishing and a flawless surface without sharp edges. Additional advantage: The guards of SEPA EUROPE are aerodynamically optimized so that the fans can operate with optimum efficiency. A further advantage is the simple mounting by screwing to the fan.