Fans serie - Import export

Bathroom fans are the most popular and affordable modern solution for the removal of moisture from wet rooms and the prevention of mold and fungus formation. MM Series — Bathroom and WC fans featuring modern design, high airflow rate and uncompromising quality. These fans provide continuous or interrupted ventilation in the sanitary facilities at extremely low power consumption. They can be used to purge air from small and mediumsized residential, office and commercial premises or as heat exchangers between adjacent premises. The fans are mounted on walls, ceilings and suspended ceilings and are attached to air ducts or pipes of the building’s ventilation system with connection diameters 100 mm, 120 mm and 150 mm. Safety The MM Series fans are made of highquality and harmless materials, and they comply with noise and fire safety standards. The protection degree of the builtin electric motor is IP 24, IP X4, IP X5 and IP 56 which enables the fan to normally operate in high humidity

Due to the three-blade piston profile and the optimized housing shape, the 3RV Series fans are characterized by their high efficiency, low noise level and compact dimensions. The massive pistons cause a very quiet run of the blower.

The TTV series fans follows one specific aim with each new development and that is to achieve the utmost economic efficiency with the highest flexibility using as little modules as possible. In more simple terms, instead of an abundance of appliances use an abundance of applications. The on-site flexibility on this concept of the platform is increased, due to the fan application being interchangeable even at the shortest notice. The end result is with even one fan, you’re able to fulfill a variety of tasks that would normally have needed many appliances. There are many practical advantages such as easy maintenance, easy storage, splash waterproof, and for higher economic efficiency they are stackable.

TDS 50 Electric Fan Heater The TDS 50 electric heater provides a heating performance between 4.5 kW and 9 kW in 3 stages (stage 1 only fan). Furthermore the TDS 50 has an integrated thermostat for continously adjusting the desired temperature. In comparison to direct fired gas or oil heaters, the electric fan heaters of the TDS series dont consume oxygen or produce combustion gases. Because of that this devices can be used everywhere, in particular for temperature control of unheated interiors. Benefits in pratice: 100% TROTEC - development, design, production Multistage temperature control Integrated room thermostat for constant, cosy warmth Overheat protection Fan motor with thermal protection Condensation-free heating - no oxygen consumption - because of that the TDS 50 is suitable for uses in enclosed rooms Wall and ceiling bracket available - mounting is available as an accessory

The axial fan model TTV 7000 is a specially designed solution for industries requiring film and event services. The TTV platform is placed at the centre of the axial fan. The principal aim of the TTV series of fans is to provide highest of performances, delivering economically and achieving high levels of flexibility. The TTV series aims at catering to more applications using lesser tools. The on-site flexibility is enhanced due to the fact that applications can be changed as and when desired on-site to meet the ever demanding industry. Multiple tasks can be addressed by just one fan fitted into the system. The system is also protected from splash water, it can be stacked over to save space and is extremely economic and delivers exceedingly high levels of efficiency.

ELECTRIC HEATER FAN TDS 10Small firebrand with impressive inner values There are many electric heater fans – but only one original Trotec TDS series. Distinctively recognizable by the logo printed on the side, even the smallest electric heater fan of our TDS series presents itself to you in markedly good shape. And not only on the surface. A second glance may well be worthwhile, in every respect, little by little, can add up to a great difference! Only the TDS electric heater fans from Trotec are equipped with two convenient attachment screws mounted to the sides in order to accommodate the optionally available wall and ceiling holders. With the electric heater fan TDS 10, the desired temperature can easily be adjusted via an infinitely variable thermostat, which automatically switches the heating elements on as needed in addition to the permanent fan to save energy.

IDS 80 OIL HEATER FANThe robust IDS 80 oil fan heater for fast, uncomplicated heating - mobile heating power on wheels This oil heater fan of the IDS pro series is especially suitable for longer heating applications, because it is possible to connect an external oil tank in addition to the integrated fuel container. The double-walled housing with protective coating ideally absorbs sound, minimizes surface temperature and thus the risk of injuries. Electronic flame trap, safety thermostat for overheating protection and fully automatic after-cooling are further safety measures. The carriage and big wheels provide sufficient flexibility. Especially when working on building sites, the location can simply be changed. The oil heater fan IDS 80 further comes with a connection facility for an air transport hose and a two-way hose distributor.

OIL HEATER FAN IDE 20Flexible all-rounder for a wide range of heating applications: the ultramobile oil fan heater IDE 20 Hot air in a trice at a low price: The smallest oil heater fan of the IDE series from Trotec comes up trumps if you are looking for a compact and low-priced yet reliable oil heating solution for flexible heating applications. Whether in workshops, warehouses, production zones or on construction sites – with a heating capacity of 20 kW the IDE 20 confidently generates clean and dry hot air in quantities of up to 600 m³/h. Even longer outdoor applications present no obstacle to the oil heater fan IDE 20, because it is provided with a durable housing made of doubly coated material, borne by a smooth-running carriage construction with cable holders and installed fuel tank. When employing the optionally available flue gas discharge, this heating device can also be flexibly used for the fully automatic heating of closed rooms.

Features High chemical-resistant rotating cleaning nozzles. Solid stream (ES series) or flat fan-shaped spray pattern (ESV series). Compact and simple design. Rotation is driven solely by the flow of the cleaning fluid. Clean design with little dripping from the nozzle tip even when installed upward. Applications Cleaning by volume of spray flow, not by spray impact Cleaning of tanks and filling machines

The term inline filter refers to an expandable, bolted, modular system. Depending on requirements, appropriate filter and air injection sections are connected together in series. The capacity range extends from approx. 10,000–300,000 m³/h. RS / RX filter The RS / RX series are a proven, expandable, modular system with low-pressure purge-air cleaning. Depending on requirements, appropriate filter and air injection sections are connected together in series. The capacity range extends from approx. 20,000–300,000 m³/h. RS / RX filters are suitable only for vacuum and positive pressure operation. The housing parts are usually made of 2 mm thick galvanised sheet steel. A thicker material in a painted execution as well as in stainless steel is also optionally available. The RS / RX series is 2.85 m wide. Filter hose lengths of 3 m (standard) and 4 m are available for this. The RSEC series has been designed for smaller air quantities and for above-roof installation. This series has a housing width of 2.4 m and 2 m-long filter hoses. The filter hoses are manufactured from polyester needle felt; the filtering direction is from the outside inwards. Filter cartridges and filter tubes are alternatively possible. The filter hoses are cleaned off using the material-preserving low-pressure purge-air system. The purging trolley inside the clean air compartment drives over the hose openings either continuously or controlled by pressure. In the direction of movement the first filter hose row is neutralised, while the second row is flushed from the clean air side. The third row is likewise neutralised. This results in a draught delay, which is necessary in order to allow the dislodged dust to fall into the discharge. The dust is discharged by a tried-and-tested drag conveyor with a downstream cellular wheel sluice. The return air pipes are provided with fire protection flaps and switching devices for exhaust air operation. The filter housing has been tested for resistance to pressure surges. Standard safety devices include likewise tested explosion pressure relief devices, fire extinguishing systems, mechanical and thermal monitoring systems as well as pressure-surge-resistant and flameproof cellular wheel sluices. The transport fan is arranged on the clean air side and is not exposed to swarf and dust. Hence, the conditions of a dust explosion zone do not prevail in the transport fan. RSV/RXV filter This series essentially differs from the RS/RX series in that its fans are arranged on the clean air side. RSV/RXV filters are suitable only for vacuum pressure operation. The capacity range extends from approx. 20,000 - 300,000 m³/h. The filter hoses are likewise cleaned off using the material-preserving low-pressure purge-air system.

Serie LEVANTE WALL EXHAUST AXIAL FANS Wall-mounted exhaust fan with axial aspiration. Supplied with dowels for wall installation. Anti-static finish that provides protection from dust and dirt. The kit is available for installation on windows.

Based on the axial fan series MFB60B that has been extremely successful for many years on the market, SEPA EUROPE is now presenting a powerful upgrade with its PLB60B series. The fans of the PLB60B series, with the dimensions 60x60x15 mm have an optimized blade geometry that enables a maximum flow rate of 28 m³/h. The new SEPA fans set new standards in their class and are suitable for reliable CPU cooling in a broad range of applications. The robust ball bearing system guarantees a long service life of 70.000 h L10 and 550.000 h MTBF at 40 °C and ensures a safe and smooth operation over many years. The fail-safe axial fans are available in the operating voltages 5, 12 and 24. A PWM input with which the speed can be adjusted according to requirements is an available option.

Thanks to the intelligent combination of DC fans with a fully integrated AC/DC converter, AC fans can now be operated at speeds that are independent of the power frequency. Up to 4500 rpm can be realized and the flow rate significantly increased if required. The EC generation in the dimensions 80mm to 280mm and with several different speeds replaces the previous AC fans in situtations where there is no DC voltage available and requires less power in the process. The previous AC fans can be replaced without restriction as the EC fans have identical dimensions and thickness. The versions that are smaller than 180mm have a wide-range input and can be connected without problem, worldwide to all AC voltage networks without need for further adaptation. This is underlined by the UL approval of the entire fan series.

The fan and cooling specialist SEPA EUROPE has now added three further models to its slimline radial fan series. The latest additions impress with their compact dimensions of 38 x 40 x 5 mm, 54 x 52 x 6 mm and 45 x 45 x 4 mm and have more than deserved the name „slimline“. All fans are equipped with the reliable Magfix sleeve bearings and have a service life of 210 000 h (MTBF) and 40 000 h /L10) at 40 °C. The PWM input in combination with the tacho output enables the speed to be controlled and monitored. It is not obvious at first glance, but the Model HY45AB05PNK00A tops with a pressure of 143 Pa. The new models will be included in the standard range and will therefore be available shortly from stock. SEPA EUROPE specializes in customized cooling solutions. Thanks to over 25 years of experience, SEPA EUROPE can offer you the appropriate solution for virtually every task.

Serie LPE HELICAL FANS FOR WALL The LPE serie’s fans, present constructive characteristics that allow both the utilization in the industrial applications and the installations in the tertiary environments (workshops, stores, breedings, glasshouses) where there is the real necessity of the employment of a fan with easy installation, low consumptions, and reduced noise pressure levels.

Replacement Fan Clutches for K22RA & Repair Kits for Kysor’s K22RA and K22FA The Klondike Series line allows you to benefit from Horton’s industry leading customer service and quality even if you are running our competitor’s fan drive in your fleet. The line includes a replacement fan clutch for Kysor’s K22RA; Major Kits, Seal Kits and Lining Kits for repairing Kysor rear- or front-air fan clutches; and five Hub Bearing Kits for Kysor's K22RA fan clutches. With Klondike Series products, you get guaranteed on-time delivery and the reliable industry-leading support you need to keep your fleet running smoothly. Benefits - Horton quality and reliability - Guaranteed on-time delivery - Reliable industry-leading support Features - Interchangeable with original equipment fan clutches and parts - Fan clutch replacement engages without air pressure to keep the engine cool until service is available Applications - Heavy-duty trucks - Medium-duty trucks - Buses Fan Clutch HORTON # 9908500; OEM # 1090-08500-01 Rear-Air Major Kit HORTON # 9908400; OEM # 1033-05435-03 Rear-Air Seal Kit HORTON # 9908402; OEM # 1033-08233-01 Front-Air Major Kit HORTON # 9908401; OEM # 1033-05435-02 Front-Air Seal Kit HORTON # 9908404; OEM # 4043-41130-01 Lining Kit (Fits both Rear-Air and Front-Air) HORTON # 9908403; OEM # 1033-08250-01 Hub Bearing Kits HORTON # 9908300; OEM # 1033-07781-01 HORTON # 9908301; OEM # 1033-07782-01 HORTON # 9908302; OEM # 1033-07782-02 HORTON # 9908303; OEM # 1033-07782-03 HORTON # 9908304; OEM # 1033-07782-04 Links - Order or View Literature

CAF45AC is a fan ideal for usage inside greenhouses and tunnels as it is highly efficient in air movement, silent and it resists greatly inside their moist and corrosive environment. It also offers operating safety, being equipped with a protective grill. A continuous air flow ensures better and healthier crops. The fans can be installed in series or in parallel. A personalized offer can be given if provided with the size of your greenhouse and the available hanging points. For more information check out our website or contact us.

*Made Of Galvanized Metal Plate *Wihtout Motor *Air System Easily With The Help Of Rectangular Fans *Designed For The Needs Of Middle Upper Aspiration Capacity *With The Help Of The Maintenance Covers, Engine And Fan Can Be Fixed Without Removing The Equipment.

Collecting dust Fume/gas elimination Handling fine grained material (marble dust, granule, plastique etc.) At printing houses, different factories such as textile,

Since the impellers are made of aluminium as areas of usage gas plants and acidic places preferred. Aspiration of smoke, iron foundry, cement plants, and paper mills Aspiration of moist and dusty air Industrial buildings, animal farms, greenhouses, garages, sport centers, and parks etc.