Connection technology - Import export

Specially developed flexible grids in combination with electroconductive coatings provide high tensile strength and outstanding electro conductive properties solidian eGRID is now also available with different conductive surface treatments for special applications in which electrical conductivity is important. What is the problem? While raw carbon fibers themselves have very good electrical conductivity textile reinforcements are usually impregnated with a polymer that insulates the grid. Depending on the product and the impregnation polymer the surface of the carbon fibers is more or less covered and can not be electrically connected. The new technology allows us to generate a fully conductive surface of the reinforcement and to connect all carbon filaments to one conductive unit.

Universal fastening element. The hammer-headed screw is twisted into the profile slot and so can mounted into an existing systems at a later date. The serrations break through the anodised film and creates a secure, electrical conductive connection.

The slot nut is twisted into the profile slot and so can be subsequently inserted into existing systems. The spring-loaded ball allows the nut to be fixated anywhere in the profile slot.

In the field there is a frequent need to measure sensor readings rapidly and easily right at the sensor and to transfer them directly to a PC without additional amplifiers or converters. The 9206 USB sensor interface can satisfy this requirement admirably, thanks to its „plug & measure“ design. The USB connection means installation could not be simpler. Typical applications: —Mobile test measurements via laptop —Laboratory test set-ups —Instrumentation and control —Diagnostic measurements in the chemical industry —PC-based recording of expansion figures in bio engineering The USB sensor interface takes its supply from the connected PC via the USB port, and uses it to generate the power supply for the sensors. The initial settings and sensor settings are made by burster in-house and saved in the USB sensor interface. These can then be fine-tuned by the customer.

Our universal construction kit with a variety of connections combines the latest technology with the best userfriendliness. Triclamp, milk pipe thread, inside thread and various customer versions as well as FDA / ATEX certification meet all requirements. screw connection G 3/4” – G 2” DN10 – DN50

The Puro® weight indicator is suitable for a wide variety of industrial weighing tasks. A large, bright display, a traffic light function and five tactile keys ensure convenient operation of the powerful applications. User-friendliness is combined with simple charging and connection technology. The rechargeable lithium-ion battery is easy to change and provides operating time for up to 500 hours. — Large display and a traffic light function for easy and comfortable weighing — Instant stabilisation — Highly developed battery with exceptional operating time — Easy charging via USB-C

ALPHA SHOWCASES - the new display generation Reflection on the essential ☑ Fully demountable ☑ optimal use of materials and components ☑ laminated glass and the patented FRANK connection system ☑ available in three sizes The innovative design is based on the patented FRANK connection technology. This makes gluing and screwing superfluous. The essential detail is the barely noticeable aluminium profile strips, which are precisely inserted into the patented edge profiling of the panes. Sealing materials, such as silicone etc. are not necessary. This facilitates assembly and ensures a long life without maintenance. The freestanding ALPHA showcase, step-in model from Frank, has won in its minimalist design international awards and convinced many directors/curators with its maximum transparency. The discreet lines express the lightness of the construction. Function and design are perfectly balanced in all simplicity. This simplicity is the highest form of perfection.

The 9206 USB sensor interface series is ideally suited to Notebook-based mobile use for high-precision, traceable calibration jobs that must be performed on-site for equipment such as presses, torque measurement facilities and pressure control systems. A factory calibration certificate or German-accredited DAkkS calibration certificate can optionally be provided for the USB interface plus relevant sensors, ensuring compliance even with the stringent traceability requirements of quality assurance standards. Specific characteristics: —Cost effective "Plug&Measure" concept —24-bit resolution —Practical and convenient DigiCal calibration and data acquisition software —Pt100 as option —Free LabView driver DLL for integrating in your own software environment —Multipurpose reference measurement chain with optional factory calibration certificate or Germanaccredited DAkkS calibration certificate —6-wire connection technology

User-friendly and intuitive Economical owing to highest availability Robust and extremely low maintenance Powerful Variable strap width 60 cycles per minute, with High-Speed Kit (optional) ASLF 'Anti-Strap-Loss-Function' Constant strap control Automatic cycle start by tabletop sensor (optional) Automatic Strap feed Strap width 5 - 12 mm, either Strap end detection system with automatic discharge of remaining strap Automatic strap tensioning (optional) Coil holder inside (either externally) Operation Terminal with Soft-Button DAT 'Direct-Access-Technology' The exclusive eject function avoids strap jam Torque controlled strap tension, adjustable Single-Copy-Strap Foot-bar at the operator side Machine movable MFT 'Mono-Frame-Technology' Power connection top (either bottom) Table height steplessly adjustable Table top front hinged by 270 °, removable Wear-free, energy saving direct-drive-motors Low maintenance and low wear strap arch Many specific options available, easily configurable

User-friendly and intuitive Economical owing to highest availability Robust and extremely low maintenance Variable strap width ASLF 'Anti-Strap-Loss-Function' Constant strap control Automatic cycle start by tabletop sensor (optional) Automatic Strap feed Strap width 9 or 12 mm Strap end detection system with automatic discharge of remaining strap Automatic strap tensioning (optional) Coil outside Operation Terminal with Soft-Button DAT 'Direct-Access-Technology' The exclusive eject function avoids strap jam Torque controlled strap tension, adjustable Machine movable MFT 'Mono-Frame-Technology' Power connection top (either bottom) Table height steplessly adjustable Table top front hinged by 270 °, removable Wear-free, energy saving direct-drive-motors Low maintenance and low wear strap arch Many specific options available, easily configurable

User-friendly and intuitive Economical owing to highest availability Robust and extremely low maintenance Variable strap width Stainless steel configuration 60 cycles per minute, with High-Speed Kit (optional) ASLF 'Anti-Strap-Loss-Function' Constant strap control Automatic cycle start by tabletop sensor (optional) Automatic Strap feed Strap width 5 - 12 mm, either Strap end detection system with automatic discharge of remaining strap Automatic strap tensioning (optional) Coil holder inside (either externally) Operation Terminal with Soft-Button DAT 'Direct-Access-Technology' The exclusive eject function avoids strap jam Torque controlled strap tension, adjustable Single-Copy-Strap Foot-bar at the operator side Machine movable MFT 'Mono-Frame-Technology' Power connection top (either bottom) Table height steplessly adjustable Table top front hinged by 270 °, removable Wear-free, energy saving direct-drive-motors Low maintenance and low wear strap arch Many specific options...

User-friendly and intuitive Economical owing to highest availability Robust and extremely low maintenance Powerful Variable strap width 60 cycles per minute, with High-Speed Kit (optional) ASLF 'Anti-Strap-Loss-Function' Constant strap control Automatic cycle start by tabletop sensor (optional) Automatic Strap feed Strap width 5 - 12 mm, either Strap end detection system with automatic discharge of remaining strap Automatic strap tensioning (optional) Coil holder inside (either externally) Operation Terminal with Soft-Button DAT 'Direct-Access-Technology' The exclusive eject function avoids strap jam Torque controlled strap tension, adjustable Single-Copy-Strap Foot-bar at the operator side Machine movable MFT 'Mono-Frame-Technology' Power connection top (either bottom) Table height steplessly adjustable Table top front hinged by 270 °, removable Wear-free, energy saving direct-drive-motors Low maintenance and low wear strap arch Many specific options available, easily configurable

With the MiJET part cleaning system it is possible to keep workplaces clean and workpieces hygienically cleaned with the simplest technology. An electrical connection is not necessary. Only a compressed air connection is required to use the device. Application The actual task of the MiJET is to filter oily air. Chips of the work pieces accumulate in the container. Operators often tend to blow off finished workpieces into the machine. This quickly results in dirty working environments and poor air in the production hall. However, we avoid this by exhausting these fumes. Oils are trapped from the exhaust air and chips and coolants accumulate in the container.

With the MiJET part cleaning system it is possible to keep workplaces clean and workpieces hygienically cleaned with the simplest technology. An electrical connection is not necessary. Only a compressed air connection is required to use the device. Application The actual task of the MiJET is to filter oily air. Chips of the work pieces accumulate in the container. Operators often tend to blow off finished workpieces into the machine. This quickly results in dirty working environments and poor air in the production hall. However, we avoid this by exhausting these fumes. Oils are trapped from the exhaust air and chips and coolants accumulate in the container.

Our universal construction kit with a variety of connections combines the latest technology with the best userfriendliness. Triclamp, milk pipe thread, inside thread and various customer versions as well as FDA / ATEX certification meet all requirements. TriClamp ½", ¾", 1”, 1¼", 1½", 2" DN15, DN20, DN25, DN32, DN40, DN50

Alarm messages can be signalled optically and acoustically at the pumping station or transmitted remotely by mobile phone or phone line. Optical and acoustic alarm in 12 V DC technology for connection to the alarm unit AG 230/12. Product features Multi-tone series combined with xenon flash 32 different tones can be set Volume adjustable up to 105 dB Optical and acoustic signals can be triggered separately

Rectifier and Battery Charger that can be connected in parallel Multi-master Parallel Connection Technology Adjustable Output Voltage between 0V-1000VDC Parallel connection up to 16 units High power solution up to 10 MVA Equal Load Sharing Input Isolation Transformer Durable structure with thyristor technology Production at all industrial input voltages Ni-cd, Lead Acid and Stationary battery charging DC Earth Leakage protection Low Voltage / High Voltage protection Overload protection Over temperature protection Efficiency >% 95 7” Touchscreen Operator Panel Suitable design for industrial environment TS EN ISO 9001: 2015 Quality Certified

Comprehensive monitoring and alarm functions enable you to react quickly as needed to ensure the reliable availability of heating energy and process heat. — Convenient remote monitoring of your boiler system and access to all important operating parameters — Simply integrate the remote technology for connection via Internet or a company network — Fast and cost-efficient online support from Bosch experts on request — Safety first: Certified, multilevel security concept for your remote access — Automatic alarm notification by text message or e-mail as an option so you can react quickly when needed

Two independent firing units and flue gas paths create a double control range for individual heat consumption. — Very high efficiency across all power ranges — Particularly suitable for highly fluctuating heat and process heat demand — Reliable solutions for heating plants and the manufacturing industry with temperature levels up to 225 °C — Heat supply for the future: Low-NOx or CO2-neutral operation possible — Complete system with intelligent control technology and protected remote connection — Proven and durable boiler technology Made in Germany — Fuel: Oil, gas, multi-fuel firing, Biogas, bio-oil, hydrogen, special fuels

The eurolaser laser cutting machine M-1200 for acrylic glass is a compact model with a processing area of 1,330 mm x 1,230 mm (52.3" x 48.4"). Just like all eurolaser laser cutting machines the sealed-off laser technology in connection with exchangeable modular assembly groups reduces the lifecycle costs to a minimum. An investment which pays off! The requirement-focused modular design enables eurolaser laser systems to be specially configured to suit every requirement and at the same time provides the necessary flexibility. The system design is focused mainly on requirements that are generated from later use.

The eurolaser laser cutting machine M-1200 for foils and membrane switches is a compact model with a processing area of 1,230 x 1,330 mm (48.4" x 52.3"). Just like all eurolaser laser cutting machines the sealed-off laser technology in connection with exchangeable modular assembly groups reduces the lifecycle costs to a minimum. An investment which pays off!

The eurolaser laser cutting machine M-1200 for textiles is a compact model with a processing area of 1,230 x 1,330 mm (48.4" x 52.3"). Just like all eurolaser laser cutting machines the sealed-off laser technology in connection with exchangeable modular assembly groups reduces the lifecycle costs to a minimum. An investment which pays off!

The eurolaser laser cutting machine M-1200 is a compact model with a processing area of 1,330 x 1,230 mm (52.3" x 48.4"). Just like all eurolaser laser cutting machines the sealed-off laser technology in connection with exchangeable modular assembly groups reduces the lifecycle costs to a minimum. An investment which pays off! The modular design enables eurolaser systems to be specially configured to suit every requirement. We analyze your requirements and configure the laser system individually for you. The usage of eurolaser laser machines enables you to process a wide range of materials, such as cutting of plastics, foams, textiles, adhesive foils, wood, acrylic, composite materials and much more. We are pleased to run a cutting test in our Application Center by using your individual material. Subsequently, you will receive a detailed test report in order to identify how your material was cut and engraved with our laser machines.

The eurolaser laser cutting machine M-1200 for wood is a compact model with a processing area of 1,330 mm x 1,230 mm (52.3" x 48.4"). Just like all eurolaser laser cutting machines the sealed-off laser technology in connection with exchangeable modular assembly groups reduces the lifecycle costs to a minimum. An investment which pays off!

The Classic Line includes DC spring-pressure single-disc and multi-disc brakes which, due to their robust design and the variable connection technology, meet the requirements of demanding applications. Electromagnetically-operated spring-applied brakes build up the braking torque when the current is switched off and the electromagnetic force is therefore neutralized.

Whenever pre-assembled cables need to be led into a housing, the cable entry system KADL is the perfect solution. KADL is installed with one click - easy and timesaving. The modular structure allows a step-by-step installation of 3 to 25 cables. With 16 different grommets a wide clamping range from 3 to 32,5 mm can be covered. - For applications where you need to insert and seal pre-assembled cables with connectors into housings - Tool-free entry and connecting technology for machines and equipment - Temperature range -30 °C to +100 °C - Protection grade IP65 - UL 514B - 12 different frame combinations with 16 sizes of grommets (accessory) - Click-in assembly at wall thickness from 1,5 - 2,0mm - For walls with thickness larger 2,0 mm the KADL can be fixed with standard screws

Various requirements are imposed on modern device connection technology today. The main issues are progress in miniaturisation in engine and machine design as well as applications with increased power requirements. Safe data transmission must always be guaranteed, even in harsh environmental conditions. For connection on the device side, CONEC offers a broad range of unit side connectors. Fields of application are, amongst others: distribution cabinets, engine and speed sensor connection technology

Various requirements are imposed on modern device connection technology today. The main issues are progress in miniaturisation in engine and machine design as well as applications with increased power requirements. Safe data transmission must always be guaranteed, even in harsh environmental conditions. For connection on the device side, CONEC offers a broad range of unit side connectors. Fields of application are, amongst others: distribution cabinets, engine and speed sensor connection technology

Various requirements are imposed on modern device connection technology today. The main issues are progress in miniaturisation in engine and machine design as well as applications with increased power requirements. Safe data transmission must always be guaranteed, even in harsh environmental conditions. For connection on the device side, CONEC offers a broad range of unit side connectors. Fields of application are, amongst others: distribution cabinets, engine and speed sensor connection technology