Shorts - Import export

Thread standard: Metric, ISO DIN 13 Type: Round die Application: For brass Material of product: HSS Spiral entry: yes For materials: Brass (short and long chipping) Tensile strength up to: Standard: DIN 223 Tolerance: ISO-6g Special geometry for brass. Lapped for sharp cutting edges, smooth surface and increased tool life time. Round dies are cylindrical and are used for making external threads in one operation. They have - depending on the size - three or more cutting edges inside. The holes between the cutting edges receive the chips, roll them and discharge them. Dies are used to cut screws, nuts and threaded rods in everyday use. The die holder is used to cut the threads by hand and with the special die holders you can also attach the round die to a tailstock or to a drill. The dies can usually be used on both sides and have a perfect cut. Our taps and dies are produced to the highest quality standards, to ensure precise quality threads.

Thread standard: Metric Fine, ISO DIN 13 Type: Short machine tap Form D, for through and blind holes Application: General use Material of product: HSSG Surface treatment: no For materials: Unalloyed and low alloyed steel, non abrasive material Tensile strength up to: 800 N/mm2 Standard: DIN 2181 Tolerance: ISO2/6H Efficient internal thread cutting. The short structural type makes this tap usable by machine and hand. Our taps and dies are produced to the highest quality standards, to ensure precise quality threads. Wide range of hand, machine and rolling taps, dies and tools for cutting professional threads on various materials Correct lubrication is important for successful thread cutting and to decrease the wear of taps and dies. We recommend using our lubricants. Brand: Baer Tools (Germany)

Thread standard: Metric, ISO DIN 13 Type: Short machine tap Form D, for through and blind holes Application: General use Material of product: HSSG Surface treatment: no For materials: Unalloyed and low alloyed steel, non abrasive material Tensile strength up to: 800 N/mm2 Standard: DIN 352 Tolerance: ISO2/6H Efficient internal thread cutting. The short structural type makes this tap usable by machine and hand. Our taps and dies are produced to the highest quality standards, to ensure precise quality threads. Wide range of hand, machine and rolling taps, dies and tools for cutting professional threads on various materials

The S19, S20 (Short version) are inserts for plastic with heat/ultrasonic installation into cylindrical holes In the short version these inserts offer the advantage of having reduced dimensions, shorter installation times and lower costs. On the other hand, the resistance to torque and pull out loads is reduced comparing to long version Suitable for all types of thermoplastics, even dry and fragile ones such as polycarbonates The S19, S20 inserts are designed with a wide center knurl coupled with two smaller knurls and deep undercuts on both ends to maximize torque and pull out performance They induce very low radial stresses and are therefore particularly recommended in holes with thin walls. In this case the hole must be a bit wider. Optimal size should be determined after appropriate practical tests Installation must be carried out using heat conduction or ultrasonic machines. The holes should be sized as indicated in the product datasheet

The S14 (Short version) are inserts for plastic with heat/ultrasonic installation into tapered holes with an 8° angle In the short version these inserts offer the advantage of having reduced dimensions, shorter installation times and lower costs. On the other hand, the resistance to torque and pull out loads is reduced comparing to long version Suitable for all types of thermoplastics, even dry and fragile ones such as polycarbonates The tapered form facilitates proper seating and maximizes the surface contact between the insert and hole wall prior to the application of heat or ultrasonic vibration. These inserts are the best choice when using ultrasonic insertion techniques The insert's straight-toothed upper ring and oblique-toothed middle ring provide high torque and pull out resistance, ensuring complete filling of the plastic material in the cavities below Installation must be carried out using heat conduction or ultrasonic machines.

The S29, S30 (Short version) are inserts for plastic with heat/ultrasonic installation into cylindrical holes In the short version these inserts offer the advantage of having reduced dimensions, shorter installation times and lower costs. On the other hand, the resistance to torque and pull out loads is reduced comparing to long version Suitable for all types of thermoplastics, even dry and fragile ones such as polycarbonates These inserts were designed to provide faster speed and ease of installation, and at the same time maximize torque and pull out performance. The outer profile was made symmetrical with respect to length, so that the insert does not have to be oriented during the installation process. These inserts are therefore suitable for automatic type installations in large volume The S29, S30 offer much higher torque and pull-out resistance than all other inserts Holes sizes are identical to those of the S19 and S20 inserts to provide an easy alternative