Long holes - Import export

High quality self-tapping ensat thread inserts. Made of ASIS 304 stainless steel Long version with three cutting holes, Ensat 308 standard Particularly designed for materials resistant to cutting and where you want to exclude any slight self-locking effect on the screw. With the same insertion torque, they exert a higher and better distributed cutting force compared to Ensat 302 inserts, having three cutting points instead of two. Similar to Ensat 307 but longer, so can be applied in thicker materials These inserts are self-tapping and do not require pre-threading. They can be easily installed by screwing them into the appropriately sized hole using the installation tool They are usually used to enforce or repair threads in metallic materials with low shear resistance (metal alloys, aluminum, cast iron, plastic, castings, etc.). These self-threading bushes have an internal thread for the screw and an external thread with cutting slots to insert itself into the material

The S14 (Long version) are inserts for plastic with heat/ultrasonic installation into tapered holes with an 8° angle These are the longer versions of the S14 Short inserts for higher torque and pull-out resistance Suitable for all types of thermoplastics, even dry and fragile ones such as polycarbonates The tapered form facilitates proper seating and maximizes the surface contact between the insert and hole wall prior to the application of heat or ultrasonic vibration. These inserts are the best choice when using ultrasonic insertion techniques The insert's straight-toothed upper ring and oblique-toothed middle ring provide high torque and pull out resistance, ensuring complete filling of the plastic material in the cavities below Installation must be carried out using heat conduction or ultrasonic machines. The holes should be sized as indicated in the product datasheet Inch version from 2-56 to 5/16-18 is available upon request

The S19, S20 (Long version) are inserts for plastic with heat/ultrasonic installation into cylindrical holes These are the longer versions of the S19, S20 Short inserts for higher torque and pull-out resistance Suitable for all types of thermoplastics, even dry and fragile ones such as polycarbonates The S19, S20 inserts are designed with a wide center knurl coupled with two smaller knurls and deep undercuts on both ends to maximize torque and pull out performance They induce very low radial stresses and are therefore particularly recommended in holes with thin walls. In this case the hole must be a bit wider. Optimal size should be determined after appropriate practical tests Installation must be carried out using heat conduction or ultrasonic machines. The holes should be sized as indicated in the product datasheet

High quality zinc plated steel self-tapping ensat thread inserts. Made of galvanized steel, conforming to RoHS, this ensures excellent wear and corrosion resistance Long version with three cutting holes, Ensat 308 standard Particularly designed for materials resistant to cutting and where you want to exclude any slight self-locking effect on the screw. With the same insertion torque, they exert a higher and better distributed cutting force compared to Ensat 302 inserts, having three cutting points instead of two. Similar to Ensat 307 but longer, so can be applied in thicker materials These inserts are self-tapping and do not require pre-threading. They can be easily installed by screwing them into the appropriately sized hole using the installation tool They are usually used to enforce or repair threads in metallic materials with low shear resistance (metal alloys, aluminum, cast iron, plastic, castings, etc.).

Thread standard: Metric, ISO DIN 13 Type: Machine nut tap Application: General use Material of product: HSSE Surface treatment: no For materials: Unalloyed and low alloyed steel, non abrasive material Tensile strength up to: 850 N/mm2 Standard: DIN 357 Tolerance: ISO2/6H Maschine Nut tap for through holes with long shank for taking some thread cutted nuts. For thread depth up to 1,0 times diameter. Also useable for thread cutting in awkward places. Our taps and dies are produced to the highest quality standards, to ensure precise quality threads. Wide range of hand, machine and rolling taps, dies and tools for cutting professional threads on various materials Correct lubrication is important for successful thread cutting and to decrease the wear of taps and dies. We recommend using our lubricants.

Thread standard: Metric, ISO DIN 13 Type: Machine tap Form B with spiral entry, for through holes Application: Overlengthed (long shank) L=150 Material of product: HSSE Surface treatment: no For materials: Unalloyed and low alloyed steel, non abrasive material Tensile strength up to: 900 N/mm2 Standard: DIN 371/376 Tolerance: ISO2/6H Tap for machine use and through holes. The spiral point pushes the chips ahead and prevents clogging of the flutes. Overlengthed (long shank), L=150 Our taps and dies are produced to the highest quality standards, to ensure precise quality threads. Wide range of hand, machine and rolling taps, dies and tools for cutting professional threads on various materials Correct lubrication is important for successful thread cutting and to decrease the wear of taps and dies. We recommend using our lubricants

Thread standard: Metric, ISO DIN 13 Type: Machine tap Form B with spiral entry, for through holes Application: Overlengthed (long shank) L=100 Material of product: HSSE Surface treatment: no For materials: Unalloyed and low alloyed steel, non abrasive material Tensile strength up to: 900 N/mm2 Standard: DIN 371/376 Tolerance: ISO2/6H Tap for machine use and through holes. The spiral point pushes the chips ahead and prevents clogging of the flutes. Overlengthed (long shank), L=100 Our taps and dies are produced to the highest quality standards, to ensure precise quality threads. Wide range of hand, machine and rolling taps, dies and tools for cutting professional threads on various materials Correct lubrication is important for successful thread cutting and to decrease the wear of taps and dies. We recommend using our lubricants.