High-temperature pump - Import export

Modern petrochemical and gas industries typically use horizontal centrifugal canned pump units with magnetic couplings similar to Villina-GNGC type pumps. They are designed for transiting neutral, corrosive, toxic, as well as explosive and flammable liquids in stationary conditions, the vapors of which can form explosive mixtures with air. Magnetic coupling pumps combine complete tightness, smooth operation, long service life and high maintainability. A sub-type of horizontal pumping units are high-temperature pumps Temperature of the pumped fluid: -50°C to +420°C; viscosity up to 26 cSt; density 2,000 kg/m3 maximum; mass concentration of solid non-abrasive inclusions up to 0.2%; size 0.2 mm maximum Permanent magnets (SmCo) with an operating temperature of up to 450°C are used for operation in these temperature conditions. The pump, a part of the pumping unit, is a single-stage or multi-stage horizontal centrifugal section-type

Planar ceramic heater oxygen sensors are subject to extreme conditions. A properly functioning oxygen sensor forms the basis for reliable engine operation and thus fuel economy, low pollutant emissions, and good exhaust gas values. Oxygen sensors with planar ceramic heater characteristics: ● Quick ignition time ● Good insulation performance ● Strong resistance to high temperature and poisoning ● Long lifetime ● Pump current switch type, conventional switch type, air-fuel ration type, and wide range type are available Appliaction: Plate Ceramic Heater Chip for Automobile / Oxygen Sensor

Planar ceramic heater oxygen sensors are subject to extreme conditions. A properly functioning oxygen sensor forms the basis for reliable engine operation and thus fuel economy, low pollutant emissions, and good exhaust gas values. Oxygen sensors with planar ceramic heater characteristics: ● Quick ignition time ● Good insulation performance ● Strong resistance to high temperature and poisoning ● Long lifetime ● Pump current switch type, conventional switch type, air-fuel ration type, and wide range type are available Appliaction: Plate Ceramic Heater for Automobile / Oxygen Sensor

Planar ceramic heater oxygen sensors are subject to extreme conditions. A properly functioning oxygen sensor forms the basis for reliable engine operation and thus fuel economy, low pollutant emissions, and good exhaust gas values. Oxygen sensors with planar ceramic heater characteristics: ● Quick ignition time ● Good insulation performance ● Strong resistance to high temperature and poisoning ● Long lifetime ● Pump current switch type, conventional switch type, air-fuel ration type, and wide range type are available Appliaction: Plate Ceramic Heater for Automobile / Oxygen Senser

One-plunger pumping units PT 1.1 with capacity up to 8 m3/h and pressure up to 40 MPa Three-plunger pump units according to API 674 (3-d edition) PT 1.3 and PT 2.3 with a capacity of 0.2 m3/h to 60 m3/h and pressure up to 80 MPa Five-plunger pumping units Pumping units are designed for pumping various liquids, including chemically active ones, with temperatures from -15 ° С to + 450 ° С, kinematic viscosity of not more than 8 cm / s, with the content of solid non-abrasive particles up to 0.2% by weight and size up to 0.2 mm.

Expanded natural Graphite in Purity 98 % – industrial grade or 99.85 % nuclear grade (chlorine content < 20 ppm) Temperature in steam Density min. 1.40 g/cm 3 Characteristics High cross section density Self lubrication and limited wear Dry running capability Coefficient of thermal expansion similar to steel Maintenance free and elastic, also under variable pressure Non ageing, high chemical resistance Attention! Precise tolerances and surfaces of application are requeste Operating range Pressure [p max]: 800 bar Temperature: t = -200… +550 °C pH: 0 - 14 Density: 1.80 g/cm³ Temperature in steam Density min. 1.40 g/cm 3 Main application Fittings Pumps (high temperature) Covers Valves Suitable for Valves and fittings of all Industries Approvals Oxygen BAM 200 °C/250 bar DVGW and KTW Variant Rings with integrated reinforcement or endcaps made from ANSI 316 Special quality TA Luft 300 with a leakage rate of 5.7 · 10 -3 mbar · l/(s·m) 300 °C Form of delivery ARF rings - endless,...

Introducing the MVHHT Series: High-temperature filters built to withstand the heat. Crafted with micro glass fiber media and separator, available in stainless steel or galvanized steel frames. Resilient up to 250 degrees, these filters are essential for air conditioning systems and industrial processes. "

High-Pressure Cleaning, Load Change Systems and Pressure Test Systems If your application requires forced lubrication and an oil cooler may be required, the powerful K9000-3G three-plunger high-pressure pump is an alternative to the smaller K8000-3G three-plunger high-pressure pump. Like the compact K8000 model, this 90 kW high-pressure pump is suitable for smaller industrial applications such as industrial cleaning, jetting or process engineering. SPECIAL FEATURES - Capacities at 100% volumetric efficiency and 20°C ambient temperature - Minimum inlet pressures depending on fluid - Speed range 10-100% depending on rod force - Forced lubrication gearbox (> 75 kW with oil cooler) - Standard gear ratios i = 2.75 - 3.22 - 3.68 - Also available to API 674 - Special fluids such as seawater, glycol, methanol, oils, etc. on request - Vertical operation possible

Our High Temperature Tapes are perfect for all kinds of masking uses during processes which regularly use a lot of heat, examples of these processes includes Powder Coating where powder is sprayed on as a coating before being baked on to an application for a permanent finish. Coming in a huge number of variations including Ultra high temperature & Low tack adhesives, you can rest assured that we have the best choice for you. As mainly film based products, these High Temperature Tapes are malleable and flexible meaning that they can be used for tricky areas where there are many sharp corners.Discs are also available which can be used to seal off and prevent small holes such as screw holes from becoming filled during the coating process. For our full selection of Powder Coating Tapes / High Temperature Tapes please visit our website using the link below. Free sample lengths are available on all our tapes meaning you can try before you buy.

Melt pump for building up pressure in the polymer process. The series is the result of a complete revision of the core components used. The BOOSTER-AT is available with flange connections according to EN1092-1 and ANSI B16.5. Thanks to the new gear wheel geometries, differential pressures of up to 320 bar are possible with selected pump sizes. The new design is rounded off by the usual variety of different material combinations. Advantages: Higher efficiency, therefore Less temperature input into the polymer Wider viscosity range possible Larger volume flow range possible Increased safety against shaft breakage in case of overload due to new design

The reliable booster pump for the polymer process. BOOSTER gear pumps from WITTE are used in the polymerisation process to increase the pressure of medium to high viscosity media. The hydraulically heated booster pump conveys very gently prepolymers and polymers, such as PET, PBT, PS, ABS and many others. Heating is by means of heat transfer oil or steam. The core components such as shafts and slide bearings come from the WITTE modular system. The booster pumps of the BOOSTER series are used wherever particularly high pressure is required for the process. High pressures are required for pelletising, fibre production or for spinning pumps, among others. The design of the BOOSTER booster pumps can be adapted to the needs of the plant and the customer's requirements.

High-temperature vacuum-formed products made from biosoluble ceramic fibres are lightweight and solid parts or structural elements that can be used at temperatures up to 1.400 °C in air and in aggressive environments, including direct contact with liquid metals. — 100% biosoluble — high temperature resistance — low thermal conductivity — high chemical resistance * — low weight — good tear resistance — high flexibility — easy processing — complicated geometries can be produced — recyclable * to achieve higher acid resistance, a special coating is required. Available from manufacturer. Application: Burner plant components, crucibles, thermocouple housings, coupling devices in continuous casting plants, channel elements of metal troughs, inlet device in the melting of non-ferrous and ferrous metals, gasket in aluminium foundries, gaskets in blast furnaces, expansion joints, pipe insulation, catalyst insulation, repair work in the high temperature range.

High-temperature vacuum-formed products made from biosoluble ceramic fibres are lightweight and strong parts or structural elements that can be used at temperatures up to 1 .600 °C in air and in aggressive environments, including direct contact with liquid metals. — 100% natural — biosoluble — high thermal shock resistance — low thermal conductivity — high chemical resistance * — recyclable — low weight — good tear resistance — high flexibility — easy processing — harmless to health — complicated geometries can be produced * A special coating is required to achieve high acid resistance. Available from manufacturer. Fields of application: gaskets, crucibles, thermocouple housings, coupling devices in continuous casting plants, expansion joints, convex and flat gaskets in blast furnaces, channel elements of metal troughs, inlet device in the melting of non-ferrous and ferrous metals.

Double filtration system is used in our high pressure coolant sytems. They are easily removable and cleanable. On the other hand, especially the main feature of this system is not to be obligated to stop machine during cleaning and changing filter. One filter can be operated with machine while another is been cleaning. This will provide you the time saving during filter change Multiple Manifold Block with 4 outlets is provided as standart in this model. However, it can be manufactured over 4 outlets depending on your requirements at your machining process. HP2 High Pressure Coolant Units are used as mobile station. They have wheels under units and you may easily move it where you prefer them to be placed at your workshop.