Pumps for solids - Import export

Depending on the pump housing, the diaphragm pumps operated by compressed air can be offered in metal or plastic. Air operated diaphragm pumps made of plastic The double diaphragm pumps made of plastic have a pump housing made of polyethylene or PTFE, each also in a conductive version as an ATEX pump for use in hazardous areas. The compressed air diaphragm pumps in solid construction made of polyethylene can be used for abrasive, viscous and shear sensitive media. Air operated diaphragm pumps made of metal The metal pumps have a pump housing made of aluminum, cast iron or stainless steel. All pumps are available with composite membranes made of PTFE, EPDM or NBR. The material of the valves and seals is coordinated according to the choice of membrane.

For liquids that have to be mixed before processing and then pumped or contain small solids, the new Diaphragm pumps with an integrated air-operated Double diaphragm pump is the perfect solution. The mixing and pumping process takes place via a suction and mixing tube and a 3-way valve. The pre-assembled system is immediately ready for operation with a few simple steps and is also suitable for explosive liquids. * Mixing and pumping integrated in one system * stufenlose Regelung der Folgeplatte über Steuerventil * Media examples: Paints and varnishes, emulsions, dispersions, suspensions, water/oil mixtures, liquids with increased viscosity and solids content Features & Advantages * Quick installation and time saving through easy handling * Compact design * Base plate offers good stability on the container lid * Easy to insert into the 2" bunghole of the container by balancer or overhead crane * No further mixer necessary

ProfiSampler PP for general samples, for weak acids, alkalis, detergents, chemical baths. Made of solid, chemical resistant Polypopylene. ProfiSampler PP, consisting of: Vacuum pump, made of solid PP, with feet, venting valve and bottle thread GL 40, 1 PP bottle 250 ml, 10 m PE suction hose (roll), 1 hose cutter, 1 stainless steel hose weight made of AISI 304 (1.4301), 20 seal-it bottle seals. While the MiniSampler is designed for laboratory use, the ProfiSampler has been specially developed for rough industrial use.

The ARP (Abrasive Resistant Pump) series was developed specially for the conveyance of water contaminated with grainy or fibrous solids. The ARP highpressure pumps deliver operating pressures up to 400 bar. The pumps also work reliably at a solids concentration of up to 3,000 mg/l and a grain size of up to 300 μm.

Our hero made of stainless steel for self-pumped waterNone of our high-quality submerged waste water pumps of the TWP series transports more water per hour. With its resistant pump housing, the submerged pump TWP 11000 ES made of stainless steel withstands even the most extreme weather conditions. The solid submerged pump guarantees an above-average and at the same time maintenance-free service life for water withdrawal from ponds, garden wells, cisterns or rain barrels as well as for pumping out and recirculating water in swimming pools and whirlpools, flooded basements, garages and building/drainage pits. This high degree of versatility makes the TWP 11000 ES an indispensable universal helper for passionate hobby gardeners, facility managers, homeowners or craftsmen.

The CryLaS High-Power series lasers are diode-pumped solid-state lasers (DPSS lasers) based on a microchip design. It consists of a Nd:YAG resonator with a directly coupled saturable absorber that works as a passive Q-switch. As the historically first development of CryLaS GmbH, the lasers are widely used in industrial and scientific application. They impress with their reliability, especially in the OEM business, and offer high pulse power with comparatively small housing dimensions. Thanks to frequency conversion, the lasers are available from IR to DUV. The FTSS355-300 laser delivers 300 µJ pulse energy at a maximum repetition rate of 20 Hz and a pulse width of 1.7 ns, i.e. a peak pulse power of 175 kW. CryLaS lasers impress with their simple installation, service-free operation and long laser lifetime. They are the ideal tool for OEM applications and demanding scientific lab use.

The CryLaS High-Power series lasers are diode-pumped solid-state lasers (DPSS lasers) based on a microchip design. It consists of a Nd:YAG resonator with a directly coupled saturable absorber that works as a passive Q-switch. As the historically first development of CryLaS GmbH, the lasers are widely used in industrial and scientific application. They impress with their reliability, especially in the OEM business, and offer high pulse power with comparatively small housing dimensions. Thanks to frequency conversion, the lasers are available from IR to DUV. The FDSS532-1000 laser delivers 1 mJ pulse energy at a repetition rate of 20 Hz and a pulse width of 1.8 ns, i.e. a peak pulse power of 550 kW. CryLaS lasers impress with their simple installation, service-free operation and long laser lifetime. They are the ideal tool for OEM applications and demanding scientific lab use.

The CryLaS High-Power series lasers are diode-pumped solid-state lasers (DPSS lasers) based on a microchip design. It consists of a Nd:YAG resonator with a directly coupled saturable absorber that works as a passive Q-switch. As the historically first development of CryLaS GmbH, the lasers are widely used in industrial and scientific application. They impress with their reliability, especially in the OEM business, and offer high pulse power with comparatively small housing dimensions. Thanks to frequency conversion, the lasers are available from IR to DUV. The FDSS532-150 laser delivers 150 µJ pulse energy at a maximum repetition rate of 100 Hz and a pulse width of 1.2 ns, i.e. a peak pulse power of 125 kW. CryLaS lasers impress with their simple installation, service-free operation and long laser lifetime. They are the ideal tool for OEM applications and demanding scientific lab use.

The CryLaS Q series lasers are diode-pumped solid-state lasers (DPSS lasers) based on a microchip design. This consists of an Nd:YAG resonator with a directly coupled saturable absorber which works as a passive Q-switch. The compact housing and easy operation make the lasers an optimum light source for applications that require minimal housing dimensions with highest performance. Based on the 1064 nm fundamental, harmonics are generated using non-linear (NLO) crystals that allow a wide spectrum of laser wavelengths from 1064 nm to 213 nm. The FQSS213-Q2 laser emits pulses with approximately 1 ns pulse width at 213 nm, and can be modulated from single shot to 10 kHz. The pulse energy is 0.1 µJ. CryLaS lasers impress with their easy installation, service-free operation and long service life. This makes them ideal for OEM applications and demanding laboratory setups.

The CryLaS Q-series lasers are diode-pumped solid-state lasers (DPSS lasers) based on a microchip design. It consists of a Nd:YAG resonator with a directly coupled saturable absorber that works as a passive Q-switch. The compact housing and simple operation make the lasers an ideal light source for applications that require minimal housing dimensions with maximum performance. Based on the 1064 nm fundamental, non-linear optics (NLO optics) generate frequency multiples of this fundamental, covering a broad spectrum of laser wavelengths from 1064 nm to 213 nm. The FDSS532-Q2 laser emits pulses with a pulse width of approx. 1 ns at 532 nm and can be modulated from single shot to 10 kHz. The pulse energy is 6 µJ. CryLaS lasers impress with their simple installation, service-free operation and long service life.

The CryLaS Q-series lasers are diode-pumped solid-state lasers (DPSS lasers) based on a microchip design. It consists of a Nd:YAG resonator with a directly coupled saturable absorber that works as a passive Q-switch. The compact housing and simple operation make the lasers an ideal light source for applications that require minimal housing dimensions with maximum performance. Based on the 1064 nm fundamental, non-linear optics (NLO optics) generate frequency multiples of this fundamental, covering a broad spectrum of laser wavelengths from 1064 nm to 213 nm. The FDSS532-Q3 laser emits pulses with a pulse width of approx. 1 ns at 532 nm and can be modulated from single shot to 2.5 kHz. The pulse energy is 20 µJ. CryLaS lasers impress with their simple installation, service-free operation and long service life.

The eMOPA product series is based on a diode-pumped, passively Q-switched solid-state laser as the master oscillator and a downstream diode-pumped power amplifier with a patented optical design. Wavelengths from the DUV to the green spectral range can be generated for this series: 213 nm, 266 nm, 355 nm and 532 nm. The eMOPA355-100 emits pulses with a pulse width of around 1 ns and 100 µJ pulse energy. The average output power is 100 mW in transverse single-mode operation at a wavelength of 355 nm and peak pulse powers of >80 kW. The repetition rate can be adjusted from single shot to a maximum of 1 kHz by external triggering or the supplied software. The eMOPA is ideal for 24/7 industrial use and is primarily used in ophthalmology. By adapting the lasers to the requirements of our customers, a wide range of applications is possible, such as photoacoustics and ophthalmological markings.

The CryLaS Q-series lasers are diode-pumped solid-state lasers (DPSS lasers) based on a microchip design. It consists of a Nd:YAG resonator with a directly coupled saturable absorber that works as a passive Q-switch. The compact housing and simple operation make the lasers an ideal light source for applications that require minimal housing dimensions with maximum performance. Based on the 1064 nm fundamental, non-linear optics (NLO optics) generate frequency multiples of this fundamental, covering a broad spectrum of laser wavelengths from 1064 nm to 213 nm. The FDSS532-Q4 laser emits pulses with a pulse width of approx. 1 ns at 532 nm and can be modulated from single shot to 1 kHz. The pulse energy is 42 µJ. CryLaS lasers impress with their simple installation, service-free operation and long service life.

The CryLaS Q series lasers are diode-pumped solid-state lasers (DPSS lasers) based on a microchip design. This consists of an Nd:YAG resonator with a directly coupled saturable absorber which works as a passive Q-switch. The compact housing and easy operation make the lasers an optimum light source for applications that require minimal housing dimensions with highest performance. Based on the 1064 nm fundamental, harmonics are generated using non-linear (NLO) crystals that allow a wide spectrum of laser wavelengths from 1064 nm to 213 nm. The FQSS213-Q1 laser emits pulses with approximately 1 ns pulse width at 213 nm, and can be modulated from single shot to 20 kHz. The pulse energy is 0.05 µJ. CryLaS lasers impress with their easy installation, service-free operation and long service life. This makes them ideal for OEM applications and demanding laboratory setups.

The CryLaS High-Power series lasers are diode-pumped solid-state lasers (DPSS lasers) based on a microchip design. It consists of a Nd:YAG resonator with a directly coupled saturable absorber that works as a passive Q-switch. As the historically first development of CryLaS GmbH, the lasers are widely used in industrial and scientific application. They impress with their reliability, especially in the OEM business, and offer high pulse power with comparatively small housing dimensions. Thanks to frequency conversion, the lasers are available from IR to DUV. The FTSS355-50 laser delivers 50 µJ pulse energy at a maximum repetition rate of 100 Hz and a pulse width of 1.3 ns, i.e. a peak pulse power of 60 kW. CryLaS lasers impress with their simple installation, service-free operation and long laser lifetime. They are the ideal tool for OEM applications and demanding scientific lab use.

The CryLaS Q series lasers are diode-pumped solid-state lasers (DPSS lasers) based on a microchip design. This consists of an Nd:YAG resonator with a directly coupled saturable absorber which works as a passive Q-switch. The compact housing and easy operation make the lasers an optimum light source for applications that require minimal housing dimensions with highest performance. Based on the 1064 nm fundamental, harmonics are generated using non-linear (NLO) crystals that allow a wide spectrum of laser wavelengths from 1064 nm to 213 nm. The FQSS213-Q3 laser emits pulses with approximately 1 ns pulse width at 213 nm, and can be modulated from single shot to 2.5 kHz. The pulse energy is 1.5 µJ at 1 kHz. CryLaS lasers impress with their easy installation, service-free operation and long service life. This makes them ideal for OEM applications and demanding laboratory setups.

The CryLaS Q series lasers are diode-pumped solid-state lasers (DPSS lasers) based on a microchip design. This consists of an Nd:YAG resonator with a directly coupled saturable absorber which works as a passive Q-switch. The compact housing and easy operation make the lasers an optimum light source for applications that require minimal housing dimensions with highest performance. Based on the 1064 nm fundamental, harmonics are generated using non-linear (NLO) crystals that allow a wide spectrum of laser wavelengths from 1064 nm to 213 nm. The FQSS213-Q4 laser emits pulses with approximately 1 ns pulse width at 213 nm, and can be modulated from single shot to 1 kHz. The pulse energy is 2.5 µJ. CryLaS lasers impress with their easy installation, service-free operation and long service life. This makes them ideal for OEM applications and demanding laboratory setups.

The CryLaS Q-series lasers are diode-pumped solid-state lasers (DPSS lasers) based on a microchip design. It consists of a Nd:YAG resonator with a directly coupled saturable absorber that works as a passive Q-switch. The compact housing and simple operation make the lasers an ideal light source for applications that require minimal housing dimensions with maximum performance. Based on the 1064 nm fundamental, non-linear optics (NLO optics) generate frequency multiples of this fundamental, covering a broad spectrum of laser wavelengths from 1064 nm to 213 nm. The DSS1064-Q2 laser emits pulses with a pulse width of approx. 1.5 ns at 1064 nm and can be modulated from single shot to 10 kHz. The pulse energy is 20 µJ. CryLaS lasers impress with their simple installation, service-free operation and long service life.

The CryLaS Q-series lasers are diode-pumped solid-state lasers (DPSS lasers) based on a microchip design. It consists of a Nd:YAG resonator with a directly coupled saturable absorber that works as a passive Q-switch. The compact housing and simple operation make the lasers an ideal light source for applications that require minimal housing dimensions with maximum performance. Based on the 1064 nm fundamental, non-linear optics (NLO optics) generate frequency multiples of this fundamental, covering a broad spectrum of laser wavelengths from 1064 nm to 213 nm. The FQSS266-Q2 laser emits pulses with a pulse width of approx. 1 ns at 266 nm and can be modulated from single shot to 10 kHz. The pulse energy is 0.8 µJ. CryLaS lasers impress with their simple installation, service-free operation and long service life. This makes them ideal for OEM applications and demanding laboratory setups.

The CryLaS Q-series lasers are diode-pumped solid-state lasers (DPSS lasers) based on a microchip design. It consists of a Nd:YAG resonator with a directly coupled saturable absorber that works as a passive Q-switch. The compact housing and simple operation make the lasers an ideal light source for applications that require minimal housing dimensions with maximum performance. Based on the 1064 nm fundamental, non-linear optics (NLO optics) generate frequency multiples of this fundamental, covering a broad spectrum of laser wavelengths from 1064 nm to 213 nm. The DSS1064-Q1 laser emits pulses with a pulse width of approx. 1.5 ns at 1064 nm and can be modulated from single shot to 20 kHz. The pulse energy is 10 µJ. CryLaS lasers impress with their simple installation, service-free operation and long service life.

The CryLaS Q-series lasers are diode-pumped solid-state lasers (DPSS lasers) based on a microchip design. It consists of a Nd:YAG resonator with a directly coupled saturable absorber that works as a passive Q-switch. The compact housing and simple operation make the lasers an ideal light source for applications that require minimal housing dimensions with maximum performance. Based on the 1064 nm fundamental, non-linear optics (NLO optics) generate frequency multiples of this fundamental, covering a broad spectrum of laser wavelengths from 1064 nm to 213 nm. The DSS1064-Q3 laser emits pulses with a pulse width of approx. 1.5 ns at 1064 nm and can be modulated from single shot to 2.5 kHz. The pulse energy is 50 µJ. CryLaS lasers impress with their simple installation, service-free operation and long service life.

The CryLaS Q-series lasers are diode-pumped solid-state lasers (DPSS lasers) based on a microchip design. It consists of a Nd:YAG resonator with a directly coupled saturable absorber that works as a passive Q-switch. The compact housing and simple operation make the lasers an ideal light source for applications that require minimal housing dimensions with maximum performance. Based on the 1064 nm fundamental, non-linear optics (NLO optics) generate frequency multiples of this fundamental, covering a broad spectrum of laser wavelengths from 1064 nm to 213 nm. The FTSS355-Q1 laser emits pulses with a pulse width of approx. 1 ns at 355 nm and can be modulated from single shot to 20 kHz. The pulse energy is 0.3 µJ. CryLaS lasers impress with their simple installation, service-free operation and long service life.

The CryLaS Q-series lasers are diode-pumped solid-state lasers (DPSS lasers) based on a microchip design. It consists of a Nd:YAG resonator with a directly coupled saturable absorber that works as a passive Q-switch. The compact housing and simple operation make the lasers an ideal light source for applications that require minimal housing dimensions with maximum performance. Based on the 1064 nm fundamental, non-linear optics (NLO optics) generate frequency multiples of this fundamental, covering a broad spectrum of laser wavelengths from 1064 nm to 213 nm. The FTSS355-Q2 laser emits pulses with a pulse width of approx. 1 ns at 355 nm and can be modulated from single shot to 10 kHz. The pulse energy is 3 µJ. CryLaS lasers impress with their simple installation, service-free operation and long service life.

The CryLaS Q-series lasers are diode-pumped solid-state lasers (DPSS lasers) based on a microchip design. It consists of a Nd:YAG resonator with a directly coupled saturable absorber that works as a passive Q-switch. The compact housing and simple operation make the lasers an ideal light source for applications that require minimal housing dimensions with maximum performance. Based on the 1064 nm fundamental, non-linear optics (NLO optics) generate frequency multiples of this fundamental, covering a broad spectrum of laser wavelengths from 1064 nm to 213 nm. The FTSS355-Q3 laser emits pulses with a pulse width of approx. 1 ns at 355 nm and can be modulated from single shot to 2.5 kHz. The pulse energy is 15 µJ @ 1 kHz. CryLaS lasers impress with their simple installation, service-free operation and long service life.

The CryLaS Q-series lasers are diode-pumped solid-state lasers (DPSS lasers) based on a microchip design. It consists of a Nd:YAG resonator with a directly coupled saturable absorber that works as a passive Q-switch. The compact housing and simple operation make the lasers an ideal light source for applications that require minimal housing dimensions with maximum performance. Based on the 1064 nm fundamental, non-linear optics (NLO optics) generate frequency multiples of this fundamental, covering a broad spectrum of laser wavelengths from 1064 nm to 213 nm. The DSS1064-Q4 laser emits pulses with a pulse width of approx. 1.5 ns at 1064 nm and can be modulated from single shot to 1 kHz. The pulse energy is 90 µJ. CryLaS lasers impress with their simple installation, service-free operation and long service life.

The eMOPA product series is based on a diode-pumped, passively Q-switched solid-state laser as the master oscillator and a downstream diode-pumped power amplifier with a patented optical design. Wavelengths from the DUV to the green spectral range can be generated for this series: 213 nm, 266 nm, 355 nm and 532 nm. The eMOPA266-40 emits pulses with a pulse width of around 1 ns and 40 µJ pulse energy. The average output power is 40 mW in transverse single-mode operation at a wavelength of 213 nm and peak pulse powers of >50 kW. The repetition rate can be adjusted from single shot to a maximum of 1 kHz by external triggering or the supplied software. The eMOPA is ideal for 24/7 industrial use and is primarily used in ophthalmology. By adapting the lasers to the requirements of our customers, a wide range of applications is possible, such as photoacoustics and ophthalmological markings.

The eMOPA product series is based on a diode-pumped, passively Q-switched solid-state laser as the master oscillator and a downstream diode-pumped power amplifier with a patented optical design. Wavelengths from the DUV to the green spectral range can be generated for this series: 213 nm, 266 nm, 355 nm and 532 nm. The eMOPA532-200 emits pulses with a pulse width of around 1 ns and 200 µJ pulse energy. The average output power is 200 mW in transverse single-mode operation at a wavelength of 532 nm and peak pulse powers of >130 kW. The repetition rate can be adjusted from single shot to a maximum of 1 kHz by external triggering or the supplied software. The eMOPA is ideal for 24/7 industrial use and is primarily used in ophthalmology. By adapting the lasers to the requirements of our customers, a wide range of applications is possible, such as photoacoustics and ophthalmological markings.

The CryLaS Q-series lasers are diode-pumped solid-state lasers (DPSS lasers) based on a microchip design. It consists of a Nd:YAG resonator with a directly coupled saturable absorber that works as a passive Q-switch. The compact housing and simple operation make the lasers an ideal light source for applications that require minimal housing dimensions with maximum performance. Based on the 1064 nm fundamental, non-linear optics (NLO optics) generate frequency multiples of this fundamental, covering a broad spectrum of laser wavelengths from 1064 nm to 213 nm. The FDSS532-Q1 laser emits pulses with a pulse width of approx. 1 ns at 532 nm and can be modulated from single shot to 20 kHz. The pulse energy is 2 µJ. CryLaS lasers impress with their simple installation, service-free operation and long service life.

The CryLaS High-Power series lasers are diode-pumped solid-state lasers (DPSS lasers) based on a microchip design. It consists of a Nd:YAG resonator with a directly coupled saturable absorber that works as a passive Q-switch. As the historically first development of CryLaS GmbH, the lasers are widely used in industrial and scientific application. They impress with their reliability, especially in the OEM business, and offer high pulse power with comparatively small housing dimensions. Thanks to frequency conversion, the lasers are available from IR to DUV. The FTSS355-50 laser delivers 50 µJ pulse energy at a maximum repetition rate of 100 Hz and a pulse width of 1.3 ns, i.e. a peak pulse power of 60 kW. CryLaS lasers impress with their simple installation, service-free operation and long laser lifetime. They are the ideal tool for OEM applications and demanding scientific lab use.