Power switches - Import export

The electronic temperature switch of BEDIA is fitted with thin-film resistor Pt 1000 in a bridge circuit. This sensor element provides close switch point tolerances and a quick response. Switch point and reset hysteresis may be selected within the admissible operating range when ordering so as to allow the monitoring of both very wide and very close temperature ranges. The switching output is protected from short-circuit and overload. The short-circuit current is limited by the output transistor switching off inthe event of a fault. It will automatically reset as soon as the fault has been remedied. The switch is available with ground-connected, plus-connected or potential-free DC switching output. The switch is open in the event of power failure or disconnection of the power supply, independed of the switching function. It is available both as normally open (NO) or normally closed (NC) switch.

These high-power bimetal operated temperature switches are available either with normally closed (NC) or normally open (NO) contact configuration. The robust round metal enclosure accommodates a resilient preloading disk, a bimetal disk and a silver contact. The compact switch system is covered by means of a plate which also carries a silver contact and is isolated from the enclosure by means of an isolating washer. The resilient preloading disk ensures excellent performance. The resilient preloading disk keeps the contact pressure constant throughout the entire temperature range of the BEDIA switch until switching occurs. The mechanically and electrically unloaded bimetal disk snaps over at a preset temperature, with either opening or closing the contact arrangement. The bimetal will only snap back to its initial condition after the temperature has dropped significantly.

Pneumatically operated angle seat flange valve for high switching powers. In stainless steel design also suitable for neutral and aggressive media. The angled seat design offers a high flow rate, the flange connection offers easy installation. Flange acc. to DIN EN 10921 Flange acc. to ANSI #150, ANSI#300 Limit switch Pilot valve Manual override . . .Piston actuator of Brass (chrome plated) Stainless steel Polymer Stainless steel diaphragm actuatorLow temperature version Pressure balanced version Degreased version, Silicon or PTFEfree version …

Rack mounting power supply, primary switched, remote controllable Input AC 100 - 240 V (wide range), Active-PFC For use in switch cabinets (TS35-rail acc. to EN 60715) Electrical safety / test report: IEC 60950-1, EN 60950-1, UL 60950-1, CSA 22.2 No. 60950-1, UL 508, IEC 62103, EN 50178 etc. EMC: EN 55011 Class B, EN 61000-3-2, EN 61000-6-2, EN 61204-3 No inrush current Floating relay contact Digital-I/O, Analog-IN (0 - 10 V or 4 - 20mA) Interface: RS-232 Very low stand-by-power, high efficiency (smooth behaviour across total input voltage range) Extensive protection for power output: short circuit, no-load, overvoltage, overtemperature

Rack mounting power supply, primary switched, remote controllable Input 380 - 500 V; 3 AC (wide range), Active-PFC For use in switch cabinets (TS35-rail acc. to EN 60715) Electrical safety / test report: IEC 60950-1, EN 60950-1, UL 60950-1, CSA 22.2 No. 60950-1, UL 508, IEC 62103, EN 50178 etc. EMC: EN 55011 Class B, EN 61000-3-2, EN 61000-6-2, EN 61204-3 No inrush current Floating relay contact, Digital-I/O, Analog-IN (0 - 10 V or 4 - 20 mA) Interface: RS-232 Very low stand-by-power, high efficiency (smooth behaviour across total input voltage range) Extensive protection for power output: short circuit, no-load, overvoltage, overtemperature

Rack mounting power supply, primary switched, remote controllable Input AC 100 - 240 V (wide range), Active-PFC For use in switch cabinets (TS35-rail acc. to EN 60715) Electrical safety / test report: IEC 60950-1, EN 60950-1, UL 60950-1, CSA 22.2 No. 60950-1, UL 508, IEC 62103, EN 50178 etc. EMC: EN 55011 Class B, EN 61000-3-2, EN 61000-6-2, EN 61204-3 Extensive protection for power output: short circuit, no-load, overvoltage, overtemperature Very low stand-by-power, high efficiency (smooth behaviour across total input voltage range) No inrush current Floating relay contact Digital-I/O, Analog-IN (0 - 10 V or 4 - 20mA) Interface: RS-232

Rack mounting power supply, primary switched, remote controllable Input AC 100 – 240 V (wide range), Active-PFC For use in switch cabinets (TS35-rail acc. to EN 60715) Electrical safety / test report: IEC 60950-1, EN 60950-1, UL 60950-1, CSA 22.2 No. 60950-1, UL 508, IEC 62103, EN 50178 etc. EMC: EN 55011 Class B, EN 61000-3-2, EN 61000-6-2, EN 61204-3 Extensive protection for power output: short circuit, no-load, overvoltage, overtemperature Very low stand-by-power, high efficiency (smooth behaviour across total input voltage range) No inrush current Floating relay contact Digital-I/O, Analog-IN (0 - 10 V or 4 - 20 mA) Interface: RS-232

Rack mounting power supply, primary switched, remote controllable Input AC 100-240V, Active-PFC wide range For use in switch cabinets (TS35-rail acc. to EN60715) Electrical safety / test report: IEC 60950-1, EN 60950-1, UL 60950-1, CSA 22.2 No. 60950-1, UL 508, IEC 62103, EN 50178 etc. EMC: EN 55011 Class B, EN 61000-3-2, EN 61000-6-2, EN 61204-3 Very low stand-by-power, high efficiency (smooth behaviour across total input voltage range) Floating relay contact, Digital-I/O, Analog-IN (0 - 10 V or 4 - 20 mA) Interface: RS-232 Extensive protection for power output: short circuit, no-load, overvoltage, overtemperature

Rack mounting power supply, primary switched, remote controllable Input 380 - 500 V; 3 AC (wide range), Active-PFC For use in switch cabinets (TS35-rail acc. to EN 60715) Electrical safety / test report: IEC 60950-1, EN 60950-1, UL 60950-1, CSA 22.2 No. 60950-1, UL 508, IEC 62103, EN 50178 etc. EMC: EN 55011 Class B, EN 61000-3-2, EN 61000-6-2, EN 61204-3 Very low stand-by-power, high efficiency (smooth behaviour across total input voltage range) No inrush current Floating relay contact, Digital-I/O, Analog-IN (0 - 10 V or 4 - 20 mA) Interface: RS-232 Extensive protection for power output: short circuit, no-load, overvoltage, overtemperature

Compacted material terminals made from Cu-ETP1 and Cu-OF1, in bare and tin-plated, nickel-plated and silver-plated upon request, in hard or soft annealed. Cross-section ranging from 1 mm² to 95 mm² depending on welding area. Compact welded terminals of different copper strands can be automated processed. A production of individual parts is possible as well as large-scale production. Resistance welded strands by LEONI are particularly suitable for high-voltage battery connectors, for high power connectors, for switch contacts and for special applications.

Flat led backlight system with border illumination for transmitted light- and contour applications for machine vision systems. At nearly all of our back lightings we are working with border illumination. The LEDs are not situated in the lighting area itwelf but below the unlighted edge. The light of the LEDs will be injected into the border of a flat light conductor and uncoupled equally via a calculated dot matrix system. This technique comes originally from the premises of planistar. The dot matric course are sitll being calculated from us an manufactured ba very precise UV print machines. So the square light has an very diffus and even light on the measuring surface. We can produce from very small led lights to very big monster lights every size you need for your vision light system. The high-power led backlights are with switch input for steady or flashing. The controller for the current are always inside.