Results for
BEDIA MOTORENTECHNIK GMBH & CO. KG
Germany
Temperature is one of the most measured physical parameters. Despite this, precise temperature measurement is one of the most difficult tasks in motor technology. To meet the constantly increasing requirements for improved motor performance, higher efficiency and reduced emissions, it is necessary to use reliable and precise sensors in modern motor control systems. The increased requirements over the last few years regarding measurement accuracy and reliability of temperature measurements has meant that many equipment operators must reconsider the suitability and performance capacity of their temperature measurement equipment. Resistant thermometers can be used between -200 °C and +850 °C. An important common property is that their output parameters are available in the form of electric signals that can be relatively easily transferred to measurement and control instruments for processing, storage and display.
Request for a quoteTISCHKÖNIG GMBH
Germany
Melamine table top: - chipboard according to DIN 68765, melamine resin coated on both sides and 2 mm ABS edge - the table top is hygienic, it is not harmful to food, and is simple to clean High-quality frame DT30: - stable steel construction, square columns with 2 motors - 3-stage lifting system (telescopic) - dual motors - height adjustment: 62 - 127 cm (without table top) - max. speed: 35 mm/s without load - collision protection - low noise level: < 45 dB - color: polyester powder-coated - LED display with 4 memory positions - plastic glides for safe standing - level compensation up to 10 mm Selection options: - table top color - table top thickness - dimension - frame color
Request for a quoteOKS SPEZIALSCHMIERSTOFFE GMBH
Germany
For fast determination of thermally-dependent interruptions in electrical circuits or components Avoidance of heat damage when soldering electrical components For heat protection of neighbouring components Shrinking of inner parts for removal of seized taper plugs, pins, plugs or bearing bushes Generation of shrink seats for assembly of inner parts For rapid temperature adjustment during materials testing For simulation of cold-starting conditions with motor-vehicle automatic starting systems Advantages and benefits Highly effective due to outstanding undercooling effect Excellently suited for simple cooling of parts Immediate cooling of smaller surfaces or parts down to –45°C depending on spraying duration Evaporates very quickly without residues Also provides good cleaning effect No negative affects on plastics and insulating materials
Request for a quoteOKS SPEZIALSCHMIERSTOFFE GMBH
Germany
Lubrication of rolling and friction bearings, as well as other machine elements at medium rotating speeds or sliding speeds in a broad temperature range For example, electric motors, drives, control systems and telecommunication and navigation systems under arctic conditions, Bowden cables and brake mechanisms in aircraft, sliding parts in shock-freezing systems etc. Lubricating grease for plastic/plastic and plastic/metal pairs and elastomers For plastic sliding coatings in bridge supports and as a parting agent in plastics processing Advantages and benefits Highly effective due to optimum formula Broad temperature range with a wide range of possible uses Excellently suited for lubricating plastics and elastomers Lubricating grease resistant to ageing, especially at low temperatures
Request for a quoteOKS SPEZIALSCHMIERSTOFFE GMBH
Germany
Lubrication of rolling and friction bearings subjected to high temperatures, corrosive environmental influences Lubrication of bearing points at furnace, cooling-bed and conveyor systems, motors and hot-air fans that are subjected to temperature stress Suitable for lubricating exhaust-gas fans Advantages and benefits Reduces wear and friction Good corrosion protection Excellent temperature resistance When operating temperature is exceeded, forms only minimal residues Good plastic and elastomer compatibility Good resistance against water influence and aggressive environmental influences For optimum effect, carefully clean the lubricating point, for example with OKS 2610/OKS 2611 universal cleaner. Before filling for first time, remove anti-corrosion agent. Fill the bearing such that all functional surfaces are certain of being greased. Fill normal bearings up to about 1/3 of the free space inside the bearing. Low-speed bearings (DN value < 50,000)
Request for a quoteDo you sell or make similar products?
Sign up to europages and have your products listed
JAKOB ANTRIEBSTECHNIK GMBH
Germany
• No external power sources needed • High holding forces • High stiffness for guaranteed performance • Kinetic energy from shock load is absorbed through dampening element • Integrated sensor for position control • High re-engagement accuracy • Automatic re-engagement • Reduced machine downtime for increased productivity • Available for all motor spindle designs and dmensions • Maintenance-freeMotor-Spindle Safety System
Request for a quoteResults for
Motor system - Import exportNumber of results
7 ProductsCountries
Company type