Forming technology - Import export

f your application requirements cannot be met by a standard SPIROL Spacer, our Application Engineering department will assist you in designing a tubular part that meets your specific needs. SPIROL specializes in replacing costly machined and cold-formed components with less expensive roll-formed product. SPIROL’s proprietary manufacturing technology enables the cost-effective production of special tubular products that meet the performance requirements of the comparatively more expensive alternatives.

Meta-Aramid Fiber with PTFE Blocking Agent and Run-In Lubricant Characteristics Wear resistant, universal packing for applications with abrasive content High cross section density and structural stability, yet elastic and pliable Low friction, low shaft wear (HRC 45 shaft shaft surface hardness is sufficient) Clean packing, no contamination of media Operating range Pressure [p max]: 25 bar, Velocity [v max]: 20 m/s Pressure [p max]: 100 bar, Velocity [v max]: 1.5 m/s Pressure [p max]: 100 bar Temperature: t = -100… +280 °C pH: 1 - 13 Density: 1.40 g/cm³ Main application Centrifugal pumps Mixer Agitators Autoclave Filter Refiner Kneader Paddle dryer Suitable for Pulp and paper industry Sugar industry Waste water technology Form of delivery This packing can be manufactured in dimensions from 10 to 40 mm as well as in intermediate, inch sizes and special measurements. Available from 4 to 9 mm in square X-Section. 04 - 09 mm on 1kg spool 10 - 15 mm on 2,5 kg spool 16 - 25 mm on...

Carbon Staple fiber with special Graphite Impregnation and silicon free Run In lubricant Practical useful application data: max. temperature: +200 °C Characteristics Volume stable, pressure stable High Cross section density due to special impregnation Excellent Value for money Graphitized all-round packing with Emergency run Capabilities Good wear resistance against abrasive and crystallizing products Recommended shaft surface hardness: HRC 45 Operating range Pressure [p max]: 20 bar, Velocity [v max]: 20 m/s Pressure [p max]: 250 bar, Velocity [v max]: 2 m/s Pressure [p max]: 150 bar Temperature: t = -50… +250 °C pH: 2 - 12 Density: 1.15 g/cm³ Practical useful application data: max. temperature: +200 °C Main application Centrifugal pumps Valves Mixer Kneader Agitators Suitable for Chemical industry Pulp and paper industry Waste water technology Community facilities Form of delivery This packing can be manufactured from 4 to 40 mm square as well as in intermediate, inch sizes...

Carbonized synthetic fiber with PTFE impregnation and run in lubricant Practical useful application data: max. temperature: +140 °C Characteristics Good flexibility Rot proof Form stable packing Good value for the money Recommended surface hardness HRC50 Operating range Pressure [p max]: 15 bar, Velocity [v max]: 15 m/s Pressure [p max]: 100 bar, Velocity [v max]: 2 m/s Pressure [p max]: 100 bar Temperature: t = -50… +200 °C pH: 3 - 12 Density: 1.30 g/cm³ Practical useful application data: max. temperature: +140 °C Main application Centrifugal pumps Mixer Kneader Agitators Refiner Autoclave Gate valves Filter Suitable for Pulp and paper industry Sugar industry Waste water technology General maintenance Form of delivery This packing can be manufactured from 4 to 40 mm square as well as in intermediate, inch sizes and special measurements. 04 - 09 mm on 1 kg spool 10 - 15 mm on 2,5 kg spool 16 - 25 mm on 5 kg spool Special length, pre-cut or die formed rings on request. 1 kg...

Carbonfiber with special impregnation and siliconfree dynamic high performance lubricant Practical useful application data: max. temperature: +250 °C max. pressure centrifugal pumps: 25 bar Characteristics Strong against abrasive mediums, yet low friction on shaft surface. Recommended shaft/sleeve hardness HRC 45 Volume stabile, minimal shrinkage, good heat conductivity Suitable as bullrings Operating range Pressure [p max]: 30 bar, Velocity [v max]: 25 m/s Pressure [p max]: 100 bar, Velocity [v max]: 2 m/s Pressure [p max]: 100 bar Temperature: t = -50… +300 °C pH: 2 - 12 Density: 1.45 g/cm³ Practical useful application data: max. temperature: +250 °C max. pressure centrifugal pumps: 25 bar Main application Boilerfeed pumps Refiner Suitable for Chemical industry Pulp and paper industry Power plant technology Boiler houses Form of delivery This packing can be manufactured from 4 to 40 mm square as well as in intermediate, inch sizes and special measurements. 04 - 09 mm on 1...

Synthetic Fiber Packing with PTFE Impregnation and Run-In Lubricant Characteristics Elastic and pliable Recommended shaft surface hardness: HRC 50 Resistance against rotting Structural stability Cost effective Operating range Pressure [p max]: 15 bar, Velocity [v max]: 12 m/s Pressure [p max]: 100 bar, Velocity [v max]: 1.5 m/s Temperature: t = -50… +140 °C pH: 3 - 12 Density: 1.30 g/cm³ Main application Centrifugal pumps Mixer Kneader Agitators Refiner Autoclave Gate valves Filter Suitable for Pulp and paper industry Sugar industry Waste water technology Form of delivery This packing can be manufactured from 4 to 40 mm square as well as in intermediate, inch sizes and special measurements. 04 - 09 mm on 1 kg spool 10 - 15 mm on 2,5 kg spool 16 - 25 mm on 5 kg spool Special length, pre-cut or die formed rings on request. 1 kg of packing of the following cross-sections corresponds to displayed meter lengths: Size mm["] Meter 4 48.1 5 [3/16"] 30.8 6 21.4 6.4 [1/4"] 19.1 8...

Beside the non-dressable CBN grinding tools, dressable grinding tools of leading manufacturers can be used on our machines, too. Vitrified bond aluminium oxide tools are dominant. Sintered aluminium oxide is preferred as the grinding tool for grinding of steel due to its resilience and grinding capability. Gray cast-iron can also be processed with normal aluminium oxide. The profiling of the grinding tools takes place via a machine-integrated CNC dressing unit. A diamond-plated, rotating dressing tool profiles the wheel in accordance with the respective gear parameters. The grinding tool is conditioned specifically for rough or finish grinding by selecting respective technological dressing parameters. Form consistency and cutting capacity of the grinding wheel is assured by repeated dressings, dependent on pre-defined stock removal rates. The automatic balancing produces smoother turning for larger grinding tools, and consequently, high gear quality. dressable CBN tools Single-layere