Cleaning media - Import export

The slimline probe LMP 305 with silicon stainless steel sensor is designed for continous level measurement in confined space conditions. Permissible media are clean or waste water and thin fluids. A piezoresistiv stainless steel sensor with low thermal error, an excellent linearity and a long term stability, is basis of LMP 305. Features: — nominal pressure: 0 ... 1 mH2O up to 0 ... 250 mH2O — accuracy: 0,35 % (opt. 0,25 %) FSO — diameter 19 mm for cramped areas e.g. 1" observation well — small thermal effect — excellent linearity — excellent long term stability Optional Features: — different kinds of cable — customer specific versions e.g. special pressure ranges

The slimline probe LMK 306 with ceramic sensor has been especially designed for the continuous level measurement at confined space conditions. Permissible media are clean or slightly contaminated water and thin fluids. Different cable sheath materials are available in order to achieve maximum media compatibility. Features: — nominal pressure: 0 ... 6 mH2O up to 0 ... 200 mH2O — accuracy: 0.5 % FSO — diameter 17 mm — excellent long term stability — suitable for hydrostatic level measurement e.g. 3/4" pipes — excellent linearity Optional Features: — different cable materials — customer specific versions e.g. special pressure ranges Preferred areas of use: — level measurement at confined space conditions — ground water monitoring — depth or level measurement in wells — drinking water abstraction — level measurement in open and closed tanks

Heat conductive ePTFE Yarn, PTFE fiber, Run-In Lubricant and elastic Silicon Tube Core Practical useful application data: max. temperature: +160 °C Characteristics Elevated heat conductivity For higher shaft speeds than S 6 SKV High chemical resistance and for clean media Operating range Pressure [p max]: 20 bar, Velocity [v max]: 10 m/s Temperature: t = -100… +280 °C pH: 1 - 14 Density: 1.60 g/cm³ Practical useful application data: max. temperature: +160 °C Main application Mixer Agitators Autoclave Kneader Paddle dryer Suitable for Rotating Equipment with higher surface speed radial run out Form of delivery This packing can be manufactured from 14 to 40 mm square as well as in intermediate, inch sizes and special measurements. 14 mm and above on 5 kg spool Special length, pre-cut or die formed rings on request. 1 kg of packing of the following cross-sections corresponds to displayed meter lengths: Size mm["] Meter 14 [9/16"] 3.2 15 2.8 16 [5/8"] 2.4 18 1.9 19 [3/4"]...

Meta-Aramid Fiber with PTFE Blocking Agent and Run-In Lubricant Characteristics Wear resistant, universal packing for applications with abrasive content High cross section density and structural stability, yet elastic and pliable Low friction, low shaft wear (HRC 45 shaft shaft surface hardness is sufficient) Clean packing, no contamination of media Operating range Pressure [p max]: 25 bar, Velocity [v max]: 20 m/s Pressure [p max]: 100 bar, Velocity [v max]: 1.5 m/s Pressure [p max]: 100 bar Temperature: t = -100… +280 °C pH: 1 - 13 Density: 1.40 g/cm³ Main application Centrifugal pumps Mixer Agitators Autoclave Filter Refiner Kneader Paddle dryer Suitable for Pulp and paper industry Sugar industry Waste water technology Form of delivery This packing can be manufactured in dimensions from 10 to 40 mm as well as in intermediate, inch sizes and special measurements. Available from 4 to 9 mm in square X-Section. 04 - 09 mm on 1kg spool 10 - 15 mm on 2,5 kg spool 16 - 25 mm on...

Acidic, neutral or alkaline wet media Aqueous media remove dirt particles from surfaces and rinse them off. Aqueous detergents disperse particles, and form or separate emulsions. They act on the surfaces of parts. If required, aqueous media can be used to alter the surface properties of parts by passivation (phosphatising), pickling, etc. In all applications, the treatment of the medium itself is of crucial importance. Aqueous media are powerful detergents. Solvents are wet media that are able to dissolve substances without actually reacting with them. The most commonly used cleaning solvents are hydrocarbons and modified alcohols with a flash point > 55°C, and halogenated hydrocarbons. Solvents remove dirt particles from surfaces and rinse them off. Advantages Short cycle times, energyefficient drying, low solvent consumption, long medium service life and easy treatment.

The compact KDA tunnel units cater for high throughput rates combined with excellent cleaning and drying. They have been designed for the treatment of parts of many different geometries and sizes. The KDA is available with belts of various widths (200/500/650 mm) and a range of features and accessories to cater for many different cleaning tasks. The KDA is available as 1, 2 and 3bath unit. Cleaning with aqueous media (acidic, neutral or alkaline) Spray cleaning unit for wide range of parts High throughput rate Compact, durable design Available as 1, 2 and 3bath unit with loading of the unit via Robot loading Manualm loading Construction side conveyor technology

For all cleaning methods, operators must comply with the applicable statutory regulations at local, national and international level. The handling and the treatment of the cleaning media are two important aspects that must be taken into account when assessing cleaning tasks and suitable methods.

The less space between the parts, the more difficult it is to remove particles and contaminants with a wet medium. The handling of the parts and the design of the parts carriers are therefore important aspects for optimised cleaning. Wet media are used in units with 1, 2, 3 or even more baths where the parts are cleaned and rinsed, and, if required, treated with preservation agents.

At our Centre of Competence measuring 1,100 square metres, there are more than 15 testing units at your disposal for the optimisation of your cleaning processes. Batch units for parts carriers up to 660 x 480 x 300 mm in size Tunnel cleaning unit Cleaning units for large parts up to approx. 2,100 mm in width and 1,500 kg in weight Test and compare various media and alternative cleaning processes Get to know efficient parts handling methods and equipment

The modular, preassembled PERO NEPTUN units are available at short notice for your specific application The NEPTUN is a universal machine for the cleaning of a wide range of parts. It guarantees maximum technical cleanliness, irrespective of the degree of contamination of the parts. The NEPTUNfeatures two baths and has been designed for reliable intermediate and final spray cleaning with aqueous media. Its touch panel control enables to devise and run customised cleaning programmes. Cleaning with aqueous media (acidic, neutral or alkaline) 660 x 480 x 300 mm 4 x 480 x 320 x 200 mm Powerful spray cleaning Universal machine Suitable for any cleanliness level from light dirt removal to high technical cleanliness Available as 2bath unit with loading of the unit via Manual loading table Manual charging unit Automatic charging unit

The ROTIMAT 3U is a universal machine for the cleaning of a wide range of parts. It guarantees maximum technical cleanliness, irrespective of the degree of contamination of the parts. It is equipped with two baths for cleaning, and subsequent iron phosphatising/rinsing, wherby each bath has its own pump cycle. The ROTIMAT 3U can be operated with standard baskets or customised parts carriers. Cleaning with aqueous media (acidic, neutral or alkaline) 660 x 480 x 300 mm 4 x 480 x 320 x 200 mm Spray cleaning for extra demanding applications Catering for wide range of parts Suitable for any cleanliness level from light dirt removal to high technical cleanliness Available as 2bath unit with loading of the unit via Manual loading table Manual charging unit Automatic charging unit

The ROTIMAT 1A has been designed for the spray cleaning of all workpieces that can be placed in the sturdy rotating basket. After production or repair, the workpieces and parts are cleaned with a hot aqueous cleaning medium that is sprayed onto the parts from all sides. The unit can be loaded from the front, or from the top, using lifting gear. The compact machine is equipped with four castors for easy relocation within the factory. Cleaning with aqueous media (acidic, neutral or alkaline) Universell cleaning unit for many different workpieces Compact portable unit with castors Drying without external heat input, or with optional extractor fan Available as 1bath unit with loading of the unit via Manual loading

Many years of expertise in system engineering for industrial cleaning technology Suitable for processes such as precleaning, postcleaning, conserving and drying Mobile and stationary multichamber cleaning systems for aqueous cleaning media Standardized or individual solutions tailored to the needs of the customer Manual or fully automated concepts Subsequently extendable and expandable Low operating costs with high availability Can be combined with stoba ECM/PECM systems Controller Siemens