Results for
JACOB GMBH
Germany
Waterproof enclosures with protection grades IP67 or IP68 for outdoor use are not automatically sealed against vapour and humid air. To avoid negative pressure, high humidity and condensation inside the enclosure a continuous Ventilation and pressure equilibrium is necessary. This function can be achieved by using a venting element made by Jacob. Features: - Continuous ventilation and adaptaion on the inner pressure - Hydrophobic and oleophobic PES- membrane - Body from stainless steel 1.4305 - Theoretical air flow through usable surface up to 75 l/h at Delta-p = 0,07 bar - Water entry pressure >= 0,83 bar (dynamic WEP, 30 seconds) - Temperature range -40°C / +100°C - Protection grade IP66 / IP68 - 0,6 bar (60 min.) / IP69
Request for a quoteJACOB GMBH
Germany
Waterproof enclosures with protection grades IP67 or IP68 for outdoor use are not automatically sealed against vapour and humid air. To avoid negative pressure, high humidity and condensation inside the enclosure a continuous Ventilation and pressure equilibrium is necessary. This function can be achieved by using a venting element made by Jacob. Features: - Continuous ventilation and adaptaion on the inner pressure - Hydrophobic and oleophobic PES- membrane - Polyamide material fulfills UL 94 V-0 and EN 45545-2, R22: HL3 / R23: HL3 - Theoretical air flow through usable surface up to 170 l/h at Delta-p = 0,07 bar - Water entry pressure >= 0,83 bar (dynamic WEP, 30 seconds) - Temperature range -40°C / +100°C - Protection grade IP66 / IP68 - 0,6 bar (60 min.) / IP69
Request for a quoteSOLARSPRING GMBH MEMBRANE SOLUTIONS
Germany
"Customized system engineering from pre-testing to full implementation. Starting with economic calculations and lab testing we will conceptualize and build your individual system for waste water- and drinking water treatment. Our team will install your system on site, monitor the commissioning and can also manage maintenance. "
Request for a quoteVELABRAN GMBH
Germany
Projektinfo: Busstation Theodor Heuss-Brücke VALMEX FR 900 Membrane 1150 m² Architekten: Zaeske & Partner, Wiesbaden Bauausführung: 2011 Terminal wird täglich von ca. 4000 Personen frequentiert
Request for a quoteMIR HAN BAU GMBH.
Germany
NECK/BACK BONE Pork Shoulder aka Pork Butt Picnic Ham Front Hock Pork Loin Pork Chops Baby Back Ribs Pork Belly Spareribs Sirloin Rear Leg Hock Frozen Pork Half Carcass Frozen Pork Leg Bone-in, Skin on Frozen Pork Leg Bone-in Skinless Frozen Pork Leg Boneless Skinless Frozen Pork Loin Bone-in Skinless Frozen Pork Loin Boneless Skinless Frozen Pork Shoulder Boneless, Skinless Frozen Pork Collar Boneless, Skinless Frozen Pork Loin Boneless, Skinless Frozen Pork Tenderloin Frozen Pork Belly Sheet Ribbed, Skin on Frozen Pork Spareribs Frozen Pork Back Fat Frozen Pork Cutting Fat Frozen Pork Tenderloin Frozen Pork Hind Feet Frozen Pork Ear Flap Frozen Pork Kidneys Frozen Pork Jowl Frozen Pork Heart Frozen Pork Liver Frozen Pork Neck Bones Frozen Pork Skin Frozen Pork Tongue Frozen Pork Throat Frozen Pork Snout Frozen Pork leg Frozen Pork Front Feet Frozen Pork Hind. Feet Frozen Pork Tails Frozen Pork Ear Flaps
Request for a quoteN&H TECHNOLOGY GMBH
Germany
We realize customer-specific membrane switch and advise you comprehensively on equipment requirements and technical features. On the basis of your sample, your specification or technical drawing, we will create an individual offer and support you during the project. We advise you on the selection of suitable materials and offer cost reduction options. We offer you an active co-operation in the development and construction and give suggestions for improvement. For an offer we need: •technical drawing, sketch or pattern •technical specifications, equipment extras •required amount Please send following informations to: info@nh-technology.de One of our engineering experts will contact you asap.
Request for a quoteOPTIGRÜN INTERNATIONAL AG
Germany
FLL-certified roof protection layer made of soft PVC for installation on non root-proof roofs, for forming a watertight and root-proof basin on green roofs with water accumulation and as water-proof and root-proof lining in planters.
Request for a quoteAQUACHEM GMBH SEPARATIONSTECHNIK
Germany
The AF filter presses from AQUACHEM are a further development of conventional chamber filter presses, which have been tried and tested in the industry for over a century. However, due to the degree of automation required and the increase in efficiency necessary nowadays, the technology we have had up until now is often no longer up to date. The design of the AF filter presses is based on the optimum interplay of the ?? individual assemblies of the filter press to ensure reliable, efficient and permanent operation without personnel being present. The automated flexibility of the product enables autonomous adjustment to changing conditions, such as concentration or even specific filter properties. We guarantee these properties and also availability. This is only possible because AQUACHEM and the AF-series possess the knowledge, an intelligent control system and the technology for maximum flexibility. Yes, this is a product with unique selling points – test it out yourself.
Request for a quoteLIPP GMBH BEHÄLTER UND SYSTEMLÖSUNGEN
Germany
LIPP® offers a wide range of Roofs and Covers for covering liquid, solid or gaseous media. They can be tailored and adjusted to each application. They include both roofs developed by LIPP® and also solutions designed by our partners. There are also simple foil roofs to choose from for gas storage facilities as well as singleskin, doubleskin or double diaphragm roofs. The LIPP® stainless steel diaphragm roof also offers a particularly highquality solution for the storage of volatile or explosive substances while the versatile LIPP® segment roof completes the range of covers.
Request for a quotePOREX TECHNOLOGIES GMBH
Germany
Strengthen and enhance membrane performance Customized and developed for specific end-use applications, POREX ® membrane support media are used as substrates for fragile membranes to provide structural strength and enhanced performance. Available in polyethylene (PE) and various customized geometries, our membrane support media: Support fragile membrane s with a strong and durable media. Enhance performance of specific end-use applications with custom designs Materials Offered Advanced porous materials (PE) Formats Available 3D molded shapes One piece solid and welded options including tubes and sheets Customization options for specific applications Request Sample ask an engineer
Request for a quoteFILTERTECHNIK JÄGER GMBH
Germany
Pleated Filter Cartridge Type: PPA Pleated PP-Membrane or nonwoven PP support nonwoven Hard cage Core + end caps made of 100 % polypropylene, meet requirements of FDA guidelines. Thermal welding processes seal all components No adhesives or extractable materials Version: DOE SOE 226 – O-Ring / Bayonet / Spear P7 SOE 222 – O-Ring / Flat P3 SOE 222 – O-Ring / Spear P8
Request for a quoteOPTIGRÜN INTERNATIONAL AG
Germany
Optigrun root protection membranes are used on non-root-resistant roof waterproofing under extensive and intensive roof greenings.
Request for a quoteAQUACHEM GMBH SEPARATIONSTECHNIK
Germany
The AQUACHEM LCM 320 (pocket press membrane) is ideal for mobile deployment on site on a suitable trolley and can be operated with up to 15 bar loading and 15 bar membrane squeezing. This machine can also be used as a testing filter press in the case in order to decide on the right fabric or to check the filterability of the suspension. Fully equipped, this compact press can manually implement functions that our fully automatic machines can do. The AQUACHEM LC 320 (pocket press chamber) is identical in design to the LCM 320 and differs only in its function as a chamber filter press (without membrane). The LC 470 is the more affordable, low-cost version of the EC-series. Main feature is the restriction of the feeding pressure to 7 bar. All other features are the same as the EC-series. This series is built in a compact design with a feeding pump and discharge manifold.
Request for a quoteBORSIG GMBH
Germany
BORSIG offers attractive process solutions for various gas separation applications in the fields of oil and gas production or refinery and process technology, such as BORSIG Hydrogen separation and BORSIG Fuel gas conditioning. This covers the treatment of gas streams for conditioning raw gas flows, recovery of specific components and the improvement of product quality to comply with customer gas specifications. Process concepts can be developed in addition to existing processes or as an alternative to conventional process solutions.
Request for a quoteAQUACHEM GMBH SEPARATIONSTECHNIK
Germany
Our testing filter presses for hire are available in various sizes. Whether in a container or as a mobile filter press, we're sure to find the right solution for you. Set-up and connection of the systems is easy to perform, and we are of course ready to assist you with commissioning.
Request for a quotePOREX TECHNOLOGIES GMBH
Germany
Filter industrial wastewater with tubular membrane filters For micro and ultrafiltration of industrial wastewater, our POREX® tubular membrane filters (TMF) are designed to fit new and existing tubular membrane systems. During operation, a fluid - such as chemically pre-treated wastewater - flows through the cross-flow membrane tubes at high velocity, sufficient to maintain turbulent flow. Best used for industries including electroplating, microchip manufacturing and zero liquid discharge systems, our tubular membrane filters: Fit new and current tubular membrane installations Are highly durable - Strong membrane-to-tube bond ensures long service life, and tough membrane withstands sharp particles and strong cleaning regimens. Enhance wastewater system performance with backwashable capability Multiple configuration options to meet low to high flow requirements
Request for a quoteBURSTER PRÄZISIONSMESSTECHNIK GMBH & CO KG
Germany
With its rugged housing and a stainless steel sensor element, the transducer is particularly robust and ideally suited to the harshest environments. This also means that the sensor can be installed anywhere with no effect on the measurement signal. The built-in instrumentation amplifier converts the sensor signals into noise-immune voltage signals or current signals that can be transmitted over relatively long distances. For high viscose materials, a front-level membrane M12 x 1 is available, and with this disruptive dead volumes can be expelled. The sensor has a small protected hole on the rear to allow measurement of atmospheric pressure (measurement type relative). For the absolute measurement option, the applied pressure is measured with respect to an enclosed vacuum. As an electrical connection, a DIN 43650A valve connector or an M12 x 1, 4-pin connection is available.
Request for a quoteDo you sell or make similar products?
Sign up to europages and have your products listed
BURSTER PRÄZISIONSMESSTECHNIK GMBH & CO KG
Germany
High-precision pressure sensors from the 8201 series provide exact measurements while exhibiting very little sensitivity to mechanical stresses. Their application therefore goes well beyond research and development laboratories. They are also outstandingly suited to industrial use in quality assurance or for measurement and control tasks in production. Their robust mechanical and electrical construction guarantees good long-term stability and high reliability, while being resistant to aggressive media – which can be measured in liquid or gaseous states. The structure of the sensors includes no mechanical moving parts, which is why they show so little sensitivity to impact and vibration. The pressure sensors can be configured with options to suit the user. Standard types are available ex-stock, and customized customer versions can also be provided. Aeras of application are: —Research and developmemt —Test rigs —Mechanical engineering —Plant control and monitoring
Request for a quoteBEKO TECHNOLOGIES GMBH
Germany
In addition to filtration, compressed-air drying contributes significantly to an increase in process reliability. Humidity in compressed-air systems causes corrosion, and promotes the growth of micro-organisms. In individual cases, condensate emerges at the point of use - an ongoing danger for the operational flow, for example because of failing pneumatic controls, increased wear and tear or because of other disturbances in the production process. With considerably enhanced process reliability, the DRYPOINT dryer technology offers decisive advantages for every field of application. The BEKO TECHNOLOGIES portfolio comprises application-optimised refrigeration, adsorption and membrane dryers for volumes up to 1,500 m³/h. This range of dryers is completed by heat-regenerated EVERDRY adsorption dryers which are designed for large volume flows up to 20,000 m³/h.
Request for a quoteGERBU BIOTECHNIK GMBH
Germany
Product group: DyesCellular Assays/ Detection-Labeling- kits Storing temperature: 2-8°C Shipping condition: ambient
Request for a quoteGERBU BIOTECHNIK GMBH
Germany
Product group: DyesCellular Assays/ Detection-Labeling- kits Storing temperature: 2-8°C Shipping condition: ambient
Request for a quoteGERBU BIOTECHNIK GMBH
Germany
Product group: DyesCellular Assays/ Detection-Labeling- kits Storing temperature: 2-8°C Shipping condition: ambient.
Request for a quoteKNÜPPEL VERPACKUNG GMBH & CO. KG
Germany
The membrane packaging fixes the product free-floating between two membrane pads that absorb shocks during transport and thus protect it from damage.
Request for a quoteBDSENSORS GMBH
Germany
The industrial pressure transmitter DMP 334 has been especially designed for use in hydraulic systems up to 2200 bar. The base element of DMP 334 is a thinfilm sensor, that is welded with the pressure port and meets high demands of foolproofness and reliability. All of characteristics and the excellent mesurement data of DMP 334 as well as distinguished offset stability offer a pressure transmiter with easy handling, reliability and robustness for hydraulic user. The DMP 334 is deliverable with pressure ports of extrem pressure technics. Features: — nominal pressure: 0 ... 600 bar up to 0 ... 2.200 bar — accuracy: 0.35 % FSO — pressure sensor welded — extremly robust and excellent longterm stability Optional Features: — IS-Version Ex ia = intrinsically safe for gases and dusts — pressure port M20 x 1.5 oder 9/16 UNF — adjustability of span and offset — different kinds of electrical connections
Request for a quoteBDSENSORS GMBH
Germany
The high-pressure transmitter type DMP 304 has been especially designed for applications with highest demand on precision and reliability. DMP 304 series is based on a compensated strain gauge, bonded onto a stainless steel diaphragm. Due to the rugged stainless steel housing usage under extreme conditions and in IS-required areas is no problem. Features: — nominal pressure: 0 ... 2000 bar up to 0 ... 6000 bar — accuracy: 0.5 % (opt. 0.25 %) FSO — adjustability of offset and span via front sided potentiometers — pressure port 9/16" UNF — 80 % calibration signal with MIL / Bendix plug Optional Features: — IS-version Ex ia = intrinsically safe for gases — pressure port M20 x 1.5 and M16 x 1.5 — accuracy according to IEC 60770: 0.25% FSO
Request for a quoteBDSENSORS GMBH
Germany
The pressure transmitter type DMP 333 has been especially designed for use in hydraulic applications with high static and dynamic pressure. The transmitter is characterized by an excellent long term stability, also under fast changing pressure as well as positive and negative pressure peaks. The modular concept of the device allows to combine different stainless steel sensors and electronic modules with a variety of electrical and mechanical versions.Thus a diversity of variations is created, meeting almost all requirements in hydraulic applications. Features: — nominal pressure: 0 ... 100 bar up to 0 ... 600 bar — accuracy:0.35 % (opt. 0.25 % / 0,1%) FSO — excellent long term stability, also with high dynamic pressure loads — insensitive to pressure peaks — high overpressure capability Optional Features: — IS-Version Ex ia = intrinsically safe for gases and dusts — SIL 2 version according to IEC 61508 / IEC 61511
Request for a quoteBDSENSORS GMBH
Germany
Contrary to the industrial pressure transmitter with analog signal, DCT 532 has a digital i²C-interface. i²C has a master-slave topology, whereby you can use up to 127 devices at one master. Due to the usage of high quality materials and components, DCT 532 is suitable for almost every industrial application, if medium is compatible with stainless steel 316L. The modular concept of the pressure transmitter allows customized electrical or mechanical connections, so it is easy to adapt the DCT 532 to different conditions on-site. Features: — nominal pressure: 0 ... 100 mbar bis 0 ... 400 bar — accuracy: 0.25% FSO — output signal: digital i²C — bus frequency max. 400 kHz — configuration of data format — interrupt signal — perfect thermal behaviour — excellent long term stability Optional Features: — pressure port G 1/2" flush from 100 mbar — pressure sensor welded — customer specific versions
Request for a quoteBDSENSORS GMBH
Germany
DCT 531 with RS485 interface uses the communication protocol Modbus RTU which has found the way in industrial communication as an open protocol. The Modbus protocol is based on a master Slave architecture with which up to 247 Slaves can be questioned by a master – the data will transfer in binary form. Due to the usage of high quality materials and components, DCT 531 is suitable for almost every industrial application, if medium is compatible with stainless steel 316L. The modular concept of the pressure transmitter allows customized electrical or mechanical connections, so it is easy to adapt the DCT 531 to different conditions on-site. Features: — nominal pressure: 0 ... 100 mbar up to 0 ... 400 bar — accuracy: 0.25% FSO — perfect thermal behaviour — excellent long term stability Optional Features: — pressure port G 1/2" flush from 100 mbar — pressure sensor welded — customer specific versions
Request for a quoteBDSENSORS GMBH
Germany
DMP 320 stands for speed and precision. With a response time of ≤ 0.5 msec and a sampling rate of 10 kHz, the pressure transmitter was designed for applications, in which an extremely fast and exact pressure measuring is required. Pressure curves, peaks and hits can be monitored and evaluated exactly. The signal processing of the sensor signal is done by newly developed digital electronics, which detect the signal with a sampling rate of 10 kHz. Sensor-specific deviations such as non-linearity, hysteresis and temperature errors are compensated actively. Features: — nominal pressure: 0 ... 100 mbar up to 0 ... 600 bar — accuracy: 0.1 % FSO — internal sample rate 10 kHz — excellent thermal behavior — excellent long term stability — extremely short response times ≤ 0.5 ms Optional Features: — customer specific versions
Request for a quoteResults for
Membranes - Import exportNumber of results
63 ProductsCountries
Company type
Category