Results for
IGUS® GMBH
Germany
E2 micro E-Chains® are very small, one-piece and two-piece (B07/B09) E-Chains® with a low weight and therefore ideal for highly dynamic applications. E2 micro E-Chains® are stable and available in many versions. igus® also offers numerous accessories and mounting options. "UPGrades" of the snap-open versions are available for many types; they are interchangeable among themselves and can thus be used as, among others, spare parts pack for new installation options. Other information Series 03 Inner height hi: 5 mm Inner widths Bi: 5 - 10 mm bending radii R: 10 - 28 mm Pitch: 10 mm E-Chain®, not-to-be-opened Series 04 Inner height hi: 7 mm Inner widths Bi: 7 - 30 mm bending radii R: 15 - 48 mm Pitch: 16,7 mm E-Chain®, not-to-be-opened Series 045 Inner height hi: 10,3 mm Inner widths Bi: 6 - 64 mm bending radii R: 18 - 38 mm Pitch: 13 mm E-Chain®, not-to-be-opened Series 05 Inner height hi: 10 mm Inner widths Bi: 6 - 64 mm bending radii R: 18 - 38 mm Pitch: 20 mm E-Chain®, not-to-be-opened Series 06 Inner height hi: 10,5 mm Inner widths Bi: 6 - 64 mm bending radii R: 18 - 38 mm Pitch: 20 mm E-Chain®, not-to-be-opened Series 08 Inner height hi: 15 mm Inner widths Bi: 10 - 50 mm bending radii R: 25 - 48 mm Pitch: 20 mm E-Chain®, not-to-be-opened Series B07 Inner height hi: 10,3 mm Inner widths Bi: 6 - 64 mm bending radii R: 18 - 38 mm Pitch: 20 mm E-Chain®, snap-open along the outer radius Series B09 Inner height hi: 14,3 mm Inner widths Bi: 16 - 40 mm bending radii R: 28 - 48 mm Pitch: 20 mm E-Chain®, snap-open along the outer radius Series 074 Inner height hi: 10.9 mm Inner widths Bi: 10 - 40 mm bending radii R: 18 - 38 mm Pitch: 20 mm E-Chain®, snap-open along the inner radius Series 094 Inner height hi: 14,3 mm Inner widths Bi: 10 - 40 mm bending radii R: 28 - 48 mm Pitch: 20 mm E-Chain®, snap-open along the inner radius Series E2.10, openable along the outside Inner height hi: 10 mm Inner widths Bi: 6 - 50 mm bending radii R: 10 - 38 mm Pitch: 20 mm e-chain®, snap-open outside Series E2i. 10, openable on the inside Inner height hi: 10 mm Inner widths Bi: 6 - 50 mm bending radii R: 10 - 38 mm Pitch: 20 mm e-chain®, snap-open inside Serie E2C. 10, closed Inner height hi: 10 mm Inner widths Bi: 6 - 50 mm bending radii R: 10 - 38 mm Pitch: 20 mm e-chain®, closed Series E2.15, openable along the outside Inner height hi: 15 mm Inner widths Bi: 10 - 50 mm bending radii R: 28 - 48 mm Pitch: 20 mm e-chain®, snap-open outside Series E2i. 15, openable on the inside Inner height hi: 15 mm Inner widths Bi: 10 - 50 mm bending radii R: 28 - 48 mm Pitch: 20 mm e-chain®, snap-open inside Serie E2C. 15, closed Inner height hi: 15 mm Inner widths Bi: 10 - 50 mm bending radii R: 28 - 75 mm Pitch: 20 mm e-chain®, closed iF-Design-Award for E2 micro Series 05 Clean room test on request Special design: Electrically conductive ESD/Atex versions on request UL94-V0 classification for Series 03 and Series 14 (more on request) 42 dB(A) determined at the igus® laboratory, v = 1.0 m/s unsupported, Series 06.10.038.0 E2 micro E-Chains® are very small, one-piece and two-piece (B07/B09) E-Chains® with a low weight and therefore ideal for highly dynamic applications. E2 micro E-Chains® are stable and available in many versions. igus® also offers numerous accessories and mounting options. "UPGrades" of the snap-open versions are available for many types; they are interchangeable among themselves and can thus be used as, among others, spare parts pack for new installation options. Series 03 Inner height hi: 5 mm Inner widths Bi: 5 - 10 mm bending radii R: 10 - 28 mm Pitch: 10 mm E-Chain®, not-to-be-opened Series 04 Inner height hi: 7 mm Inner widths Bi: 7 - 30 mm bending radii R: 15 - 48 mm Pitch: 16,7 mm E-Chain®, not-to-be-opened Series 045 Inner height hi: 10,3 mm Inner widths Bi: 6 - 64 mm bending radii R: 18 - 38 mm Pitch: 13 mm E-Chain®, not-to-be-opened Series 05 Inner height hi: 10 mm Inner widths Bi: 6 - 64 mm bending radii R: 18 - 38 mm Pitch: 20 mm E-Chain®, not-to-be-opened Series 06 Inner height hi: 10,5 mm Inner widths Bi: 6 - 64 mm bending radii R: 18 - 38 mm Pitch: 20 mm E-Chain®, not-to-be-opened Series 08 Inner height hi: 15 mm Inner widths Bi: 10 - 50 mm bending radii R: 25 - 48 mm Pitch: 20 mm E-Chain®, not-to-be-opened Series B07 Inner height hi: 10,3 mm Inner widths Bi: 6 - 64 mm bending radii R: 18 - 38 mm Pitch: 20 mm E-Chain®, snap-open along the outer radius Series B09 Inner height hi: 14,3 mm Inner widths Bi: 16 - 40 mm bending radii R: 28 - 48 mm Pitch: 20 mm E-Chain®, snap-open along the outer radius Series 074 Inner height hi: 10.9 mm Inner widths Bi: 10 - 40 mm bending radii R: 18 - 38 mm Pitch: 20 mm E-Chain®, snap-open along the inner radius Series 094 Inner height hi: 14,3 mm Inner widths Bi: 10 - 40 mm bending radii R: 28 - 48 mm Pitch: 20 mm E-Chain®, snap-open along the inner radius Series E2.10, openable along the outside Inner height hi: 10 mm Inner widths Bi: 6 - 50 mm bending radii R: 10 - 38 mm Pitch: 20 mm e-chain®, snap-open outside Series E2i. 10, openable on the inside Inner height hi: 10 mm Inner widths Bi: 6 - 50 mm bending radii R: 10 - 38 mm Pitch: 20 mm e-chain®, snap-open inside Serie E2C. 10, closed Inner height hi: 10 mm Inner widths Bi: 6 - 50 mm bending radii R: 10 - 38 mm Pitch: 20 mm e-chain®, closed Series E2.15, openable along the outside Inner height hi: 15 mm Inner widths Bi: 10 - 50 mm bending radii R: 28 - 48 mm Pitch: 20 mm e-chain®, snap-open outside Series E2i. 15, openable on the inside Inner height hi: 15 mm Inner widths Bi: 10 - 50 mm bending radii R: 28 - 48 mm Pitch: 20 mm e-chain®, snap-open inside Serie E2C. 15, closed Inner height hi: 15 mm Inner widths Bi: 10 - 50 mm bending radii R: 28 - 75 mm Pitch: 20 mm e-chain®, closed E-Chain® selection aids You can find the right E-Chain® quickly by entering concrete parameters and with the aid of a comparison table. Selection aids Installation instructions Joining and separating of the E2 micro E-Chain®. Assembly Instructions Application examples Applications in various industrial sectors. E2 micro For restricted spaces One and two-piece E-Chains®, from 5 mm inner height High torsion resistance Smallest inner heights and bending radii Mounting brackets with strain relief optional Small pitch for silent operation Cable-friendly interior Low weight Large pins for a long service life Favorable internal/external dimensions ratio B07/B09 in two parts - Can be folded out in outer radius due to integral hinges Typical industrial sectors and applications General construction machinery Models (micro E-Chain®), Automatic doors Vehicles Measuring machines Electronics Handling systems Pick and place robot iF-Design-Award for E2 micro Series 05 Clean room test on request Special design: Electrically conductive ESD/Atex versions on request UL94-V0 classification for Series 03 and Series 14 (more on request) 42 dB(A) determined at the igus® laboratory, v = 1.0 m/s unsupported, Series 06.10.038.0
Request for a quoteIGUS® GMBH
Germany
Other information E3.10 Inner height hi: 10 mm Inner widths Bi: 20 - 60 mm bending radii R: 15 - 48 mm Pitch: 16,7 mm E-Chain®. E3.15 Inner height hi: 15 mm Inner widths Bi: 20 - 60 mm bending radii R: 32 - 75 mm Pitch: 16,7 mm E-Chain®. E3.22 Inner height hi: 22 mm Inner widths Bi: 20 - 60 mm bending radii R: 44 - 75 mm Pitch: 16,7 mm E-Chain®. iF -Design Award 2005 IPA classification - Report IG0704-400:: ISO Class 1, according to DIN EN ISO 14644-1 for system E3, Series E3.15.040.075.0 at v = 0,5 m/s, 1 m/s, 2 m/s Other information E3.10 Inner height hi: 10 mm Inner widths Bi: 20 - 60 mm bending radii R: 15 - 48 mm Pitch: 16,7 mm E-Chain®. E3.15 Inner height hi: 15 mm Inner widths Bi: 20 - 60 mm bending radii R: 32 - 75 mm Pitch: 16,7 mm E-Chain®. E3.22 Inner height hi: 22 mm Inner widths Bi: 20 - 60 mm bending radii R: 44 - 75 mm Pitch: 16,7 mm E-Chain®. E-Chain® selection aids You can find the right E-Chain® quickly by entering concrete parameters and with the aid of a comparison table. Selection aids Installation instructions Opening and closing of the E-Chain®. Interior separation and strain reliefs. Assembly Instructions Application examples Applications in various industrial sectors and in the igus® test laboratory. E3 system E3: System for highly dynamic applications The cycle times are always shorter in the automation, whereas the requirements in noise reduction, service life, vibration dampening are always higher. For this wide area of small E-Chain®, igus® now introduces the E3 system product range that completely caters to these requirements: Extremely low noise operation (max. 38 dB(A)). The resilient element replaces pins and bores as fastener Modular chain made of three elements Cost-efficient crossbar and separator "on the band" Quicker and easier access to cables by the zipper system Good stability through stable, interlocked links Easy to shorten or lengthen Ideal for flat cables Accessories: Separators, integrated strain reliefs, mounting brackets Typical industrial sectors and applications Production and processing of semiconductors Optics Automatic insertion machines Materials handling technology Measuring technology Printer and plotter Clean room application General mechanical engineering iF -Design Award 2005 IPA classification - Report IG0704-400:: ISO Class 1, according to DIN EN ISO 14644-1 for system E3, Series E3.15.040.075.0 at v = 0,5 m/s, 1 m/s, 2 m/s
Request for a quoteIGUS® GMBH
Germany
Overview of E4.1 benefits Additional information Series E4.21 Inner height hi: 21 mm Inner widths Bi: 30 - 120 mm bending radii R: 38 - 200 mm Pitch: 30.5 mm E-Chain® with crossbars at every link Series E4.28 Inner height hi: 28 mm Inner widths Bi: 40 - 300 mm bending radii R: 55 - 250 mm Pitch: 46 mm E-Chain® with crossbars at every link Series E4.32 Inner height hi: 32 mm Inner widths Bi: 50 - 400 mm bending radii R: 63 - 300 mm Pitch: 56 mm E-Chain® with crossbars at every link Series E4.42 Inner height hi: 42 mm Inner widths Bi: 50 - 400 mm bending radii R: 75 - 350 mm Pitch: 67 mm E-Chain® with crossbars at every link Series E4.56 Inner height hi: 56 mm Inner widths Bi: 50 - 600 mm bending radii R: 135 - 500 mm Pitch: 91 mm E-Chain® with crossbars at every link Series E4.80 Inner height hi: 80 mm Inner widths Bi: 50 - 600 mm bending radii R: 150 - 1000 mm Pitch: 111 mm E-Chain® with crossbars at every link Series 1640 Inner height hi: 112 mm Inner widths Bi: 50 - 600 mm bending radii R: 200 - 600 mm Pitch: 143 mm E-Chain® with crossbars at every link E4.112 series Inner height hi: 112 mm Inner widths Bi: 50 - 600 mm bending radii R: 200 - 1000 mm Pitch: 143 mm E-Chain® with crossbars at every link E4.162 series Inner height hi: 162 mm Inner widths Bi: 200 - 600 mm bending radii R: 250 - 1000 mm Pitch: 200 mm E-Chain® with crossbars at every link Series 800 Inner height hi: 200 mm Inner widths Bi: 200 - 600 mm bending radii R: 325 - 1000 mm Pitch: 250 mm E-Chain® with crossbars at every link Series 840 Inner height hi: 204 mm Inner widths Bi: 100 - 563 mm bending radii R: 325 - 1000 mm Pitch: 250 mm E-Chain® with crossbars at every link Series E4.350 Inner height hi: 350 mm Inner widths Bi: 400 - 800 mm bending radii R: 500 - 1000 mm Pitch: 470 mm E-Chain® with crossbars at every link Series H4.32 Inner height hi: 32 mm Inner widths Bi: 50 - 400 mm bending radii R: 63 - 300 mm Pitch: 56 mm E-Chain® with crossbars at every other link Series H4.42 Inner height hi: 42 mm Inner widths Bi: 50 - 400 mm bending radii R: 75 - 350 mm Pitch: 67 mm E-Chain® with crossbars at every other link Series H4.56 Inner height hi: 56 mm Inner widths Bi: 50 - 600 mm bending radii R: 135 - 500 mm Pitch: 91 mm E-Chain® with crossbars at every other link Series H4.80 Inner height hi: 80 mm Inner widths Bi: 50 - 600 mm bending radii R: 150 - 1000 mm Pitch: 111 mm E-Chain® with crossbars at every other link Series H4.112 Inner height hi: 112 mm Inner widths Bi: 50 - 600 mm bending radii R: 200 - 1000 mm Pitch: 143 mm E-Chain® with crossbars at every other link Series R4.28 Inner height hi: 28 mm Inner widths Bi: 50 - 300 mm bending radii R: 63 - 250 mm Pitch: 46 mm E-Tube, swivel lid Series R4.32 Inner height hi: 32 mm Inner widths Bi: 50 - 300 mm bending radii R: 125 - 300 mm Pitch: 56 mm E-Tube, swivel lid Series R4.42 Inner height hi: 42 mm Inner widths Bi: 50 - 300 mm bending radii R: 125 - 350 mm Pitch: 67 mm E-Tube, swivel lid Series R4.56 Inner height hi: 56 mm Inner widths Bi: 75 - 462 mm bending radii R: 150 - 500 mm Pitch: 91 mm E-Tube, swivel lid Series R4.80 Inner height hi: 80 mm Inner widths Bi: 150 - 460 mm bending radii R: 200 - 1000 mm Pitch: 111 mm E-Tube, swivel lid Series R1608 Inner height hi: 112 mm Inner widths Bi: 200 - 400 mm bending radii R: 250 - 600 mm Pitch: 143 mm E-Tube, swivel lid R4.112 series Inner height hi: 112 mm Inner widths Bi: 200 - 400 mm bending radii R: 250 - 1000 mm Pitch: 143 mm E-Tube, swivel lid Assembly tool for E4-series For the practical opening and closing of the E4 series. Big savings in assembly time Assembly tool for E4-series IPA classification -Report IG 1303-640, tested E4.32.10.063.0 41 dB(A) determined at the igus® laboratory, v = 1.8 m/s unsupported ESD classification: Electrically conductive ESD/Atex versions on request System E4.1 proven in long travels e-tubes available as special design with HT material for 850°C hot chips Overview of E4.1 benefits Additional information Series E4.21 Inner height hi: 21 mm Inner widths Bi: 30 - 120 mm bending radii R: 38 - 200 mm Pitch: 30.5 mm E-Chain® with crossbars at every link Series E4.28 Inner height hi: 28 mm Inner widths Bi: 40 - 300 mm bending radii R: 55 - 250 mm Pitch: 46 mm E-Chain® with crossbars at every link Series E4.32 Inner height hi: 32 mm Inner widths Bi: 50 - 400 mm bending radii R: 63 - 300 mm Pitch: 56 mm E-Chain® with crossbars at every link Series E4.42 Inner height hi: 42 mm Inner widths Bi: 50 - 400 mm bending radii R: 75 - 350 mm Pitch: 67 mm E-Chain® with crossbars at every link Series E4.56 Inner height hi: 56 mm Inner widths Bi: 50 - 600 mm bending radii R: 135 - 500 mm Pitch: 91 mm E-Chain® with crossbars at every link Series E4.80 Inner height hi: 80 mm Inner widths Bi: 50 - 600 mm bending radii R: 150 - 1000 mm Pitch: 111 mm E-Chain® with crossbars at every link Series 1640 Inner height hi: 112 mm Inner widths Bi: 50 - 600 mm bending radii R: 200 - 600 mm Pitch: 143 mm E-Chain® with crossbars at every link E4.112 series Inner height hi: 112 mm Inner widths Bi: 50 - 600 mm bending radii R: 200 - 1000 mm Pitch: 143 mm E-Chain® with crossbars at every link E4.162 series Inner height hi: 162 mm Inner widths Bi: 200 - 600 mm bending radii R: 250 - 1000 mm Pitch: 200 mm E-Chain® with crossbars at every link Series 800 Inner height hi: 200 mm Inner widths Bi: 200 - 600 mm bending radii R: 325 - 1000 mm Pitch: 250 mm E-Chain® with crossbars at every link Series 840 Inner height hi: 204 mm Inner widths Bi: 100 - 563 mm bending radii R: 325 - 1000 mm Pitch: 250 mm E-Chain® with crossbars at every link Series E4.350 Inner height hi: 350 mm Inner widths Bi: 400 - 800 mm bending radii R: 500 - 1000 mm Pitch: 470 mm E-Chain® with crossbars at every link Series H4.32 Inner height hi: 32 mm Inner widths Bi: 50 - 400 mm bending radii R: 63 - 300 mm Pitch: 56 mm E-Chain® with crossbars at every other link Series H4.42 Inner height hi: 42 mm Inner widths Bi: 50 - 400 mm bending radii R: 75 - 350 mm Pitch: 67 mm E-Chain® with crossbars at every other link Series H4.56 Inner height hi: 56 mm Inner widths Bi: 50 - 600 mm bending radii R: 135 - 500 mm Pitch: 91 mm E-Chain® with crossbars at every other link Series H4.80 Inner height hi: 80 mm Inner widths Bi: 50 - 600 mm bending radii R: 150 - 1000 mm Pitch: 111 mm E-Chain® with crossbars at every other link Series H4.112 Inner height hi: 112 mm Inner widths Bi: 50 - 600 mm bending radii R: 200 - 1000 mm Pitch: 143 mm E-Chain® with crossbars at every other link Series R4.28 Inner height hi: 28 mm Inner widths Bi: 50 - 300 mm bending radii R: 63 - 250 mm Pitch: 46 mm E-Tube, swivel lid Series R4.32 Inner height hi: 32 mm Inner widths Bi: 50 - 300 mm bending radii R: 125 - 300 mm Pitch: 56 mm E-Tube, swivel lid Series R4.42 Inner height hi: 42 mm Inner widths Bi: 50 - 300 mm bending radii R: 125 - 350 mm Pitch: 67 mm E-Tube, swivel lid Series R4.56 Inner height hi: 56 mm Inner widths Bi: 75 - 462 mm bending radii R: 150 - 500 mm Pitch: 91 mm E-Tube, swivel lid Series R4.80 Inner height hi: 80 mm Inner widths Bi: 150 - 460 mm bending radii R: 200 - 1000 mm Pitch: 111 mm E-Tube, swivel lid Series R1608 Inner height hi: 112 mm Inner widths Bi: 200 - 400 mm bending radii R: 250 - 600 mm Pitch: 143 mm E-Tube, swivel lid R4.112 series Inner height hi: 112 mm Inner widths Bi: 200 - 400 mm bending radii R: 250 - 1000 mm Pitch: 143 mm E-Tube, swivel lid Assembly tool for E4-series For the practical opening and closing of the E4 series. Big savings in assembly time Assembly tool for E4-series IPA Classification Report IG 1303-640, tested series E4.32.10.063.0 E-Chain® selection aids You can find the right E-Chain® quickly by entering concrete parameters and with the aid of a comparison table. Selection aids Assembly instruction video Assembly video with accurate description for joining, splitting and opening e-chains® and e-tubes. Installation instructions Application examples Applications in various industrial sectors and in the igus® test laboratory. E 4.1 E4.1-E-Chain® with 4-piece structure Smooth, cable friendly inner surfaces Low noise operation through integrated "brake" on the radial stop dogs Sound dampers as an additional noise-reducing option Wide application range Numerous interior separation options Large accessory kits Widths up to 2000 mm through extension links To open on both sides Max. travel distance: Over 200 m Typical industrial sectors and applications: Krane Indoor Cranes Composting systems Sewage treatment plants Machine tools General mechanical engineering Materials-Handling Technology Refrigeration engineering Construction machinery Wood working Robotics and handling systems IPA classification -Report IG 1303-640, tested E4.32.10.063.0 41 dB(A) determined at the igus® laboratory, v = 1.8 m/s unsupported ESD classification: Electrically conductive ESD/Atex versions on request System E4.1 proven in long travels e-tubes available as special design with HT material for 850°C hot chips
Request for a quoteIGUS® GMBH
Germany
The troubleshooter for energy supply systems in the chip area - available in 4 sizes. Chips and dirt can affect the service life of cables and hoses significantly. With the RX system, igus® offers an extremely tight plastic e-tube that is nonetheless very easy to open. Snap-open in the outer radius A smooth, curved outer contour prevents chips from sticking Injection-molded "sealing lips" all around No holes, cracks, undercuts Series RX40 is IP40 tested (TÜV Saarland) Interior separation and guide trough available Covered pin/hole connection and stops "RBR" version with bending radius on both sides available Typical branches of industry Machine tools All applications in the direct chip sector Applications exposed to dust and dirt General mechanical engineering Dimensions and technical datas RX e-tubes RX32 Inner height hi: 42 mm Inner widths Bi: 80mm Bending radii R: 80 - 250 mm Pitch: 32 mm RX E-Tube RX40 Inner height hi: 52 mm Inner widths Bi: 100 mm bending radii R: 100 - 300 mm Pitch: 40 mm RX E-Tube RX48 Inner height hi: 62 mm Inner widths Bi: 120mm Bending radii R: 120 - 325 mm Pitch: 48 mm RX E-Tube RX56 Inner height hi: 73 mm Inner widths Bi: 140mm Bending radii R: 140 - 350 mm Pitch: 56 mm RX E-Tube RX56 High-temperature plastic version of the chip-proof RX energy tubes from stock - 850°C from 24h RX - from stock against hot chips red dot 2011: honourable mention for RX40 iF-Design-Award for RX e-tubes ESD classification: Electrically conductive ESD/Atex versions on request UL94-V0 classification on request e-tubes available as special design with HT material for 850°C hot chips The troubleshooter for energy supply systems in the chip area - available in 4 sizes. Chips and dirt can affect the service life of cables and hoses significantly. With the RX system, igus® offers an extremely tight plastic e-tube that is nonetheless very easy to open. Snap-open in the outer radius A smooth, curved outer contour prevents chips from sticking Injection-molded "sealing lips" all around No holes, cracks, undercuts Series RX40 is IP40 tested (TÜV Saarland) Interior separation and guide trough available Covered pin/hole connection and stops "RBR" version with bending radius on both sides available Typical branches of industry Machine tools All applications in the direct chip sector Applications exposed to dust and dirt General mechanical engineering Dimensions and technical datas RX e-tubes Chip tests in the igus® laboratory demonstrate the tremendous chip-proof properties of the igus® RX tube. Chip-proof - for all types of chips and applications RX32 Inner height hi: 42 mm Inner widths Bi: 80mm Bending radii R: 80 - 250 mm Pitch: 32 mm RX E-Tube RX40 Inner height hi: 52 mm Inner widths Bi: 100 mm bending radii R: 100 - 300 mm Pitch: 40 mm RX E-Tube RX48 Inner height hi: 62 mm Inner widths Bi: 120mm Bending radii R: 120 - 325 mm Pitch: 48 mm RX E-Tube RX56 Inner height hi: 73 mm Inner widths Bi: 140mm Bending radii R: 140 - 350 mm Pitch: 56 mm RX E-Tube RX56 High-temperature plastic version of the chip-proof RX energy tubes from stock - 850°C from 24h RX - from stock against hot chips Submersion test in water - Various tube types were submerged under water. The new RX tube needs over 30 seconds until it is filled up, thus proving its high leak tightness Y = time in seconds A = igus® products B = competitor Chip penetration test - Various types of tube were exposed to a defined quantity of chips. In the new RX tube, after 80,000 cycles only 0.2 g of chips were found in the interior Y = chip mass [g] A = igus® RX e-tube RX40.100.100 251.900 cycles B = igus® e-tubes 68.10.100.0 256.132 cycles C = test tube 01 250.907 cycles D = test tube 02* 2.600 cycles *Teststop after 2.600 cycles E = igus® products F = competitor E-Chain® selection aids You can find the right E-Chain® quickly by entering concrete parameters and with the aid of a comparison table. Productfinder Assembly instruction Dismantling / assembling a cover, replacing a chain link and assembling / inserting the RX tube. Assembly instruction Configure interior separation Define cables, select chain and configure interior separation. Now also for RX tubes! Interior separation configurator Application examples Applications in various industrial sectors. RX tubes Series RX - new chip-proof design, small pitch, removable cover 1 Chip-proof design without undercuts and edges 2 Excentric locking 3 Material igumid G 4 rounded shape 5 covered pin/hole connection RX tubes IP tested Technical report TÜV NORD red dot 2011: honourable mention for RX40 iF-Design-Award for RX e-tubes ESD classification: Electrically conductive ESD/Atex versions on request UL94-V0 classification on request e-tubes available as special design with HT material for 850°C hot chips
Request for a quoteIGUS® GMBH
Germany
Overview for E2/000 advantages Other information Series EF2.21 Inner height hi: 21 mm Inner widths Bi: 25 - 50 mm bending radii R: 35 - 180 mm Pitch: 33.3 mm E-Chain®, snap-open along the outer radius Series 1500 Inner height hi: 21 mm Inner widths Bi: 15 - 125 mm bending radii R: 35 - 180 mm Pitch: 33,3 mm E-Chain®, snap-open along the outer radius Series 1400 Inner height hi: 21 mm Inner widths Bi: 15 - 125 mm bending radii R: 35 - 180 mm Pitch: 33,3 mm E-Chain®, snap-open along the inner radius Series 1450 Inner height hi: 21 mm Inner widths Bi: 15 - 125 mm bending radii R: 35 - 180 mm Pitch: 33,3 mm Half energy tube, snap-open along the inner radius Series 1480 Inner height hi: 21 mm Inner widths Bi: 15 - 125 mm bending radii R: 35 - 180 mm Pitch: 33,3 mm Full energy tube, snap-open along the inner radius Series 2500 Inner height hi: 25 mm Inner widths Bi: 25 - 125 mm bending radii R: 55 - 250 mm Pitch: 46 mm E-Chain®, snap-open along the outer radius Series 2400 Inner height hi: 25 mm Inner widths Bi: 25 - 125 mm bending radii R: 55 - 250 mm Pitch: 46 mm E-Chain®, snap-open along the inner radius Series 2450 Inner height hi: 25 mm Inner widths Bi: 25 - 125 mm bending radii R: 100 - 250 mm Pitch: 46 mm Half energy tube, snap-open along the inner radius Series 2480 Inner height hi: 25 mm Inner widths Bi: 38 - 103 mm bending radii R: 100 - 250 mm Pitch: 46 mm Full energy tube, snap-open along the inner radius Series 2700 Inner height hi: 35 mm Inner widths Bi: 50 - 175 mm bending radii R: 63 - 250 mm Pitch: 56 mm E-Chain®, snap-open along the outer radius Series 2600 Inner height hi: 35 mm Inner widths Bi: 50 - 175 mm bending radii R: 63 - 250 mm Pitch: 56 mm E-Chain®, snap-open along the inner radius Series 2650 Inner height hi: 35 mm Inner widths Bi: 50 - 175 mm bending radii R: 100 - 250 mm Pitch: 56 mm Half energy tube, snap-open along the inner radius Series 2680 Inner height hi: 35 mm Inner widths Bi: 50 - 100 mm bending radii R: 100 - 250 mm Pitch: 56 mm Full energy tube, snap-open along the inner radius Series 3500 Inner height hi: 45 mm Inner widths Bi: 50 - 255 mm bending radii R: 75 - 300 mm Pitch: 67 mm E-Chain®, snap-open along the outer radius Series 3400 Inner height hi: 45 mm Inner widths Bi: 50 - 255 mm bending radii R: 75 - 300 mm Pitch: 67 mm E-Chain®, snap-open along the inner radius Series 3450 Inner height hi: 45 mm Inner widths Bi: 50 - 255 mm bending radii R: 150 - 300 mm Pitch: 67 mm Half energy tube, snap-open along the inner radius Series 3480 Inner height hi: 45 mm Inner widths Bi: 75 - 115 mm bending radii R: 150 - 300 mm Pitch: 67 mm Full energy tube, snap-open along the inner radius Series 255 Inner height hi: 24 mm Inner width Bi: 25 mm Bending radii R: 55 - 250 mm Pitch: 27.8 mm E-Chain®, snap-open along the outer radius CRC series. 255 Inner height hi: 24 mm Inner width Bi: 38-103 mm Bending radii R: 150 - 250 mm Pitch: 27.8 mm e-chain® Series CRC. 255 Assembly tool E"2/000 e-chains® - quick opening with assembly tools. Assembly tool Overview E2/000 bow chains Two-part - the E2 standard as clamp chain version Overview E2/000 bow chains ESD classification: Electrically conductive ESD/Atex versions on request IPA classification: ISO cleanroom class 3 (DIN 14644-1), at v=2 m/s, with standard material igumid G Series 2500.05.055.0 UL94 V0 classifications on request 46 dB(A) determined at the igus® laboratory, v = 1.0 m/s unsupported, e. g. Series 2600.05.075.0 iF Design Award for the E2/000 series EF2.21 Overview for E2/000 advantages Other information Series EF2.21 Inner height hi: 21 mm Inner widths Bi: 25 - 50 mm bending radii R: 35 - 180 mm Pitch: 33.3 mm E-Chain®, snap-open along the outer radius Series 1500 Inner height hi: 21 mm Inner widths Bi: 15 - 125 mm bending radii R: 35 - 180 mm Pitch: 33,3 mm E-Chain®, snap-open along the outer radius Series 1400 Inner height hi: 21 mm Inner widths Bi: 15 - 125 mm bending radii R: 35 - 180 mm Pitch: 33,3 mm E-Chain®, snap-open along the inner radius Series 1450 Inner height hi: 21 mm Inner widths Bi: 15 - 125 mm bending radii R: 35 - 180 mm Pitch: 33,3 mm Half energy tube, snap-open along the inner radius Series 1480 Inner height hi: 21 mm Inner widths Bi: 15 - 125 mm bending radii R: 35 - 180 mm Pitch: 33,3 mm Full energy tube, snap-open along the inner radius Series 2500 Inner height hi: 25 mm Inner widths Bi: 25 - 125 mm bending radii R: 55 - 250 mm Pitch: 46 mm E-Chain®, snap-open along the outer radius Series 2400 Inner height hi: 25 mm Inner widths Bi: 25 - 125 mm bending radii R: 55 - 250 mm Pitch: 46 mm E-Chain®, snap-open along the inner radius Series 2450 Inner height hi: 25 mm Inner widths Bi: 25 - 125 mm bending radii R: 100 - 250 mm Pitch: 46 mm Half energy tube, snap-open along the inner radius Series 2480 Inner height hi: 25 mm Inner widths Bi: 38 - 103 mm bending radii R: 100 - 250 mm Pitch: 46 mm Full energy tube, snap-open along the inner radius Series 2700 Inner height hi: 35 mm Inner widths Bi: 50 - 175 mm bending radii R: 63 - 250 mm Pitch: 56 mm E-Chain®, snap-open along the outer radius Series 2600 Inner height hi: 35 mm Inner widths Bi: 50 - 175 mm bending radii R: 63 - 250 mm Pitch: 56 mm E-Chain®, snap-open along the inner radius Series 2650 Inner height hi: 35 mm Inner widths Bi: 50 - 175 mm bending radii R: 100 - 250 mm Pitch: 56 mm Half energy tube, snap-open along the inner radius Series 2680 Inner height hi: 35 mm Inner widths Bi: 50 - 100 mm bending radii R: 100 - 250 mm Pitch: 56 mm Full energy tube, snap-open along the inner radius Series 3500 Inner height hi: 45 mm Inner widths Bi: 50 - 255 mm bending radii R: 75 - 300 mm Pitch: 67 mm E-Chain®, snap-open along the outer radius Series 3400 Inner height hi: 45 mm Inner widths Bi: 50 - 255 mm bending radii R: 75 - 300 mm Pitch: 67 mm E-Chain®, snap-open along the inner radius Series 3450 Inner height hi: 45 mm Inner widths Bi: 50 - 255 mm bending radii R: 150 - 300 mm Pitch: 67 mm Half energy tube, snap-open along the inner radius Series 3480 Inner height hi: 45 mm Inner widths Bi: 75 - 115 mm bending radii R: 150 - 300 mm Pitch: 67 mm Full energy tube, snap-open along the inner radius Series 255 Inner height hi: 24 mm Inner width Bi: 25 mm Bending radii R: 55 - 250 mm Pitch: 27.8 mm E-Chain®, snap-open along the outer radius CRC series. 255 Inner height hi: 24 mm Inner width Bi: 38-103 mm Bending radii R: 150 - 250 mm Pitch: 27.8 mm e-chain® Series CRC. 255 Assembly tool E"2/000 e-chains® - quick opening with assembly tools. Assembly tool Overview E2/000 bow chains Two-part - the E2 standard as clamp chain version Overview E2/000 bow chains IPA Classification Report IG 1303-640-1, tested 1500.050.038.0 at v = 0,5 / 1,0 / 2,0 ISO Class 2, according to DIN EN ISO 14644-1 E-Chain® selection aids You can find the right E-Chain® quickly by entering concrete parameters and with the aid of a comparison table. Selection aids Installation instructions Joining and separating of chain links, filling of the E-Tubes. Assembly Instructions System E2/000 Recommended installation accessories Application examples Applications in various industrial sectors and in the igus® test laboratory. System E2/000 The E2 standard Quickly opened from the right or left with a screwdriver or by hand - opening mechanism accessible from above Lightning fast installation using thumb - safe seat without additional closing mechanism The separators and interior separation sit safely, even when the E-Chain® is open Excellent mechanical stability; design and material provide long service life Typical industrial sectors and applications General construction machinery Materials handling technology Construction machinery Wood machines Machine tools Glass machines Plastic machines Long travels Semiconductor Theater and entertaining industry Vehicles And much more ESD classification: Electrically conductive ESD/Atex versions on request IPA classification: ISO cleanroom class 3 (DIN 14644-1), at v=2 m/s, with standard material igumid G Series 2500.05.055.0 UL94 V0 classifications on request 46 dB(A) determined at the igus® laboratory, v = 1.0 m/s unsupported, e. g. Series 2600.05.075.0 iF Design Award for the E2/000 series EF2.21
Request for a quoteTROTEC GMBH
Germany
Space-saving design, easy handlingand convincing functions Small enough to fit in everywhere. Light enough to be applied flexibly. Perfectly equipped to master every challenge. The TTK 28 E was designed specifically for small, heated rooms – and impresses with a high performance. Thanks to the compact dimensions of the dehumidifier TTK 28 E, you will always find a place where the TTK 28 E can do its job, even in the smallest room. It can, for example, keep living spaces and offices sized up to 15 m² dry reliably – with a daily dehumidification performance of up to 10 litres. A porthole allows for a clear view into the water tank to keep a constant eye on the filling level. Naturally, a filling level warning light warns of a full water tank and the overflow protection with automatic switch-off guarantees an immediate stop of operation.
Request for a quoteTROTEC GMBH
Germany
TTK 120 E Dehumidifier The TTK 120 E combines trendy design with advanced dehumidification technology in a durable housing construction. Thanks to its robust housing made of stainless steel the TTK 120 defies even the harshest application environments. This makes it to be a flexible dehumidifier from keeping dry living areas, archieves, store rooms as far as drying up after water damages. The change from one operation location to another can be easily achieved due to steering wheels and bar handles on both sides. Special features: SuperDry function (permanent drying) Automatic hygrostat controlled dehumidification Easy-care material combination with an eye-catching look Electronic automatic defrost Warning lamp: to indicate that the water tank is full Overflow protection with auto power off Carry handles, swivel casters Connectivity for an extern condensate drain
Request for a quoteGEPPERT RÜHRTECHNIK GMBH
Germany
The tote tank mixers CR-E are designed for operation on plastic containers with filling openings of 150 mm and volumes from 600 l up to 1,200 l. The customer may choose between various viscosity-related basic versions of fast-running and slow-running mixers with electric drives. The agitator shafts are connected to the drive shafts with sleeve couplings or borne within the gear’s hollow shaft (worm gears). The agitator shafts are balanced for concentric run after assembly. The mixer is mounted on a container traverse bridge, which is included in the scope of supply and clamped with a rapid fixing system to the cage frame of the IBC. The plastic bulk of the container is therefore not harmed by any static or dynamic loads by the agitator. The fixing of the traverse bridge is adjustable for various container models. The impellers are designed to fit through the filling opening 150 mm when being inserted. The electric container mixers are delivered with on-/off-switches with low-voltage breaker.
Request for a quoteGEPPERT RÜHRTECHNIK GMBH
Germany
CR-E - electric tote tank mixer for plastic IBCs The tote tank mixers CR-E are designed for operation on plastic containers with filling openings of 150 mm and volumes from 600 l up to 1,200 l. The customer may choose between various viscosity-related basic versions of fast-running and slow-running mixers with electric drives. The agitator shafts are connected to the drive shafts with sleeve couplings or borne within the gear’s hollow shaft (worm gears). The agitator shafts are balanced for concentric run after assembly. CR-E 6 0,75 The mixer is mounted on a container traverse bridge, which is included in the scope of supply and clamped with a rapid fixing system to the cage frame of the IBC. The plastic bulk of the container is therefore not harmed by any static or dynamic loads by the agitator. The fixing of the traverse bridge is adjustable for various container models. The impellers are designed to fit through the filling opening 150 mm when being inserted. The electric...
Request for a quoteFLUKE PROCESS INSTRUMENTS GMBH
Germany
Raytek GS150 thermal imaging systems enable automated quality control in glass bending, forming, annealing, and tempering processes. The GS150LE variant is especially designed for Low-E (low emissivity) glass / one-side coated flat glass. It features automatic emissivity correction. The systems are based on the Raytek MP150 infrared line scanner, which has a max. resolution of 1024 points per line, a max. 150 Hz scanning frequency, and an up to 90° wide field of view. SYSTEM PROPERTIES • Automated temperature monitoring • Visualization on PC • Ethernet TCP/IP interface integrated in the line scanning system • PC-independent alarm output • PC-independent analog outputs 3 x 4 – 20mA BENEFITS • Improve profitability and product quality • Reduce set-up time • Detect defects quickly • Automate quality monitoring for ISO9000 • Reduce scrap • Efficiently manage the heat balance in the oven • Automatically adjust the emissivity value when changing glass types or coatings
Request for a quoteRINGFEDER POWER TRANSMISSION GMBH
Germany
One-part design - Standard hub The coupling TSCHAN ® TNM E is a torsionally elastic and puncture-proof claw coupling. It balances out angular, radial and axial shaft misalignments within defined limits. The coupling transfers the torque via pressure loadable, elastic buffers of Perbunan (Pb) which are joined together as an intermediate ring. The elastic intermediate ring can cushion impacts and torsional vibrations; it is oil-tight and electrically conductive. The coupling is usable in every sense of rotation and installation position. TSCHAN ® TNM E One-part design - standard hub. Elastic intermediate ring in different hardnesses: standard Pb72, hard Pb82. General features Torsionally flexible, compensate for angular, radial and axial shaft misalignment Intermediate rings loaded in compression Elastomers available in various shore hardness degrees Suitable for temperatures from –30°C to +100°C The elastic ring can be replaced without having to move the coupled machines...
Request for a quoteGESCO-METALL GMBH SCHOTTENHAMML-BIEGETECHNIK
Germany
With this design E, the set frame and glazing frame is attached to the existing glass folding strip. Standard sizes “Nominal diameter” = Cut-out in the door panel Diameter = 200, 250, 300, 350, 400, 500 mm.
Request for a quoteBOLZ PROCESS TECHNOLOGY GMBH
Germany
Description ML001 Year of construction 1989 Manufacturer BOLZ-SUMMIX Machine no. M-9735 Product contacted material 316L Working volume / Total volume (l) 15 / 55 Total weight (kg) 600 Surface finish inside (µ) >0.8 Motors (kW) 1.1 Motors (EEx/ATEX) EEx e G3 Design operating Press. Vessel (bar) -1 / +1 Operating temperature Vessel (°C) Max. < 100 Design operating pressure Jacket (bar) 3 Accessories Vacuum pump, Condenser, Local control panel
Request for a quoteTAMPOPRINT GMBH
Germany
The RTI Compact II E is a single-color rotary pad printing machine. Designed as a manual workstation, it is primarily used to print circular cylindrical or flat parts. The basic body consists of an ergonomically designed base frame with protective enclosure and light curtain. The RTI COMPACT II E is consistently designed for ease of maintenance and short changeover times. User-friendliness and easy accessibility of the tampon roller characterize the machine. In addition, the RTI COMPACT II E is equipped with a residual ink pickup for automatic pad cleaning.
Request for a quoteMOSCA GMBH
Germany
• Dispenser variably mountable • 4 castors – Ø 125 mm (all lockable) • Parameter control panel for setting strapping parameters • Corrosion-resistant SoniXs Ultrasonic sealing unit in standard-6 version • Easy accessibility and tool-free dismantling of strap path components • Stepless turnable control panel (0 – 180°) for many- sided operation • Adjustable strap tension via control panel • Quick strap coil change • Strap end detection with ejection of remaining strap • Machine completely corrosion-resistant (main use of V4A stainless steel) • IP 56 protection class design • Sensitive components (e. g. motors) are equipped with additional covers • CE marking inclusive conformity declaration • Extremely low energy consumption
Request for a quoteSTRECKFUSS SYSTEMS GMBH & CO. KG
Germany
TYP C 043/E Cutting, stamping and bending device for axial components Description The Streckfuss machine Type C 043/E is designed, to cut stamp and bend axial leaded components for both horizontal and vertical mounting. To make the insertion of components with short leads into p. c. boards possible, the leads have to be cut to suitable length, bend to the required pitch and - if necessary- stamped. Both, suitable length and required pitch can be adjusted by adjusting screws. After this set- up the components can be processed. Option: the adjustments can be checked by a digital display. The stamping result for the leads depends on the used tool. These tools can be manufactured to meet customer requirements. The machine can be re- set for the different tools. The taped components can be processed automatically. The processing- speed is continuously variable. The tool change for different bending dimensions takes about 2 minutes. Components
Request for a quoteMOTAN-COLORTRONIC GMBH
Germany
Both the LUXOR E A and LUXOR EM A dryers with optional ETA plus® energy saving technology are specifically designed to supply consistently low dew-point air to one drying bin, while reducing energy consumption. The LUXOR E A dryer is designed for use with existing conveying systems or hopper loaders. Whereas the LUXOR EM A offers a machine dedicated solution with integrated dry air conveying for up to two processing machines and the drying bin. There are three sizes with drying bin capacities of 60, 100 and 150 litres. The LUXORnet controls utilise modern, flexible BUS-technology. As standard, the colour touch control manages the dry air generator, one drying bin and with the EM version, material conveying to one drying bin and two processing machines. The integration of dry-air conveying and material proportioning provides maximum flexibility and productivity.
Request for a quoteDo you sell or make similar products?
Sign up to europages and have your products listed
PULSARLUBE GMBH
Germany
The Pulsarlube E is designed to offer superior advantages in cost competitiveness and user friendliness over conventional gas type SPL units. The Pulsarlube E has a creative and innovative design which satisfies a wide variety of demands for industrial applications. It operates based on the proven technology of electrochemical reaction which generates inert Nitrogen (N2) gas through the systematic use of an electrolyte and electrical energy. Highly cost effective Easy to install and simple to operate Five available dispensing periods: 1, 3, 6, 9, and 12 months Convenient for use in confined spaces Durable and reliable engineering Transparent container for easy visual inspection of lubricant levels Resilient 1/4" NPT/BSPT compatible output thread
Request for a quoteResults for
E-design - Import exportNumber of results
19 ProductsCountries
Company type
Category