Bearing grease - Import export

Lubrication of highly stressed and relatively slowly running gears where due to leakage a grease must be used instead of oil For drives under high and shock load Chain lubrication of e.g. hollow pins, chains in the conveyor and transport field, under the influence of water and vapour and at higher operation temperatures Bearing lubrication of roller and plain bearings at annealing furnaces and drying equipments, manipulators and robots, conveyor and cooling systems, machines of preserve industry, steam sterilizers, etc. Advantages and benefits Best use in corrosive operation conditions with high operation temperatures and high pressure and shock load Economically due to optimum formulation Reduces wear and thereby downtime and enables long-term lubrication Ropy, strongly adhesive, temperature and water resistant, noise dampening, high-load and shock absorbing

Extreme-temperature grease on the basis of perfluorinated polyether oils (PFPE) for use in food processing technology at maximum loads and temperatures. Grease lubrication of friction and rolling bearings in the high-temperature range Application, for example at tunnel kiln cars, baking, burn-in and drying furnaces, hot gas units, reaction vessels, boiler plants, roller and conveyor rollers in continuous furnaces, etc. Use at bearing points under influence of chemicals/fuel Advantages and benefits Maximum water and steam resistance Extraordinary resistance to chemicals, for example to solvents, for example benzene, benzol, acetone, trichloroethylene and against inorganic acids, such as sulphuric acid, hydrochloric acid and nitric acid as well as stearic acids, alcohols and halogens Excellent plastic and elastomer compatibility For long-term lubrication of lubrication points subjected to high pressure up to 300°C

Grease lubrication of plain and rolling bearings in high-temperature range, where a mineral oil based grease cannot be used, e.g. on hot-air blowers and fans, autoclaves, drying ovens or systems in steelworks and foundries Advantages and benefits Drip-free hot bearing grease for a broad temperature range with high oxidations stability and moisture resistance Excellently suited for long-term lubrication of grease lubricating points subject to high-temperature loading Highly effective due to optimum high-performance formula Broad range of uses outside normal grease performance areas

Lubrication of friction, rolling and pivoting bearings, splined shafts, knockout spindles and sliding surfaces of all kinds under normal loads and all sliding speeds common for grease lubrication Supports sealing of bearings and corrosion protection Advantages and benefits Highly effective due to optimum combination of components Good resistance to pressure and water Fewer downtimes and repairs as a result of reduced wearing Resistant to ageing and oxidationFor highest effectiveness, carefully clean the lubrication point, for example with OKS 2610/OKS 2611 universal cleaner. Before filling for first time, remove anti-corrosion agent. Fill the bearing such that all functional surfaces are certain of being greased. Fill normal bearings up to about 1/3 of the free space inside the bearing. Low-speed bearings (DN value < 50,000) and their housings should be filled completely. The bearing and machine manufacturer's instructions should be observed.

Special grease for the long-term lubrication of ball and plain bearings where electrical charge is possible, e.g. in electric engines, foil- stretching and foil-printing machines, etc. Advantages and benefits Long-term lubrication grease with a wide temperature range and good corrosion protection The special lubricating concept makes sure that electrostatic charges in roller bearing applications are destaticized through the grease, so that local discharges are avoided Proven especially for the lubrication of roller bearings below 1 ampere

Lubrication of parts subject to high levels of stress such as plain, roller and rod-end bearings, spindles and guideways Advantages and benefits Highly suitable for high-stressed lubrication points Highly effective caused by optimal combination of components Saving of maintenance and lubrication costs by reducing downtimes and corrective maintenance Reduction of down times due to wearFor highest effectiveness, carefully clean the lubrication point, for example with OKS 2610 or OKS 2611 universal cleaner. Before filling for first time, remove anticorrosion agent. Fill bearing such that all functional surfaces are certain of being greased. Fill normal bearings up to about 1/3 of the free space inside the bearing. Low-speed bearings (DN value below 50 000) and their housings should be filled completely. The bearing and machine manufacturer´s instructions should be observed. Subsequent lubrication at the lubrication nipples by grease gun or by automatic lubrication system.

Electric motors for high speed application (approx. 6.000 up to approx. 30.000min1) need to be designed with special concern for bearings, greasing and ventilation.

Grease lubrication of plain and rolling bearings at high temperatures, e.g. in painting and drying ovens, converters, pouring ladles, heating systems, hot-air fans, charging cranes, vulcanising systems and electric motors Advantages and benefits Excellently suited for long-term lubrication of grease lubricating points subject to high-temperature loading Highly effective due to optimum solid lubricant formula Broad range of uses above normal grease performance areas Reduced maintenance and lubricant costs due to possible safety lubrication Drip-free hot bearing grease for long-term and safety lubrication in a broad temperature range For best results clean the lubricating point carefully. Clean with solvents like OKS 2610/OKS 2611 Universal Cleaner. Remove the corrosion protection ahead of the initial filling. Fill the bearings in a way that all the functional surfaces for sure get the grease.

Grease lubrication of friction and rolling bearings at low operating temperatures Grease lubrication of friction and rolling bearings at high speeds Grease lubrication of bearings with low coasting moments or low bearing play Advantages and benefits NSF H1 registered Low-viscosity, fully synthetic base oil ensures the functionality of the lubricating film up to -70°C Very good conveying capability in central lubricating systems also at low temperatures Clean the surfaces for optimal effect. Before filling for first time, remove anti-corrosion agent. Fill the bearing such that all functional surfaces are certain of being greased. Fill normal bearings up to about 1/3 of the free space inside the bearing

Lubrication of rolling and friction bearings subjected to high temperatures, corrosive environmental influences Lubrication of bearing points at furnace, cooling-bed and conveyor systems, motors and hot-air fans that are subjected to temperature stress Suitable for lubricating exhaust-gas fans Advantages and benefits Reduces wear and friction Good corrosion protection Excellent temperature resistance When operating temperature is exceeded, forms only minimal residues Good plastic and elastomer compatibility Good resistance against water influence and aggressive environmental influences For optimum effect, carefully clean the lubricating point, for example with OKS 2610/OKS 2611 universal cleaner. Before filling for first time, remove anti-corrosion agent. Fill the bearing such that all functional surfaces are certain of being greased. Fill normal bearings up to about 1/3 of the free space inside the bearing. Low-speed bearings (DN value < 50,000)

Lubrication of roller and plain bearings as well as of threaded spindles, gearwheels, worms and similar components Lubrication of spindle bearings in machine tools Advantages and benefits Allows high machine service lives due to low-wear operation and low lubrication frequencies Outstanding resistance in a wide temperature range, at high stresses and surface slide speeds as well as at vibrations Resistant to cold and hot water Excellent wear protection For highest effectiveness carefully clean the lubrication point, for example with OKS 2610/OKS 2611 universal cleaner. Before filling a bearing for first time, remove anti-corrosion agent. Fill the bearing such that all functional surfaces are certain of being greased. Fill normal bearings up to about 1/3 of the free space inside the bearing, high-speed bearings (DN value above 400,000) up to about 1/4. Low-speed bearings (DN value below 50,000) and their housings should be filled completely.

Grease lubrication of unsheltered parts subject to heavy loading and/or impacts, such as friction, rolling and pivoting bearings, splined shafts, knockout spindles, threaded spindles and sliding surfaces of all kinds For harsh operating conditions Advantages and benefits Excellently suited as a safety lubricating grease in mixed friction sector with especially good wear protection Effectively protects against corrosion Contains Mox-active to improve performance For best results clean the lubricating point carefully. Clean with solvents like OKS 2610/OKS 2611 Universal Cleaner. Remove the corrosion protection ahead of the initial filling. Fill the bearings in a way that all the functional surfaces for sure get the grease. Slow moving bearings(DN-value < 50,000) should be filled completely, normal moving bearings should be filled to 1/3 of the free inner housing space. Observe the instructions of the bearing or machine manufacturer. Relubrication with a grease gun on to the grease

Lubrication of friction, rolling and pivoting bearings, splined shafts, knockout spindles and sliding surfaces of all kinds under heavy loads and a broad temperature range, as well as all sliding speeds permissible for grease lubrication Advantages and benefits Modern grease with a wide range of applications Supports sealing of bearings Good corrosion protection Resistant to ageing and oxidation Good resistance to pressure and water Available in the 120 cm³ ChronoLube cartridge For optimum effect, carefully clean the lubricating point, for example with OKS 2610/OKS 2611 universal cleaner. Before filling for first time, remove anti-corrosion agent. Fill the bearing such that all functional surfaces are certain of being greased. Fill normal bearings up to about 1/3 of the free space inside the bearing. Low-speed bearings (DN value < 50,000) and their housings should be filled completely. The bearing and machine manufacturer's instructions should be observed. Subsequent lubrication

single inlet/outlet line or combined inlet/outlet line with stationary or rotating syphon pipe universal usecooling, heating, clamping series with ball bearings, graphite bushbearing or solid grease ballbearings bellows sealing available in stainless steel CDCartridgeDesign PRESSURE MAXIMUM 6,0 bar heat transfer oil 10,0 bar air nontoxic gases steam 17,0 bar water TEMPERATURE MAXIMUM 300 °C air heat transfer oil nontoxic gases steam vacuum water SPEED MAXIMUM 600 1/min DN 80 (3") DN 100 (4") DN 125 (5") SIZEDN 80 (3") DN 100 (4") DN 125 (5")

Pre-assembled pump kit for food and pharma in ex-version. The pump-kit is ideal for frequent medium changes and is suitable for conveying out of drums, IBCs or tanks. Due to the construction with mechanical seal, the pump can be easily and quickly taken apart into its two main components. This allows good cleanability. Comprising drum pump FP 430 Ex FOOD, outer tube stainless steel, commutator F 460 Ex, hose, hand nozzle, hose connection, compression gland and earth cable. Product attributes: - With mechanical seal for sealing the inner tube - Pump can be disassembled into two parts: inner tube cpl. and outer tube - Grease-lubricated shaft bearing Benefits: - Ideal for frequent medium changes, hardening media, fast drying media, crystallizing media - Can be taken apart into main components easily and quickly for cleaning - Compared to sealless pump higher service life on abrasive media - Appropriate for food contact acc. to EC 1935/2004 and FDA CFR 21

Pivot pins are found on shutoff devices such as spherical valves, butterfly valves, hollow jet valves and plunger valves. These valves are generally used for opening and closing and occasionally to control the flow rates by oscillating movement. The greaselubricated sliding bearing is protected against water infiltration by a seal on the inside. The seal also prevents the grease leaking into the inside to prevent water contamination. The MANOY® system seal WP, type 418, was developed for this application. To prevent leakage of grease from greased bearings, the unidirectional MANOY® system seal WP, type 456, is also installed.

Rolled composite plain bearing | Maintenance-free | Steel / graphite bronze | With embedded solid lubricants GAP-MET®/S is a maintenance-free composite plain bearing. However, oil or grease lubrication is possible. High load capacity and strength, for all slow movement types, suitable for contaminated environments, no moisture absorption, good chemical resistance. For technical details, please visit the product page on our website!

Wrapped composite sliding bearing with lubrication pockets/ copper-plated steel & AlSn20Cu | Low-maintenance | DIN 1494 / ISO 3547 For high sliding speeds, optimum sliding behaviour with good lubricant supply. BIV-MET®/A is a composite sliding bearing requiring maintenance; oil or grease lubrication is needed. For technical details, please visit the product page on our website!

The B80 KGK G1 series (with closed impeller) is a powerful and robust centrifugal submersible pump with plain bearings, drive lantern on roller bearings and IEC standard motor. The pumped liquid is conveyed from the tank via the radial pump outlet and the vertical riser pipe. Power is transmitted from the motor to the pump by means of a torsionally flexible, positive-locking coupling and is designed for continuous operation. * Suitable for flow rates up to 30 m³/h * equipped with a suction strainer as standard * suction pipe extension up to 2000 mm is possible * available in immersion depths from 500 - 4000 mm Features & advantages * No screws in contact with the medium * Vibration and oscillation-free operation * Long service life and operational reliability * Lifetime grease-lubricated roller bearings * Independent bearings for motor and pump * External flushing to protect the plain bearings with media containing solids

The B80 KGK G2 series (with open impeller) is a powerful and robust centrifugal submersible pump with plain bearings, drive lantern with roller bearings and IEC standard motor. The pumped liquid is conveyed from the tank via the radial pump outlet and the vertical riser pipe. Power is transmitted from the motor to the pump by means of a torsionally flexible, positive-locking coupling and is designed for continuous operation. *Suitable for flow rates up to 80 m³/h * equipped with a suction strainer as standard * suction pipe extension up to 2000 mm is possible * available in immersion depths from 500 - 4000 mm Features & advantages * No screws in contact with the medium * Vibration and oscillation-free operation * Long service life and operational reliability * Lifetime grease-lubricated roller bearings * Independent bearings for motor and pump * External flushing to protect the plain bearings with media containing solids

Lubrication of normal-load friction, rolling and pivoting bearings Lubrication of spindles and guides at machines Lubrication of moving parts at fine-mechanical devices as well as household appliances Advantages and benefits Lubrication when dark-coloured lubricants cannot be used Saving of maintenance and lubricant costs by reducing downtimes and corrective maintenance Waterproof Clean the lubricating points well for optimal effect. Before filling for first time, remove anti-corrosion agent. Fill the bearing such that all functional surfaces are certain of being greased. Fill normal bearings up to about 1/3 of the free space inside the bearing. Low-speed bearings (DN value below 50,000) and their housings should be filled completely. In as far as available, the bearing and machine manufacturer's instructions should be observed.

Our housings and their respective bearings form bearing units which have proven themselves in machines, plant and other equipment. Bearing housings are usually made of cast iron, on request we can deliver housings in cast steel and nodular graphite cast iron. As the bearings are usually lubricated with grease, and this first lubrication holds for quite a while, most housings don’t have re-lubrication holes. There are however, gates or markings present, so that lubrication holes can be fitted if necessary. When re-lubricating, it must be ensured that excess lubricant can escape. The bearing seating points in the housings are usually machined so that the bearings are movable, so they function as floating bearings. Fixed bearings are achieved by inserting fixing rings, if these are listed in the table. Fixing rings must be ordered separately. Housings without fixing rings are delivered as floating bearing models (L) or fixed bearing models (F).

The angle transducers have a magnetic scanning according to the HALL principle. Due to the robust design, critical and interference-free applications in harsh environments can be realized. They have a robust housing (wall thickness > 5 mm) made of aluminium or stainless steel, shaft and ball bearing made of stainless steel, shaft with flattening, rotor with shaft and permanent magnet mounted in prechamber, sensor circuit consisting of ASIC with Hall elements and interface electronics housed in closed main chamber. Two models are available: For low and high temperature applications. The model for low-temperature use is equipped with a special grease for bearings and shaft seal. Seals and shaft seal are made of PTFE. Cable gland with clamping jaw pressure screw and silicone seal. The model for high temperature use is without shaft seal. Under the rear cover there is a signal changeover switch (CW/CCW). On the side there is a preset button (4 mA) placed under a screw plug.

The angle transducers have a magnetic scanning according to the HALL principle. Due to the robust design, critical and interference-free applications in harsh environments can be realized. They have a robust housing (wall thickness > 5 mm) made of aluminium or stainless steel, shaft and ball bearing made of stainless steel, shaft with flattening, rotor with shaft and permanent magnet mounted in prechamber, sensor circuit consisting of ASIC with Hall elements and interface electronics housed in closed main chamber. Two models are available: For low and high temperature applications. The model for low-temperature use is equipped with a special grease for bearings and shaft seal. Seals and shaft seal are made of PTFE. Cable gland with clamping jaw pressure screw and silicone seal. The high temperature model is without shaft seal. Under the rear cover, there is a signal path switch (CW/CCW). On the side there is a preset button (4 mA) placed under a screw plug.

with hybrid spindle bearings and lifetime grease lubrication. Hybrid bearings with steelrings and ceramic balls ensure high lifetime and speed. The spindle is maintenance-free and requires no external service unit. The spindle nose air labyrinth seal reliably protects the bearings against the ingress of contamination and coolant. Spindles are not sold on the Webshop, but spindle inquiries are accepted. Below on this page are listed the available accessories for the HJN842 in the web shop.

with hybrid spindle bearings with lifetime grease lubrication. Hybrid bearings with steelrings and ceramic balls ensure high lifetime and speed. The spindle is maintenance-free and requires no external service unit. The spindle nose air labyrinth seal reliably protects the bearings against the ingress of contamination and coolant. Spindles are not sold on the Webshop, but spindle inquiries are accepted. Below on this page are listed the available accessories for the HJN828 in the web shop.

mit hybrid spindle bearings and lifetime grease lubrication. Hybrid bearings with steelrings and ceramic balls ensure high lifetime and speed. The spindle is maintenance-free and requires no external service unit. The spindle nose air labyrinth seal reliably protects the bearings against the ingress of contamination and coolant. Spindles are not sold on the Webshop, but spindle inquiries are accepted. Below on this page are listed the available accessories for the HJN860 in the web shop.

oddesse-drainage pumps are used for dewatering in the construction industry and in mining, water supply in industry and agriculture, irrigation and drainage of municipal, garden and domestic areas and so on. EXECUTIONS - Submersible, single-stage centrifugal pumps - Motor compartment sealing via two high-quality mechanical seals - Ball bearings with long life grease lubrication - Motor cooling through pumped medium that flows around it - Available with motor protection - Automatic level regulations is optional - Pressure port with quick-release coupling, flange, hose nozzle or Whitworth thread - High-quality materials for application in service, industrial and seawater PERFORMANCE RANGE Delivery volume Q = ... 450 m³/h Delivery height H = ... 65 m