Anchor - Import export

Features • Earthquake tested C1 and C2 • Fire resistance class R120 • Approved by the building authorities • Impact protection protects the thread • Immediately load-bearing • Extreme hold • Setting depth marking for visual inspection of installation Description & Area of Application • Galvanised bolt anchor, washer and hexagonal nut • Torque-controlled wall plug • Small axis and edge distances for near-edge fastenings and small anchor plates • Secure adherence to the required setting depth due to setting depth marking

To avoid thermal bridges Separation of the hot dip galvanised pin from building structure through rubber plug Rubber plug absorbs structure borne noise Installation can be made before or after plastering Including hot dip galvanised threaded pin with Torx drive and two flat nuts Available for: Insulation thickness between 100 and 200 mm We would be very pleased to support you with all your individual questions and suggestions regarding WUS. Give us a ring or leave a message indicating the information you need. We will contact you as quickly as possible. Your WUS team

Ø 17mm Suitable for: SDS - hammer drills We would be very pleased to support you with all your individual questions and suggestions regarding WUS. Give us a ring or leave a message indicating the information you need. We will contact you as quickly as possible. Your WUS team

fixing element for dropped ceilings european technical approval ETA-06/0240

The tie points for the one-sided tie rod equipment can be operated by just one person - this guarantees optimised working even with less manpower requirements and in confined spaces. The new system has the particular advantage of being able to be anchored either on one side or conventionally, depending on requirements.

plastic hollow body | pear-shaped | yellow | with eyelets oben und unten on top and bottom Anchor- and marker buoy | approx. 10kg buoyancy | 250mm Ø x 390mm length

10 mm | 12 mm | 14 mm Anchor rope | hand spliced with stainless steel thimble | 3-ply | length 30m Available in 3 diameters. One side of the rope with spliced eye, which comes with a stainless steel thimble. This article is ready to use and should not be missing on any boat. The UV resistant line does NOT float. Breakload: 10 mm diameter approx. 1590 kp 12 mm diameter approx. 2270 kp 14 mm diameter approx. 3180 kp

This stainless steel sleeve, specially-designed for our detachable ABS-Lock I anchor, is available in a variety of different lengths and can be installed and countered on steel structures. Our ABS-Lock I+II system has been awarded national technical approval (for 2 individuals) and can be sealed up following installation using the plastic cap provided. National technical approval ("abZ"): Z-14.9-688 (pls. observe the installation instructions provided in the "abZ") EN 795:2012, A + CEN/TS 16415:2017 Designed for steel structures For use in combination with our ABS-Lock I anchor

This detachable stainless steel anchor is used in combination with an ABS-Lock II sleeve and can be installed on a variety of different surfaces. It is designed to secure 2 individuals simultaneously, has been awarded national technical approval by the German Institute for Construction Technology (DIBt) and is frequently used to secure the area around a window. EN 795:2012, B + CEN/TS 16415:2017 Can be simply removed at the touch of a button Locking latch prevents accidental unlocking Combine with our ABS-Lock II matching sleeve

Use one of these collars to seal up an anchorage point with or without an additional supporting tube (Ø 16 und Ø 42 mm). This sealant collar is available in two finishes for use on a bitumen roof surface: Sanded or slated. The disc is 420 mm in diameter. We supply this collar with matching shrink tubing. Seal for bitumen roof surfaces Sanded or slated For Ø 16 mm and Ø 42 mm rods Shrink tubing included Disc diameter Ø 42 cm

Our ABS Therm thermal protective cover (330 mm) can be used to insulate an anchorage point or support in a lifeline system. The cover can be shortened and is available in two diameters (16 and 42 mm - inner diameter). Add an ABS Signal signal rod to easily locate your anchorage device in snow cover. 330 mm high – can be individually shortened onsite Installed on top of your roof membrane Thermal cover: Outer diameter 70 mm – designed for anchorage points and lifeline systems (Ø16 mm) Thermal cover: Outer diameter 100 mm – designed for systems using a supporting tube (Ø 42 mm)

This stainless steel anchorage point (Ø 16 mm) - designed to secure individuals - has been certified by the German Institute for Construction Technology (DIBt). It is installed in concrete using two-component adhesive and is suitable for installation on a roof surface or facade - on the ground, in a wall or overhead. National technical approval ("abZ"): Z-14.9-688 (pls. observe the provisions provided in the "abZ") EN 795:2012, A + CEN/TS 16415:2013 Concrete ≥ C20/25 Recommended accessories: Special adhesive WIT-VM-250 Important: When the device protudes ≥ 100mm above the subsurface in a wall/facade lifeline system (corner or end support), an additional supporting tube is required

Use our portable ABS-Lock I+II anchor system in remote and difficult-to-reach places with the help of this telescopic rod. Our ABS-Lock I TelePole is available in three different lengths: 58-98 cm, 160-290 cm and 210-390 cm. Telescopic rod for our ABS-Lock I model Available in 3 different lengths: 58-98 cm (Tele-1) 160-290 cm (Tele-3) 210-390 cm (Tele-4)

Simply screw this sleeve onto an ABS-Lock X-Durch anchorage point to facilitate installation: Thanks to this installation aid, you can simply pull the anchor up through the bore hole to complete the installation. Installation aid for installing an ABS-Lock X-Durch anchor Designed for pulling up the counter plate

Protect the upper thread and Data Matrix code of your ABS-Lock III-BE anchorage point from deformation through accidental hammer damage. Before hammering your anchor into place, simply screw this extension piece on top of the thread - and remove it afterwards to make room for your anchorage eyelet. Protects your ABS-Lock III-BE thread and Data Matrix code from accidental hammer damage Manufactured completely from stainless steel material

The innovative SANHA installation system NiroTherm® combines high-quality NiroTherm® press fittings with a black sealing ring made from EPDM (=ethylene propylene diem rubber) and NiroTherm® stainless steel system tubes. The system is produced from the material 1.4301 (AISI 304). Due to the well-known corrosion resistance of stainless steel, NiroTherm® offers installers therefore a real alternative compared to conventional steels when it comes to closed systems in humid atmospheres such as screed. Since it needs considerably less isolation against humidity*, the installation is faster and labour costs accordingly lower. In addition to the system description, NiroTherm® system press fittings are marked on the outside with a red dot. * This does not affect thermal insulation necessitated by national energy efficiency laws. NiroTherm® system pipe, material no. 1.4301, reduced wall thickness, in 6 m lengths, for cooling, compressed air, heating and industrial applications

"#quick and simple installation done by 1 person only within less than one minute, #one pieced anchor - no additional couplers or 45° - holders requested #no removing protruding tie rods - a minimum of refinishing only #installation into meshes more than 70 mm without any problem #no opening and welding reinforcements subsequently #position can be treated by a finishing trowel or a screed board and #recognized again reanchoring out of walls - installation in wall formwork - no more drilling through formwork panels!"

Fixation of slab stopend bars, trestles and angles,supports for climbing formwork, handrail holders

"#quick and simple installation done by 1 person only within less than one minute, #one pieced anchor - no additional couplers or 45° - holders requested #no removing protruding tie rods - a minimum of refinishing only #installation into meshes more than 70 mm without any problem #no opening and welding reinforcements subsequently #position can be treated by a finishing trowel or a screed board and #recognized again reanchoring out of walls - installation in wall formwork - no more drilling through formwork panels!"

The wedge anchor is hammered into the borehole, with the expansion clip resting against the borehole wall due to its internal stress. When the nut is tightened, the cone pulls into the expansion clip, spreads it and presses it against the building material.

Compound anchors are particularly suitable for applying high load values ​​with small edge and axial distances, as they anchor without expansion pressure. They can be used in dry and damp subsoil, as well as cost-effective and efficient for side-by-side assemblies.