Anchor - Import export

This detachable stainless steel anchor is used in combination with an ABS-Lock II sleeve and can be installed on a variety of different surfaces. It is designed to secure 2 individuals simultaneously, has been awarded national technical approval by the German Institute for Construction Technology (DIBt) and is frequently used to secure the area around a window. EN 795:2012, B + CEN/TS 16415:2017 Can be simply removed at the touch of a button Locking latch prevents accidental unlocking Combine with our ABS-Lock II matching sleeve

Use one of these collars to seal up an anchorage point with or without an additional supporting tube (Ø 16 und Ø 42 mm). This sealant collar is available in two finishes for use on a bitumen roof surface: Sanded or slated. The disc is 420 mm in diameter. We supply this collar with matching shrink tubing. Seal for bitumen roof surfaces Sanded or slated For Ø 16 mm and Ø 42 mm rods Shrink tubing included Disc diameter Ø 42 cm

Our ABS Therm thermal protective cover (330 mm) can be used to insulate an anchorage point or support in a lifeline system. The cover can be shortened and is available in two diameters (16 and 42 mm - inner diameter). Add an ABS Signal signal rod to easily locate your anchorage device in snow cover. 330 mm high – can be individually shortened onsite Installed on top of your roof membrane Thermal cover: Outer diameter 70 mm – designed for anchorage points and lifeline systems (Ø16 mm) Thermal cover: Outer diameter 100 mm – designed for systems using a supporting tube (Ø 42 mm)

This stainless steel anchorage point (Ø 16 mm) - designed to secure individuals - has been certified by the German Institute for Construction Technology (DIBt). It is installed in concrete using two-component adhesive and is suitable for installation on a roof surface or facade - on the ground, in a wall or overhead. National technical approval ("abZ"): Z-14.9-688 (pls. observe the provisions provided in the "abZ") EN 795:2012, A + CEN/TS 16415:2013 Concrete ≥ C20/25 Recommended accessories: Special adhesive WIT-VM-250 Important: When the device protudes ≥ 100mm above the subsurface in a wall/facade lifeline system (corner or end support), an additional supporting tube is required

This reinforced, stainless steel anchorage point - designed for concrete applications - does not create any tension in the substructure and is suitable for unprotected surfaces. It includes a base plate (150 x 150 mm) and a welded-on supporting tube (Ø 42 mm) for extra stability and is installed using the 4 anchor rods supplied. All you need is an installation depth of a mere 60 mm. EN 795:2012, A + CEN/TS 16415:2017 Base plate + welded-on supporting tube Concrete ≥ C20/25 For installation depths ≥ 60mm Recommended accessories: Special Adhesive WIT-VM-250 Incl. stainless steel installation set

Use our portable ABS-Lock I+II anchor system in remote and difficult-to-reach places with the help of this telescopic rod. Our ABS-Lock I TelePole is available in three different lengths: 58-98 cm, 160-290 cm and 210-390 cm. Telescopic rod for our ABS-Lock I model Available in 3 different lengths: 58-98 cm (Tele-1) 160-290 cm (Tele-3) 210-390 cm (Tele-4)

Simply screw this sleeve onto an ABS-Lock X-Durch anchorage point to facilitate installation: Thanks to this installation aid, you can simply pull the anchor up through the bore hole to complete the installation. Installation aid for installing an ABS-Lock X-Durch anchor Designed for pulling up the counter plate

Protect the upper thread and Data Matrix code of your ABS-Lock III-BE anchorage point from deformation through accidental hammer damage. Before hammering your anchor into place, simply screw this extension piece on top of the thread - and remove it afterwards to make room for your anchorage eyelet. Protects your ABS-Lock III-BE thread and Data Matrix code from accidental hammer damage Manufactured completely from stainless steel material

The innovative SANHA installation system NiroTherm® combines high-quality NiroTherm® press fittings with a black sealing ring made from EPDM (=ethylene propylene diem rubber) and NiroTherm® stainless steel system tubes. The system is produced from the material 1.4301 (AISI 304). Due to the well-known corrosion resistance of stainless steel, NiroTherm® offers installers therefore a real alternative compared to conventional steels when it comes to closed systems in humid atmospheres such as screed. Since it needs considerably less isolation against humidity*, the installation is faster and labour costs accordingly lower. In addition to the system description, NiroTherm® system press fittings are marked on the outside with a red dot. * This does not affect thermal insulation necessitated by national energy efficiency laws. NiroTherm® system pipe, material no. 1.4301, reduced wall thickness, in 6 m lengths, for cooling, compressed air, heating and industrial applications