Results for
Germany
We produce for the martitim needs: railings, tubes, handrails, fittings, stairs, floors, rope tensioner, shroud spanner, skirting boards, aeration, lifting rings, clamps, rod holders, anchors, big-sized parts, angles, tees, safeguarding, thimbles, pressing sleeves and much more... Take profit also from our 3D-printign service for plastic & silicon parts. We realize your individual demans!
Request for a quoteGermany
FX-C lifting magnets have a round, multipole clamping surface, designed for lifting rings, sleeves, bearing housings, flange plates and similar workpieces.The load specification is valid for full-surface mounting on workpieces which cover D inside to D outside (see table Dimensions), for workpieces with a smaller mounting surface an approximate maximum workpiece weight of 3.5 kg per cm² clamping surface can be calculated. For serial workpieces, a documented test should confirm the safety factor 3.
Request for a quoteGermany
These flange type units is made of stainless steel and fix the hub positively against their extended flange preventing axial movement during tightening. Applied wherever self-centering action and good concentricity of mounted components are essential and hubs with straight-thru bores are used. Available sizes: Metric series shafts from 20 mm to 150 mm dia. and Inch series for shafts from 1” to 4” diameter. Excellent concentricity and very easy to dismantle – these Locking Assemblies provide particularly good concentricity between the clamped parts. The flange is reinforced at the critical point, preventing bending or lifting of the inner ring during assembly and thereby ensuring easy dismantling. High rotation speed – the dimensional accuracy of the RfN 7013 Locking Assemblies allows their use in applications with higher rotational speeds. High radial loads – the material strength of the RfN 7013 Locking Assemblies makes them especially suitable for applications with high radial...
Request for a quoteGermany
These flange type units fix the hub positively against their extended flange preventing axial movement during tightening. Applied wherever self-centering action and good concentricity of mounted components are essential and hubs with straight-thru bores are used. Available sizes: Metric series shafts from 20 mm to 150 mm dia. and Inch series for shafts from 1” to 4” diameter. Excellent concentricity and very easy to dismantle – these Locking Assemblies provide particularly good concentricity between the clamped parts. The flange is reinforced at the critical point, preventing bending or lifting of the inner ring during assembly and thereby ensuring easy dismantling. High rotation speed – the dimensional accuracy of the RfN 7013 Locking Assemblies allows their use in applications with higher rotational speeds. High radial loads – the material strength of the RfN 7013 Locking Assemblies makes them especially suitable for applications with high radial loads. Axial hub positioning –...
Request for a quoteGermany
These Locking Assemblies are of single-taper design with a self-locking taper providing good self-centering action and concentricity, as well as increased torque capacity. A pre-centering hub section is not required. Integral push-off screws for disassembly are provided. This unit can be placed deep inside a bore due to it’s design. Available sizes: Metric series shafts from 20 mm to 150 mm dia. and Inch series for shafts from 1” to 4” diameter. Excellent concentricity and very easy to dismantle – these Locking Assemblies provide particularly good concentricity between the clamped parts. The flange is reinforced at the critical point. This prevents a bending and lifting of the inner ring during installation and therefore a good dismantling is ensured. Higher Rotation Speed – the Locking Assemblies remain true-to-form during assembly and so they are suitable in applications with higher rotational speeds. High radial loads – the material strength of the RfN 7013 Locking Assemblies...
Request for a quoteDo you sell or make similar products?
Sign up to europages and have your products listed
Germany
Swivel stools: 5-arm plastic base, black, or 5-arm polished aluminium base, friction braked double castors for smooth floors or for carpeting, height adjustment 500 mm to 690 mm by means of “anatomic-lift” gas spring, with hand ring release, chromium-plated column, seat upholstered with leatherette acc. to colour chart. Examination seats: specially designed upholstered seat with leatherette cover acc. to colour chart, with or without backrest, height adjustment from 490 to 690 mm by means of gas spring, with foot ring release. 5-arm base powder coated in grey aluminium RAL 9007, with antistatic plastic castors Ø 50 mm for smooth/hard floors or for carpeting, with perimetral black bumper protection Safe working load: 135 kg.
Request for a quoteGermany
Description Special purpose NC rotary table discontinuous serration ring design, non-lift type, Z=360 - worm gear i=180 - safe transport load: 2,500 kg - table plate dm 1,175mm, with through hole Ø 860 mm in the centre, with Ø 960H7 centering collar - horizontal use - max. table plate speed: 25 rpm(at n motor=4,500 rpm) and i=180 - safe axial load: 54,000 N - safe radial load: 54,000 N feature: - serration ring table, - monitoring of the following functions: Hirth serration system "unlocked" and Hirth serration system "locked"
Request for a quoteResults for
Lifting ring - Import exportNumber of results
8 ProductsCountries
Company type