Clamp rings - Import export

The tote tank mixers CR-M are designed for operation on stainless steel containers with filling openings of DN 400 mm and mixing volumes from 400 l up to 1,500 l. Depending on the viscosity of the mixing material, CR-Ms with fast running or gear reduced drives are available. The agitator shafts are connected to the drive shafts with sleeve couplings or borne within the gear’s hollow shaft (worm gear). The agitator shafts are balanced for concentric run after assembly. The mixer is mounted on the container’s manway lid, which is clamped with butterfly screws or a clamp ring. The manway lid is supplied by the container manufacturer or by the customer. The impellers are designed to fit through the filling opening DN 400 when being inserted. The electric container mixers are delivered with on-/off-switches with low-voltage breaker. The electric container mixers can also be supplied with frequency converter drives. All CR-M series mixers can be supplied as follows:

LRK-C mit Antrieb LRK-A Electrical tote tank mixers for stainless steel IBCs The LRK-C series tote tank mixer and their drive units LRK-A are a special solution designed for operation on stainless steel containers with filling openings of at least 400 mm and mixing volumes from 400 l up to 1,500 l. The customer may choose between various viscosity-related basic versions of fast-running and slow-running mixers with electric drives. The mixing unit that remains in the container is connected to the drive unit with a bayonet coupling and a clutch. The drive is dismountable so that one drive unit can be used for several mixer units interchangeable. The mixer is mounted on the container’s manway lid, which is clamped with butterfly screws or a clamp ring. The agitator shafts are borne in a bearing housing, which is welded into the container lid on the product side. The impellers are designed to fit through the filling opening DN 400 when being inserted. If required, the electric tote...

CRP-M - Pneumatic tote tank mixer for stainless IBCs The CRP-M tote tank mixers are featured with a pneumatic drive and were designed for the application in stainless steel tanks with filling openings of at least 400 mm and mixing volumes of 400 l to 1,500 l. The fast running pneumatic agitators are equipped with bearing and coupling housings. By means of the maintenance unit, pressurized air is enriched with oil for the vane drive. The mixer is mounted on the container’s manway lid, which is clamped with butterfly screws or a clamp ring. The manway lid is supplied by the container manufacturer or by the customer. The impellers are designed to fit through the filling opening of at least 400 mm when being inserted. All CRP-M series can be supplied as follows: Lid Muffler Explosion-protection design

CR-M - Electric tote tank mixer for stainless steel IBCs The tote tank mixers CR-M are designed for operation on stainless steel containers with filling openings of DN 400 mm and mixing volumes from 400 l up to 1,500 l. Depending on the viscosity of the mixing material, CR-Ms with fast running or gear reduced drives are available. The agitator shafts are connected to the drive shafts with sleeve couplings or borne within the gear’s hollow shaft (worm gear). The agitator shafts are balanced for concentric run after assembly. The mixer is mounted on the container’s manway lid, which is clamped with butterfly screws or a clamp ring. The manway lid is supplied by the container manufacturer or by the customer. The impellers are designed to fit through the filling opening DN 400 when being inserted. The electric container mixers are delivered with on-/off-switches with low-voltage breaker. The electric container mixers can also be supplied with frequency converter drives. All CR-M...

The CRP-M tote tank mixers are featured with a pneumatic drive and were designed for the application in stainless steel tanks with filling openings of at least 400 mm and mixing volumes of 400 l to 1,500 l. The fast running pneumatic agitators are equipped with bearing and coupling housings. By means of the maintenance unit, pressurized air is enriched with oil for the vane drive. The mixer is mounted on the container’s manway lid, which is clamped with butterfly screws or a clamp ring. The manway lid is supplied by the container manufacturer or by the customer. The impellers are designed to fit through the filling opening of at least 400 mm when being inserted. All CRP-M series can be supplied as follows: Lid Muffler Explosion-protection design

Two piece design similar to 7006, but extended with lower shaft and hub pressures. 7007 ECOLOC Is a modification of 7004 ECOLOC with all its positive features, but here - same as 7006 ECOLOC - the axial displacement during mounting is averted. Explanations L = Overall width L 1 = Overall width (without screws) L 4 = Installation length up to colar L 3 = Clamping length d = Inner ring diameter D = Outer diameter D 1 = Collar outer diameter

Three piece self-centering design for heavy duty torques. 7005 ECOLOC Three piece, self-centering, slitted locking assemblies for highest bending moments and torques. During assembly a minor axial displacement of the hub occurs. The front and rear thrust rings are separately released through release threads. Explanations L = Overall width L 1 = Overall width (without screws) L 3 = Clamping length d = Inner ring diameter D = Outer diameter

Extended version of the 7003 allowing for use with smaller hub diameters due to the reduced shaft and hub pressures. 7004 ECOLOC Is the extended design of series 7003 ECOLOC. Here, due to the low pressure the hub can be designed very cost-effective (small outer diameter). Explanations L = Overall width L 1 = Overall width (without screws) L 3 = Clamping length d = Inner ring diameter D = Outer diameter

Two piece design with slit and single taper and without flange can be completely recessed within a component’s hub. Axial position of component not fixed and may move during installation. 7003 ECOLOC Self-centering, two piece low-cost locking assemblies, which can be used - due to the slit - also at larger tolerances. The hub slightly positions during mounting towards the screw head. For disassembly only few release screws are required. Through optimised geometry of the flange, the deformation of the flange is significantly lower than with standard products. Explanations L = Overall width L 1 = Overall width (without screws) L 3 = Clamping length d = Inner ring diameter D = Outer diameter

CHARACTERISTICS For clamp mounting into the pipeline Efficient protection of dirt-sensitive system components during commissioning Low differential pressure Easy installation and replacement Material Certificates DIN EN 10204/3.1 for Clamp Collar OPTIONS For DIN and ASME flange connections Design for low temperature down to -50 ° C Design pressure up to 100 bar Stainless steel construction Reverse flow direction GENERAL The starting screen VAS is used for commissioning and starting a system in order to clean gas from coarse soiling such as welding bead, scale, grease, etc. After starting, the starting screen can be removed from the pipeline. The design is carried out as a welding design. FUNCTION The starting screen VAS consists of a supporting basket made of perforated sheet metal with a welded clamping ring. These are galvanized after assembly. On the outside of the support basket a stainless steel wire mesh is welded.