Custom pressure sensors - Import export

The pressure transmitter DMP 321 is the consistent further development of our in many applications approved DMP 331. It shows an improved signal behavior and sets new standards in the industrial class. Its metallic diaphragm made of stainless steel (1.4435 / 316L) offers a good corrosion resistance in many industrial processes. The modular device concept allows to combine different pressure ranges with a variety of electrical and mechanical connections.Thus a diversity of variations is created, meeting almost all requirements in industrial applications. Features: — nominal pressure: 0 ... 100 mbar up to 0 ... 600 bar — accuracy: 0.1 % / 0.25 % FSO — excellent thermal behavior — excellent accuracy — compact design Optional Features: — IS-version Ex ia = intrinsically safe for gases and dusts — pressure sensor welded — customer specific versions

DCT 531 with RS485 interface uses the communication protocol Modbus RTU which has found the way in industrial communication as an open protocol. The Modbus protocol is based on a master Slave architecture with which up to 247 Slaves can be questioned by a master – the data will transfer in binary form. Due to the usage of high quality materials and components, DCT 531 is suitable for almost every industrial application, if medium is compatible with stainless steel 316L. The modular concept of the pressure transmitter allows customized electrical or mechanical connections, so it is easy to adapt the DCT 531 to different conditions on-site. Features: — nominal pressure: 0 ... 100 mbar up to 0 ... 400 bar — accuracy: 0.25% FSO — perfect thermal behaviour — excellent long term stability Optional Features: — pressure port G 1/2" flush from 100 mbar — pressure sensor welded — customer specific versions

The pressure transmitter DMP 331 can be used in all industrial areas when the medium is compatible with stainless steel 1.4404 (316 L) or 1.4435 (316 L). Additional are different elastomer seals as well as a helium tested welded version available. The modulare concept of the device allows to combine different stainless steel sensors and electronic modules with a variety of electrical and mechanical versions.Thus a diversity of variations is created, meeting almost all requirements in industrial applications. Features: — nominal pressure: 0 ... 100 mbar up to 0 ... 60 bar — accuracy: 0.35 % (opt. 0.25 % / 0,1%) FSO — excellent thermal behavior — excellent accuracy — flush pressure port G 1/2" from 100 mbar Optional Features: — IS-version Ex ia = intrinsically safe for gases and dusts — SIL 2 according to IEC 61508 / IEC 61511 — pressure sensor welded — customer specific versions

The sensor technology of the DCT 533 is the same as those of the proven pressure transmitter DMP 331 / DMP 333, whereby the DCT 533 is suitable for almost every industrial application, if medium is compatible with stainless steel 316L. The modular concept of the pressure transmitter allows customized electrical or mechanical connections, so it is easy to adapt the DCT 533 to different conditions on-site. Features: — nominal pressure: 0 ... 100 mbar up to 0 ... 400 bar — accuracy: 0,35 % (opt. 0,25%) FSO — IO-Link according to specification V 1.1 — Data transfer 38.4 kBaud — Smart sensor profile — perfect thermal behaviour — excellent long term stability Optional Features: — pressure port G 1/2" flush from 100 mbar — pressure sensor welded — customer specific versions

Contrary to the industrial pressure transmitter with analog signal, DCT 532 has a digital i²C-interface. i²C has a master-slave topology, whereby you can use up to 127 devices at one master. Due to the usage of high quality materials and components, DCT 532 is suitable for almost every industrial application, if medium is compatible with stainless steel 316L. The modular concept of the pressure transmitter allows customized electrical or mechanical connections, so it is easy to adapt the DCT 532 to different conditions on-site. Features: — nominal pressure: 0 ... 100 mbar bis 0 ... 400 bar — accuracy: 0.25% FSO — output signal: digital i²C — bus frequency max. 400 kHz — configuration of data format — interrupt signal — perfect thermal behaviour — excellent long term stability Optional Features: — pressure port G 1/2" flush from 100 mbar — pressure sensor welded — customer specific versions

The electronic pressure switch DS 400 is the successful combination of — intelligent pressure switch — digital display and has been specially designed for numerous applications in various industrial sectors. As standard the DS 400 offers a PNP contact and a display module, which is mounted rotable in the ball housing. Additional optional versions like e.g. an intrinsically safe version, a second contact and an analogue output complete the profile. Features: — nominal pressure: 0 ... 100 mbar up to 0 ... 600 bar — accuracy: 0.35 % (opt. 0.25 %) FSO — indication of measured values on a 4-digit LED display — rotatable and configurable display module Optional Features: — IS-Version Ex ia = intrinsically safe for gases — pressure sensor welded — customer specific versions

The electronic pressure switch DS 200 is the successful combination of — intelligent pressure switch — digital display and has been specially designed for applications in various industrial sectors. As standard the DS 200 offers a PNP contact and a rotatable display module with 4-digit LED display. Optional versions like e.g. an intrinsically safe version, max. 4 contacts and an analogue output complete the profile. Features: — nominal pressure: 0 ... 100 mbar up to 0 ... 600 bar — accuracy: 0.35 % (opt. 0.25 %) FSO — indication of measured values on a 4-digit LED display — rotatable and configurable display module — 1, 2 or 4 independent PNP contacts, freely configurable — configurable contacts (switch on / switch off points, hysteresis / window mode, switch on / switch off delay) Optional Features: — IS-version Ex ia = intrinsically safe for gases — pressure sensor welded — customer specific versions

High-precision pressure sensors from the 8201 series provide exact measurements while exhibiting very little sensitivity to mechanical stresses. Their application therefore goes well beyond research and development laboratories. They are also outstandingly suited to industrial use in quality assurance or for measurement and control tasks in production. Their robust mechanical and electrical construction guarantees good long-term stability and high reliability, while being resistant to aggressive media – which can be measured in liquid or gaseous states. The structure of the sensors includes no mechanical moving parts, which is why they show so little sensitivity to impact and vibration. The pressure sensors can be configured with options to suit the user. Standard types are available ex-stock, and customized customer versions can also be provided. Aeras of application are: —Research and developmemt —Test rigs —Mechanical engineering —Plant control and monitoring

Model number 8201 precision pressure sensors are robust, economical, and are available in standard measuring ranges. Their good technical specification and high reliability make them optimum for measuring pressure in all fields of machine construction, process technology, as well as in measurement and control technology. The pressure transducers are easy to handle and immune to shock loads and vibrations as they are designed without moving parts. All pressure transducers without an internal amplifier have a standardized output signal of 1.0 mV/V. This enables the user to change a transducer in a measuring chain as liked without following readjustment of the electronic. Customized designs are available on request. Aeras of application are: —Hydraulic or pneumatic machines —Mechanical engineering —Plant control and monitoring The measuring element of the precision pressure transducer consists of a diaphragm.

The Suvis GmbH offers flat pressure sensors (see photograph), which we produce ourselves and which can be used for classical static pressure measurements on solid surfaces like automobile frames. The flat pressure sensors are applied especially in cases where one cannot place a borehole in the respective surface. Hence, flat pressure sensors represent “transportable” static pressure boreholes, which one can glue on the surface of the flow body. The photo shows typical flat pressure probes. Typical dimensions are 17 mm (diameter of the flat disc) and 0,5 mm as diameter of the pressure borehole. The disc consists of bronze, while the measurement tube is made of high quality steel. In order not to interfere with the flow the discs are chamfered around their periphery. When producing the flat pressure sensors for you we can take your individual design requests into account. Simply contact us for a nonbinding offer.

The sensor model 8228 with its measuring accuracy of 0.05% F.S. (for the measuring ranges ≤ 1 bar, the measuring accuracy is 0.1% F.S.) ideally suited as a reference sensor. The compact dimensions, the robust housing and the industrial-grade output signal result in a very wide range of applications. All components in contact with media are made of stainless steel. An integrated measuring amplifier converts the measuring signals directly into interference-free voltage signals or current signals that can be transmitted over long distances. With the „gage“ measurement type, the pressure measurement is carried out against the ambient pressure, the sensor has a bore that is protected against ambient influences to compensate for the ambient pressure. With the „Absolute“ measurement type, the applied pressure is measured against an enclosed vacuum; this measurement type is available from the measuring range 0 ... 250 mbar. The electrical connection is made via an M12 x 1 connector.

Monitoring tire geometry i.e. the measurement of radial or lateral unbalance as well as side wall detection for bulges, constrictions, dents etc., is one of the most important inspections at the end of the production process. The TGI 8302.LLT system can be easily integrated while offering precise measuring results.

The capaNCDT 6110 is a new, capacitive single-channel displacement measurement system comprising a compact controller, a sensor cable and the sensor. Due to the miniaturised controller and its easy operation, the capaNCDT 6110 is ideally suited to the integration in machines and facilities.

Pressure sensor for relative pressure measurement Robust housing for the use in harsh environments Suitable for relative pressure measurement Suitable for pressure measurement up to 600 bar Simple assembly Certified for shipbuilding and offshore industry by DNV-GL

Pressure sensor for relative pressure measurement Vacuum-proof Various process connections: G¼ B, ¼ - 18 NPT, M14 x 1.5 Measurement range: Min. 2 bar, max. 600 bar Electrical connections: Elbow connector Form A EN 175301-803, Circular connector Euro M 12 x 1, cable outlet 2 m length Certified for shipbuilding industry and offshore by DNV-GL

The DTA defines the industry standard in combination with temperature measurement. One process connection suffices to measure both values. The unit excels in its high quality workmanship and cost efficiency. Its absolute reproducibility and stable measuring values contribute to our measurement accuracies.

Pressure Transmitter with Integrated Amplifier and Integrated Temperature Measurement The DTAI first of all offers the user the comfort of operating a DAI in combination with temperature measurement. One process connection suffices in order to measure both values. These model offers mA and V output signals for further processing. The popular and most commonly used 2-wire and 4-20 mA configuration provide unequalled interference in critical environments. Liquid filled measuring system Maximum reliability through new membrane technology Standard G-coating to counteract adhesive materials Combined pressure and temperature measurement Robust design with G-Armor flexible components Applications with process medias of up to 400°C (750°F) possible Pressure ranges from 0-50 and 0-2.000 bar (0-725 to 29,000 psi) available Interference resistant signals over long distances Stable output signals

Melt Pressure Transducer with standardized output signal The DA Series melt pressure transducers are characterized by their high quality of workmanship and outstanding performance and are used in the plastic manufacturing and processing industries throughout the world. Their absolute reproducibility and stable measuring values contribute to our measurement accuracies. Application areas up to 300°C (572 °F) Pressure ranges from 0-50 and 0-2.000bar (0-725 and 29,000 psi) Liquid filled measuring system Maximum reliability through new membrane technology Standard G-coating to counteract adhesive materials 100% market compatible Mercury free version available at no additional surcharge

With the DAIX Series, Gneuss now has an explosion proof pressure transducer available. This melt pressure transducer is intrinsically safe. The uncompromising development of the DAIX provides an excellent choice for Ex-areas, complimenting years of tried and tested Gneuss products.

The DAIL fulfils the requirements of EN 1114-1 for overpressure protection of extrusion lines and offers maximum comfort of operation. The auto-zero function enables calibration directly on the device or from the observation point/controller. On the output side, the melt pressure transmitter provides a switch output in addition to the analog signal which enables switching off the machine in case of overpressure according to EN 13849-1, PL=c.

Melt Pressure Transducer with Integrated Amplifier The DAI Series offers – in addition to maximum reliability – improved user friendliness in the form of an Auto-Zero Function for local or remote configuration. These models offer mA and mV output signals for further processing. The popular and most commonly used 2-wire and 4-20mA configuration provide unequalled interference in critical environments.

The DAP Series incorporate a heated sensor tip, which limits the potential for sensor damage relating to the membrane, resulting from installation or removal of the pressure transmitter. The Gneuss patented heated sensor tip allows the sensor to be easily removed from a “frozen” melt without any problems. The diaphragm is not damaged when the polymer contracts. The DAP has revolutionized the handling of critical medias, for example PC, PMMA or ABS.

The F02 has been designed for application in systems which require a pressure transmitter with a Performance Level PL d or a Safety Integrity Level of SIL 2. It has a thin-film measurement cell made from stainless steel which is welded together with the pressure sensor and thus guarantees high media compatibility. It is available within pressures from 10 to 1200 bar. The output signal is made available at two outputs in parallel, whereby the second output represents an inverted signal. Users can select between a ratiometric and an 4-20-mA output in three-wire technology. The permitted media temperature range extends from -40…+125 °C. The total accuracy in the compensated range of 0…+80 °C lies at <= 1 % FS. The possible flexibility during integration into an existing machine is ensured through the provision of a multitude of available pressure connections as well as the small construction. The electrical contact takes place via a 5-pole M12 connector. The F02 also has E1 approval.

Pressure sensor for absolute pressure measurement. Vacuum-proof Various process connections: G¼ B, ¼ - 18 NPT, M14 x 1.5 Measurement range: Min. 1 bar, max. 25 bar Electrical connections: Elbow connector Form A EN 175301-803, Circular connector Euro M 12 x 1, cable outlet 2 m length Certified for shipbuilding industry and offshore by DNV-GL

The M01 series has been especially designed for applications in adverse ambient conditions in the same way value is placed on high resistance to aggressive media. Furthermore, the modular principle permits many combinations of pressure connection, pressure range, output signal and connector, so that the right sensor can be found for most applications. For pressure ranges from 10 to 2000 bar, which are frequently required for use on mobile machines, welded stainless steel measurement cells are used which are suitable for media temperatures from −40 to +150 °C. Depending on the type of measurement cell and the material coming into contact with the media, the M01 is resistant to aggressive/non-aggressive gases and liquids. On request, versions in 316L design for use in hydrogen pressure measurements are available. In addition to CE and UL certificates, every M01 product with a 1.4542 stainless steel measurement cell possesses an E1 approval verifying its suitability for use in vehicles.

Speed sensors from Lenord+Bauer are particularly suited for continuous operation in durable capital goods thanks to the magnetic sensing principle. They detect rotational and linear motion. The sensors are protected against extreme weather conditions, humidity, shock, and vibration due to an encapsulation process and specially developed production methods. Thus they are in compliance with DIN EN 50155 and meet the requirements of protection class up to IP 68. Customised versions by adapting the housing, or different cable and plug fabrication, Lenord+Bauer can implement almost any installation position. Depending on requirement, the sensors generate single or multichannel squarewave signals alternatively as voltage or current signal ranging from 0 to 25 kHz. A standstill signal can also be implemented. On request ATEXprotected product variants, special output signals for functional testing, and sensors with integrated pulse division or pulse multiplication are available.