Connecting pins - Import export

The troubleshooter for energy supply systems in the chip area - available in 4 sizes. Chips and dirt can affect the service life of cables and hoses significantly. With the RX system, igus® offers an extremely tight plastic e-tube that is nonetheless very easy to open. Snap-open in the outer radius A smooth, curved outer contour prevents chips from sticking Injection-molded "sealing lips" all around No holes, cracks, undercuts Series RX40 is IP40 tested (TÜV Saarland) Interior separation and guide trough available Covered pin/hole connection and stops "RBR" version with bending radius on both sides available Typical branches of industry Machine tools All applications in the direct chip sector Applications exposed to dust and dirt General mechanical engineering Dimensions and technical datas RX e-tubes RX32 Inner height hi: 42 mm Inner widths Bi: 80mm Bending radii R: 80 - 250 mm Pitch: 32 mm RX E-Tube RX40 Inner height hi: 52 mm Inner widths Bi: 100 mm bending radii R: 100 - 300 mm Pitch: 40 mm RX E-Tube RX48 Inner height hi: 62 mm Inner widths Bi: 120mm Bending radii R: 120 - 325 mm Pitch: 48 mm RX E-Tube RX56 Inner height hi: 73 mm Inner widths Bi: 140mm Bending radii R: 140 - 350 mm Pitch: 56 mm RX E-Tube RX56 High-temperature plastic version of the chip-proof RX energy tubes from stock - 850°C from 24h RX - from stock against hot chips red dot 2011: honourable mention for RX40 iF-Design-Award for RX e-tubes ESD classification: Electrically conductive ESD/Atex versions on request UL94-V0 classification on request e-tubes available as special design with HT material for 850°C hot chips The troubleshooter for energy supply systems in the chip area - available in 4 sizes. Chips and dirt can affect the service life of cables and hoses significantly. With the RX system, igus® offers an extremely tight plastic e-tube that is nonetheless very easy to open. Snap-open in the outer radius A smooth, curved outer contour prevents chips from sticking Injection-molded "sealing lips" all around No holes, cracks, undercuts Series RX40 is IP40 tested (TÜV Saarland) Interior separation and guide trough available Covered pin/hole connection and stops "RBR" version with bending radius on both sides available Typical branches of industry Machine tools All applications in the direct chip sector Applications exposed to dust and dirt General mechanical engineering Dimensions and technical datas RX e-tubes Chip tests in the igus® laboratory demonstrate the tremendous chip-proof properties of the igus® RX tube. Chip-proof - for all types of chips and applications RX32 Inner height hi: 42 mm Inner widths Bi: 80mm Bending radii R: 80 - 250 mm Pitch: 32 mm RX E-Tube RX40 Inner height hi: 52 mm Inner widths Bi: 100 mm bending radii R: 100 - 300 mm Pitch: 40 mm RX E-Tube RX48 Inner height hi: 62 mm Inner widths Bi: 120mm Bending radii R: 120 - 325 mm Pitch: 48 mm RX E-Tube RX56 Inner height hi: 73 mm Inner widths Bi: 140mm Bending radii R: 140 - 350 mm Pitch: 56 mm RX E-Tube RX56 High-temperature plastic version of the chip-proof RX energy tubes from stock - 850°C from 24h RX - from stock against hot chips Submersion test in water - Various tube types were submerged under water. The new RX tube needs over 30 seconds until it is filled up, thus proving its high leak tightness Y = time in seconds A = igus® products B = competitor Chip penetration test - Various types of tube were exposed to a defined quantity of chips. In the new RX tube, after 80,000 cycles only 0.2 g of chips were found in the interior Y = chip mass [g] A = igus® RX e-tube RX40.100.100 251.900 cycles B = igus® e-tubes 68.10.100.0 256.132 cycles C = test tube 01 250.907 cycles D = test tube 02* 2.600 cycles *Teststop after 2.600 cycles E = igus® products F = competitor E-Chain® selection aids You can find the right E-Chain® quickly by entering concrete parameters and with the aid of a comparison table. Productfinder Assembly instruction Dismantling / assembling a cover, replacing a chain link and assembling / inserting the RX tube. Assembly instruction Configure interior separation Define cables, select chain and configure interior separation. Now also for RX tubes! Interior separation configurator Application examples Applications in various industrial sectors. RX tubes Series RX - new chip-proof design, small pitch, removable cover 1 Chip-proof design without undercuts and edges 2 Excentric locking 3 Material igumid G 4 rounded shape 5 covered pin/hole connection RX tubes IP tested Technical report TÜV NORD red dot 2011: honourable mention for RX40 iF-Design-Award for RX e-tubes ESD classification: Electrically conductive ESD/Atex versions on request UL94-V0 classification on request e-tubes available as special design with HT material for 850°C hot chips

The T3 system combines smooth operation, low noise, simple assembly, and economy. The side bands, which snap together, replace a conventional pin and bore connection and prevent relative movements between the joints giving extremely low wear. This means virtually no wear or abrasion (cleanroom). The t-band's geometry means that hardly any polygon effect is generated when the energy chain is placed. The t-band therefore rolls in a very smooth arc, giving extremely low vibration and noise. In order to reduce the manufacturing and installation costs, the t-band is not mounted individually, but – much like the E3 system – in an eight-link length. Due to its low mass, the t-band is suitable for applications with low fill weights and short strokes combined with high speeds and accelerations.

RST20i3 device connection, standard, straight, M25, 3-pin, socket version, connection type spring-loaded connection, rated voltage 250 V, rated current 20 A, coding color / contact insert black

The new strain gage amplifier with IO-Link interface enables digitalization of the measurement technology right from the sensor. Its compact design and high degree of protection allow the instrumentation amplifier to be used practically anywhere in the field. Strain gage sensors typically have an output voltage of a few millivolts. In industrial environments, e.g. in the vicinity of electric motors or frequency converters, interference can affect the measurement result when transmitting analog signals. This is reliably avoided using the new strain gage amplifier with IO-Link interface. The analog link between the sensor and instrumentation amplifier is kept as short as possible, the standardized IO-Link communication is fully digital and interference-free. The amplifier is powered directly via the IO-Link interface – a standardized 5-wire cable with M12 socket. Strain gage sensors can be connected via a 4-pin M8 connector.

Use: Connector for thermocouple and RTD circuits. The solid connector pins guarantee reliable connection under even the most difficult conditions. The third contact for ground or continuous shield or for three wire RTD´s. Mechanical design: • Housing of fibreglass-filled plastic. • Contacts of original thermocouple materials. • Solid connector pins and spring-loaded socket. • Reverse polarity protection by different pin thicknesses. • Central cover attachment for fast installation. • Moulded barriers prevent short-circuits. • Screw terminals enable quick connection.

Use: Connector for thermocouple and RTD circuits. The solid connector pins guarantee reliable connection under even the most difficult conditions. Jab-in cover allow easy connection without need cover removal. Mechanical design: • Housing of fibreglass-filled plastic. • Contacts of original thermocouple materials. • Reverse polarity protection by different pin thicknesses. • Central cover attachment for fast installation. • Moulded barriers prevent short-circuits. • Screw terminals enable quick connection.

Use: Plug connector for thermocouple and RTD circuits. The solid connector pins guarantee reliable connection under even the most difficult conditions. Mechanical design: • Housing of fibreglass-filled plastic. • Contacts of original thermocouple materials. • Solid connector pins and spring-loaded socket. • Reverse polarity protection by different pin thicknesses. • Central cover attachment for fast installation. • Moulded barriers prevent short-circuits. • Screw terminals enable quick connection.

Use: Plug connector for thermocouple and RTD circuits. The solid connector pins guarantee reliable connection under even the most difficult conditions. Mechanical design: • Housing of fibreglass-filled plastic. • Contacts of original thermocouple materials. • Solid connector pins and spring-loaded socket. • Reverse polarity protection by different pin thicknesses. • Central cover attachment for fast installation. • Moulded barriers prevent short-circuits. • Screw terminals enable quick connection.

Use: Plug connector for thermocouple and RTD circuits. The solid connector pins guarantee reliable connection under even the most difficult conditions. Mechanical design: • Housing of fibreglass-filled plastic. • Contacts of original thermocouple materials. • Solid connector pins and spring-loaded socket. • Reverse polarity protection by different pin thicknesses. • Central cover attachment for fast installation. • Moulded barriers prevent short-circuits. • Screw terminals enable quick connection.

The MBS hydraulic cylinders of the MZR-1007 series are synchronized cylinders with pivot pins for robust, high-frequency use in general mechanical engineering. The cylinder is connected via a pivot pin ring, which can be variably screwed to the cylinder tube, and a threaded neck on the piston rod, which is designed for rod ends according to DIN24338 / ISO6982. There are also connection bores for pipe connections according to BSPP ISO 1179-2. Hub and piston rod overhang are variably selectable. With the exception of the piston rod, all surfaces are protected against corrosion with a black primer. On request alternative surface treatments are possible. The surface of the piston rod is hard chromed, ground and polished. The cylinders are suitable for hydraulic fluids of types H, HL and HLP according to DIN 51524/51525. If you have questions about areas of application or other options, we are happy to answer them. Download the data sheet for detailed information

With its rugged housing and a stainless steel sensor element, the transducer is particularly robust and ideally suited to the harshest environments. This also means that the sensor can be installed anywhere with no effect on the measurement signal. The built-in instrumentation amplifier converts the sensor signals into noise-immune voltage signals or current signals that can be transmitted over relatively long distances. For high viscose materials, a front-level membrane M12 x 1 is available, and with this disruptive dead volumes can be expelled. The sensor has a small protected hole on the rear to allow measurement of atmospheric pressure (measurement type relative). For the absolute measurement option, the applied pressure is measured with respect to an enclosed vacuum. As an electrical connection, a DIN 43650A valve connector or an M12 x 1, 4-pin connection is available.

The new generation of our VH series valve terminals. Modern pneumatics with economical energy consumption, compact dimensions and high flow rates. With multipolar electrical connection with D-SUB 25-pin or flat connector as standard. Core items: Reduced dimensions (15mm) Low power consumption (0.85W) High flow rate for size Compact and clear design Metal construction for a long service life even under harsh environmental conditions Fast cycle times thanks to the latest generation of magnetic coils Manual operation easily accessible LED display integrated in the magnetic coil Connection strips with modular system All islands are delivered assembled and tested

▪ Analogue version ▪ 5-pin connection ▪ Can be used with all analogue Hydraulic Testers of the PPC series ▪ CAN version ▪ 5-pin SPEEDCON connection plug ▪ Housing: Aluminium (black anodised) ▪ Gaskets: FPM (Viton®) ▪ Accuracy (at 21 cSt): ±1 (% FS*) or ±1 (% of the displayed value) ▪ Pressure measurement connection: SMK20 (M16 x 2) ▪ Temperature measurement connection: M10 x 1 (standard screw plug) ▪ Calibration certificate on request ▪ UNF version on request Ambient Conditions ▪ Media temperature: -20 °C ... +90 °C / -4 °F ... +194 °F ▪ Ambient temperature: -10 °C ... +50 °C / +14 °F ... +122 °F ▪ Storage temperature: -20 °C ... +80 °C / -4 °F ... +176 °F ▪ Permissible particle size: < 10 Micron for SFM-015 < 25 Micron for others ▪ Viscosity range: 10 ... 100 cSt Electrical Data ▪ Response time: 50 ms ▪ Flow Turbine (analogue): A PPC-04/12-CAB3 (3 m / 9.84 ft) Connection Cable is needed to connect the sensor to the current Hydraulic Testers. A PPC-04/12-CAB5-EXT (5 m / 16.40...

▪ Screw-in version, measures current temperatures directly in the pipeline ▪ Rod-type version (-TSH), especially designed to determine the media temperatures in tanks and containers ▪ 5-pin connection ▪ Input signal: 0 ...3 V DC ▪ Output signal: 7 ...12 V DC ▪ CAN version ▪ Indication of the sensor status via LED ▪ 5-pin SPEEDCON connection plug ▪ CANopen protocol profile DS301, Typ 2.0A with manufacturer-specific additions ▪ LSS service DS305 v2.0 ▪ Output signal: CAN bus ▪ Measurement medium: liquids (consult STAUFF for use with aggressive media ▪ Calibration certificate on request Materials ▪ Housing (T): Stainless Steel ▪ Gaskets (T): FPM (Viton®) ▪ Rod (TSH): Stainless Steel 1.4304 ▪ Handle (TSH): Delrin Weight ▪ T (M10x1): 70 g / .15 lbs ▪ T (G1/4): 55 g / .12 lbs ▪ TSH: 120 g / .26 lbs Connection: ▪ a) STAUFF Test connection SGV-16S-G-C6F in the pipeline (only M10x1) ▪ b) Screw-in thread (T): M10 x 1 or G1/4 ▪ c) Screw-in thread (TSH): M10 Ambient Conditions (Screw-in...

The PPC-04/12-SDS-CAB Rotational Speed Sensor allows non-contact speed measurement of rotating components. The sensor is based on a opto-electrical measurement principle that determines the rotational speed with high-accuracy using a reflecting strip on the shaft. The contact rotational speed measurement is obtained by using a Contact Adaptor that is mounted to the sensor, and which makes contact with the rotating component during measurement. This also produces high-accuracy measurement results. In the case of espacially small areas, using the focusing adaptor facilities measurement. ▪ 5-pin connection ▪ Both contacting and non-contacting measurement possible ▪ Type of measurement: optical, red LED ▪ Calibration certificate on request Material ▪ ABS Weight ▪ 230 g / .51 lbs Measuring Range ▪ Measuring range: 20 ... 10000 1/min ▪ Measuring distance: 25 ... 500 mm (1 ... 20 in) ▪ Measuring angle: ±45 °C ▪ Accuracy: ≤ ±0,5 % FS* ▪ Resolution: ±5 1/min Electrical Data ▪ Output...

▪ Analogue version ▪ 5-pin connection ▪ Can be used with all analogue Hydraulic Testers of the PPC series ▪ Input voltage: 9 ... 36 V DC ▪ Output signal: 0 ... 3 V DC ▪ CAN version ▪ Indication of the sensor status via LED ▪ 5-pin SPEEDCON connection plug ▪ CANopen protocol profile DS406 v3.2 with manufacturer-specific additions ▪ LSS service DS305 v2.0 ▪ Sturdy Stainless Steel housing (1.4301) ▪ FPM (Viton®) gasket ▪ Weight: 85 g / .19 lbs ▪ Suitable for gases and liquids (in the case of aggressive media, only after consultation) ▪ Accuracy (±0,25% FS* typ.) ▪ Automatic sensor recognition ▪ Process Connection G1/4 (without adaptor) ▪ Calibration certificate on request Ambient Conditions ▪ Media temperature: -25 °C ... +105 °C /-13 °F ... +221 °F ▪ Ambient temperature: -25 °C ... +85 °C / -13 °F ... +185 °F ▪ Storage temperature: -25 °C ... +85 °C / -13 °F ... +185 °F ▪ Load cycles (10 6): 100 Electrical Data ▪ Response time: 1 ms ▪ Long-term stability: < 0,2 % FS* /a ▪ Vibration...

▪ Analogue version ▪ 5-pin connection ▪ Can be used with all analogue Hydraulic Testers of the PPC series ▪ Input voltage: 7 ... 12 V DC ▪ Output signal: 0 ... 3 V DC ▪ CAN version ▪ Indication of the sensor status via LED ▪ 5-pin SPEEDCON connection plug ▪ CANopen protocol profile DS406 v3.2 with manufacturer-specific additions ▪ LSS service DS305 v2.0 ▪ Sturdy Stainless Steel housing (1.4301) ▪ FPM (Viton®) gasket ▪ Weight: 200 g / .44 lbs ▪ Suitable for gases and liquids (in the case of aggressive media, only after consultation) ▪ Accuracy (±0,25% FS* typ.) ▪ Automatic sensor recognition ▪ Pressure connection G1/2 (without adaptor) ▪ Calibration certificate on request Ambient Conditions ▪ Media temperature: -25 °C ... +105 °C /-13 °F ... +221 °F ▪ Ambient temperature: -25 °C ... +85 °C / -13 °F ... +185 °F ▪ Storage temperature: -25 °C ... +85 °C / -13 °F ... +185 °F ▪ Compensated range: 0 °C ... +85 °C / +32 °F ... +285 °F ▪ Load cycles (10 6): 100 Electrical Data ▪ Response...

Spindle extension consisting of a rigid, hot-dip galvanized key rod and a separate, rigid PE protection tube. Square bars 13 × 13 mm, hot-dip galvanized. Operating square suitable for operating key DIN 3223 E (House connection fittings). Connecting pins in stainless steel v2a. Coupling sleeve made of iron GGG40, galvanised, with slot and VA-Clip-pin (tool-free connection system). PE-HÜLSROHR with centering cap and universal-level bell, dirt-proof and water-repellent

Spindle extension consisting of a two-piece, hot-dip galvanised steel rod and a separate, adjustable PE protection tube. Rod continuously adjustable with Auszugsicherung and self-supporting in each statement positions. Locking of the set minimum length by a v2a-collar with VA-threaded pin M10. Operating square forged, 12/14 mm, suitable for operating key DIN 3223 E (House connection fittings). Connecting pins in stainless steel v2a. Coupling sleeve made of iron GGG40, galvanised, with slot and VA-Clip-pin (tool-free connection system). PE-HÜLSROHR with centering cap and universal-level bell, dirt-proof and water-repellent.

Telescopic spindle extension consisting of a two-piece, hot-dip galvanized steel rod and a verstifteten PE protection tube. steplessly adjustable with Auszugsicherung and self-supporting in each statement positions. Operating square forged, 12/14 mm, suitable for operating key DIN 3223 E (House connection fittings). Dome sleeve made of iron GGG40, galvanised. Connecting pins in stainless steel v2a. Coupling sleeve with slot and VA-Clip-pin (tool-free connection system). PE-HÜLSROHR with centering cap and universal-level bell, dirt-proof and water-repellent. Optional: Marking disc, usable on both sides, e.g. for gas or water.

A two-piece stainless steel rod (1.4301), coupling (bottom adapter) for spindle and shaft and square cap (accord. to DIN3223 C or E) made of stainless steel AISI 304. Toolles assembly of the spindle extension with a stainless steel clip-pin. Connection pins made of stainless steel 1.4301. Transport security of the rod minimum of 150N. Self-locking in every adjustable position with a PE sealing collar on the steel tube. Torques up to 1000Nm (oval type wedge gate valve with square tube size 30mm). Three-piece PE protection tube system with an additional corrugated protection tube, bonded centring cap and either a universal combi bell (Form C) or a universal bell (size Ø80mm or Ø100mm (Form E)). Completely dirt-proof and water-repellent. Incl.: Marking disc (double sided gas and water) as well as a universal bell adapter/sealing insert.

A two-piece hot-dip galvanised steel rod accord. to DIN EN 10240 (alternatively in stainless steel), coupling (bottom adapter) made of GJS400-15, galvanised accord. to DIN EN 12329 und DIN 50961 (alternatively made of stainless steel AISI 304). Square cap (top adapter) (accord. to DIN 3223 E) made of GJS400-15, galvanised accord. to DIN EN 12329 and DIN 50961 (alternatively in stainless steel AISI 304). Toolless assembly of the spindle extension with a stainless steel clip pin. Connection pins made of stainless steel 1.4301. Transport security of the rod minimum of 150N. Self-locking in every adjustable position through a PE sealing collar on the steel tube. Torques up to 140Nm. Three-piece PE protection tube system with a bonded centring cap, universal combi bell and sealing. Completely dirt-proof and water-repellent. Incl.: Marking disc (double sided gas and water) as well as a universal bell adapter.

A three-piece rod made of stainless steel 1.4301, coupling (bottom adapter) precision casting, galvanised accord. to DIN EN 12329 und DIN 50961 (alternatively made of stainless steel AISI 304), square cap (top adapter) (accord. to DIN 3223 E) made of GJS400-15, galvanised accord. to DIN EN 12329 and DIN 50961 (alternatively in stainless steel AISI 304). Toolless assembly of the spindle extension with a stainless steel clip pin. Connection pins made of stainless steel 1.4301. Transport security of the rod minimum of 150N. Self-locking in every adjustable position through a PE sealing collar on the steel tube. Torques up to 250Nm. Four-piece PE protection tube system with a bonded centring cap, universal combi bell with sealing/sealing insert and a grooved and suspension system as rotation lock. Completely dirt-proof and water-repellent. Incl.: Marking disc (double sided gas and water) as well as a universal bell adapter.

Telescopic spindle extension GW336 with standardised intersection accord. to worksheet DVGW336-1 (A), Edition September 2010. DVGW tested accord. to technical examination basis DVGW 336-2 (P). Two-piece hot-dip galvanised steel rod accord. to DIN 10240 (alternatively in stainless steel), without coupling (bottom adapter), with connection drilling, square cap (top adapter) (accord. to DIN 3223 E) made of GJS400-15, galvanised accord. to DIN EN 12329 and DIN 50961 (alternatively in stainless steel AISI 304). Connection pins made of stainless steel 1.4301. Transport security of the rod minimum of 150N. Self-locking in every adjustable position through a PE sealing collar on the steel tube. Torques accord. to GW336-2 (P). Three-piece PE protection tube system with a bonded centring cap and bell accord. to GW336-1 (A). Completely dirt-proof and water-repellent. Incl.: Marking disc (double sided gas and water) as well as a universal bell adapter.

Telescopic spindle extension GW336 with standardised intersection accord. to worksheet DVGW336-1 (A), Edition September 2010. DVGW tested accord. to technical examination basis DVGW 336-2 (P). Two-piece hot dip galvanised steel rod accord. to DIN 10240 (alternatively in stainless steel), without coupling (bottom adapter), with connection drilling, square cap (top adapter) (accord. to DIN 3223 E) made of GJS400-15, galvanised accord. to DIN EN 12329 and DIN 50961 (alternatively in stainless steel AISI 304). Connection pins made of stainless steel 1.4301. Transport security of the rod minimum of 150N. Self-locking in every adjustable position through a PE sealing collar on the steel tube. Torques accord. to GW336-2 (P). Three-piece PE protection tube system with a bonded centring cap and bell accord. to GW336-1 (A). Completely dirt-proof and water-repellent. Incl.: Marking disc (double sided gas and water) as well as a universal bell adapter.

Telescopic Spindle Extension T3 with screw bell. A two-piece hot-dip galvanised steel rod accord. to DIN EN 10240 (alternatively in stainless steel), coupling (bottom adapter) made of GJS400-15, galvanised accord. to DIN EN 12329, square cap (top adapter) made of GJS400-15, galvanised accord. to DIN EN 12329 and DIN 50961 (alternatively in stainless steel AISI 304). Suitable for operating key DIN 3223 C or E. Toolles assembly of the spindle extension with a stainless steel clip pin. Connection pins made of stainless steel 1.4301. Transport security of the rod minimum of 150 N. Self-locking in every adjustable position through a PE sealing collar on the steel tube. Torques accord. to GW336. Three-piece PE protection tube system with an additional corrugated protection tube, bonded centring cap and screw bell. Completely dirt-proof and water-repellent.

Telescopic Spindle Extension T3 - waterproof. A two-piece hot-dip galvanised steel rod accord. to DIN EN 10240 (alternatively in stainless steel), coupling (bottom adapter) made of GJS400-15, galvanised accord. to DIN EN 12329, square cap (top adapter) made of GJS400-15, galvanised accord. to DIN EN 12329 and DIN 50961 (alternatively in stainless steel AISI 304). Suitable for operating key DIN 3223 C. Toolles assembly of the spindle extension with a stainless steel clip pin. Connection pins made of stainless steel 1.4301. Transport security of the rod minimum of 150 N. Self-locking in every adjustable position through a PE sealing collar on the steel tube. Torques accord. to GW336. Three-piece PE protection tube system with an additional corrugated protection tube, bonded centring cap and flange bell (F10). Completely dirt-proof and water-repellent.

Telescopic Spindle Extension T3 for ball valves with polygon. A two-piece hot-dip galvanised steel rod accord. to DIN EN 10240 (alternatively in stainless steel), square cap (top adapter) made of GJS400-15, galvanised accord. to DIN EN 12329 and DIN 50961 (alternatively in stainless steel AISI 304) with connection drillings accord. to GW336. Suitable for operating key DIN 3223 C or E (DN25-50). Toolles assembly of the spindle extension with a stainless steel clip pin. Connection pins made of stainless steel 1.4301. Transport security of the rod minimum of 150N. Self-locking in every adjustable position through a PE sealing collar on the steel tube. Torques accord. to GW336. Three-piece PE protection tube system with an additional corrugated protection tube, bonded centring cap and universal round bell accord. to GW336. Completely dirt-proof and water-repellent. Incl.: Integrated position indicator „1/4 turns“.

Telescopic Spindle Extension T3 for ball valves with square connection. A two-piece hot-dip galvanised steel rod accord. to DIN EN 10240 (alternatively in stainless steel), square cap (top adapter) made of GJS400-15, galvanised accord. to DIN EN 12329 and DIN 50961 (alternatively in stainless steel AISI 304) with connection drillings accord. to GW336. Suitable for operating key DIN 3223 C or E (DN25-50). Toolles assembly of the spindle extension with a stainless steel clip-pin. Connection pins made of stainless steel 1.4301. Transport security of the rod minimum of 150N. Self-locking in every adjustable position with a PE sealing collar on the steel tube. Torques accord. to GW336. Three-piece PE protection tube system with an additional corrugated protection tube, bonded centring cap and universal round bell accord. to GW336. Completely dirt-proof and water-repellent. Incl.: Integrated position indicator „1/4 turns“.