Squares - Import export

Square cartridge heaters are used where much power has to be installed near the surface of a tool, e.g. in cutting knives, sealing stations or hot plates. With a soft, malleable condition in stainless steel or nickel sheath square cartridge heaters can easily be pressed into common milled rectangular grooves. Apart from the advantageous heat transfer over ¾ of the sheath, it is not necessary to cement or cast in the heater which is imperative for round cartridge heaters. Unlike tubular heaters which are also available in square sections (see chapter Flexible Heating Pipes), the square cartridge heaters have the termination on one side and can be loaded with 16W/cm² (2.5W/in²) due to their special inside construction.

Height-adjustable floor socket 8901B with one slot. The housing is made of sendzimir galvanized sheet steel, the frame and lid are made of stainless steel. Floor coverings such as carpet, parquet, laminate etc. with a thickness of 15 mm can be used in the removable hinged lid. The lid closes even when the standard plugs are inserted in straight or angled form. Further equipment variants on request

drylin® Q Square linear guides Square section tube made of hard-anodized aluminum Torque resistant without 2nd guidance Tolerates moments up to 10 Nm drylin® Q square section tube drylin® Q - bearing housing, adjustable Carriage version for all unsupported solutions Force absorption from all directions Anti-rotation Clearance is continuously adjustable manually drylin® Q - bearing housing drylin® Q - bearing housing, adjustable with hand clamp Carriage version for all unsupported solutions Force absorption from all directions Anti-rotation Clearance is continuously adjustable manually With manual clamp drylin® Q - bearing housing with manual clamp drylin® Q - housing bearing Q20 enclosed, anodized aluminium housing short design or tandem housing Torque resistant without 2nd guidance drylin® housing bearing Q20 drylin® W - flange bearing Flange pillow block made of anodized aluminum Round flange (01 version), square flange (02 version Standard type or tandem housing Torque resistant without 2nd guidance drylin® W - flange bearing drylin® Q - housing bearing Q10 Solid polymer bearing made of iglidur® J Very light Tolerates moments up to 3 Nm Space saving drylin® Q - housing bearing Q10 drylin® Q - accessory Based on a torque resistant square guide with 7.5 mm edge lengths Hollow chamber for supply lines (media, compressed air,cable) drylin® Q - accessory drylin® Q - gripper axis Toothed, hard-coated and corrosion protected square-hollow profile Move loads up to 500 g at speeds of up to 0.7 m/s Bearing made of iglidur® J Drive: NEMA11 stepper motor with gear wheel drylin® Q - gripper axis Move linear torque resistant, completely lubrication-free. The drylin® Q linear construction kit offers the user maximum flexibility in the design Individual housing options such as solid plastic bearings and adjustable complete housings with and without manual clamp are available. Due to the hollow chamber design, the rugged hard-anodised aluminium profile is very light and is suitable for the simultaneous conducting of supply cables. The mounting options are highly variable, among others, using slot nuts; installation size 20 can also combined with all 20/20 aluminium construction profiles. 1. Profile made of hard-anodized aluminum 2. Main body of the carriage made of aluminum 3. Customized clearance adjustment 4. Cover made of solid plastic 5. Gliding elements in high-performance polymer iglidur® J serve as a guide bearing and guarantee optimum running properties drylin® Q Square linear guides Square section tube made of hard-anodized aluminum Torque resistant without 2nd guidance Tolerates moments up to 10 Nm drylin® Q square section tube drylin® Q - bearing housing, adjustable Carriage version for all unsupported solutions Force absorption from all directions Anti-rotation Clearance is continuously adjustable manually drylin® Q - bearing housing drylin® Q - bearing housing, adjustable with hand clamp Carriage version for all unsupported solutions Force absorption from all directions Anti-rotation Clearance is continuously adjustable manually With manual clamp drylin® Q - bearing housing with manual clamp drylin® Q - housing bearing Q20 enclosed, anodized aluminium housing short design or tandem housing Torque resistant without 2nd guidance drylin® housing bearing Q20 drylin® W - flange bearing Flange pillow block made of anodized aluminum Round flange (01 version), square flange (02 version Standard type or tandem housing Torque resistant without 2nd guidance drylin® W - flange bearing drylin® Q - housing bearing Q10 Solid polymer bearing made of iglidur® J Very light Tolerates moments up to 3 Nm Space saving drylin® Q - housing bearing Q10 drylin® Q - accessory Based on a torque resistant square guide with 7.5 mm edge lengths Hollow chamber for supply lines (media, compressed air,cable) drylin® Q - accessory drylin® Q - gripper axis Toothed, hard-coated and corrosion protected square-hollow profile Move loads up to 500 g at speeds of up to 0.7 m/s Bearing made of iglidur® J Drive: NEMA11 stepper motor with gear wheel drylin® Q - gripper axis

Floor box 8808T with 8 slots made of polished stainless steel. It can be installed at any point in the floor, as pipes are used for the line feed. Because of its low height, this version is particularly suitable for floors in old buildings. The lid is designed for the inlay of carpets, cork floors or the like, with a covering thickness of 5–7 mm, and closes even when the plugs are inserted. Further equipment variants on request.

Square stainless steel tubular heaters BASE-flex (1.4541) are a reliable industry standard for the use in heating platens and manifolds. In contrast to traditional tubular heaters with a round section which have to be bent by machines, square BASE-flex can be fitted into any rectangular groove with simple hand tools. Moreover, the square shape results in a bigger heat emitting area of up to 80% compared with a corresponding round section. Finally, the easy manual mounting saves the usually high technical expenditure for casting-in / soldering / cementing of bent round tubular heaters. A soft version of the BASE-flex, the NICKEL-flex (2.4068) is available as special execution. Due to the soft, easy to form nickel material, the NICKEL-flex is suitable for manual mounting with hand tools in round sections, too. Furthermore, Nickel has a better capability to conduct heat compared with stainless steel.

plow bolt with square neck M16 in class 8.8, zinc plated

The CEE floor tank 6620A consists of a housing made of stainless steel 1.4301 (3 mm) and a 20 mm thick cover made of anodized aluminum that can be closed with a tool. When closed, the CEE floor tank is not waterproof. In the outdoor area, a drainage pipe must be provided on site for the housing to be drained. Due to the surface load of 6.5t, this version can be driven on with a truck if it is properly installed and the lid is completely closed. The lid opens with the help of a gas pressure spring and can be closed with plugged-in plugs. Other equipment variants on request.

The housing of the 2008Q floor box is made of 1.5 mm thick V2A stainless steel and has a lockable aluminum lid. The sturdy floor box is passable by car. With a lid seal it is suitable for cleaning with wet sweepers. Correct installation is a prerequisite. The device unit can contain up to 8 installation devices. The sockets have a VDE mark. With internal tube for using the tank with the lid closed. Further equipment variants on request.

Advantages of Heating Plates with Square Cartridge Heaters: -> Simple plate manufacture due to rectangular groove geometry, no deep-hole boring -> Simple heater installation by bending and pressing along the plate surface -> Complex plate geometries with bores and openings -> Optimal heat transfer due to 75% surface contact -> No casting with heat conductive compound -> Uniform temperature profiles due to thermally optimized groove layouts/power distribution and utilization of insulation plates -> high process temperatures (up to 450°C in aluminium, up to 700°C in stainless steel) Example "Heated Stamp": D=100 mm out of tempered tool steel up to max. 700°C continuous temperature. Fitted with 2 Square Cartridge Heaters 1500 W/ 230 V, 4,5 x 4,5 mm x 600 mm, with 50 mm unheated at the termination end. Annealed and formable with a nickel sheath, resistant up to 850°C surface temperature. Connection by fibreglass insulated pure nickel high-temperature leads (max. 500°C)

The square shopping basket made of solid willow is the perfect companion for the next big shopping tour. The two foldable handles lie well in the hand. The angular shape of the basket also fits well in the classic shopping trolleys and hardly takes up any space. The shop equipment in an organic market or farm shop is optimally rounded off with this filling basket in natural design. As a gift basket this article is a popular present.

countersunk head screw with square neck all sizes

mushroom head square neck bolts as per DIN 603 all sizes

Weight 5 kg Dimensions 18212724.7 cm

Weight 131 kg Dimensions .95-110251650 cm

Square Saver made of ductile and stainless steel casting

Floor Stand Central, closed, stored square tube

Telescopic Spindle Extension T3 for ball valves with square connection. A two-piece hot-dip galvanised steel rod accord. to DIN EN 10240 (alternatively in stainless steel), square cap (top adapter) made of GJS400-15, galvanised accord. to DIN EN 12329 and DIN 50961 (alternatively in stainless steel AISI 304) with connection drillings accord. to GW336. Suitable for operating key DIN 3223 C or E (DN25-50). Toolles assembly of the spindle extension with a stainless steel clip-pin. Connection pins made of stainless steel 1.4301. Transport security of the rod minimum of 150N. Self-locking in every adjustable position with a PE sealing collar on the steel tube. Torques accord. to GW336. Three-piece PE protection tube system with an additional corrugated protection tube, bonded centring cap and universal round bell accord. to GW336. Completely dirt-proof and water-repellent. Incl.: Integrated position indicator „1/4 turns“.

Spindle extension consisting of a rigid, hot-dip galvanized key rod and a separate, rigid PE protection tube. Square bars 13 × 13 mm, hot-dip galvanized. Operating square suitable for operating key DIN 3223 E (House connection fittings). Connecting pins in stainless steel v2a. Coupling sleeve made of iron GGG40, galvanised, with slot and VA-Clip-pin (tool-free connection system). PE-HÜLSROHR with centering cap and universal-level bell, dirt-proof and water-repellent

Dimensions Vkt. 6 - 300 mm 6 m / 12 m Grades S355J2+AR/+M/ +N C45 C60

As a danger protection, for separation and blocking of roads and walkways etc. Blocking of grassed areas and protection of trees, flower beds or as a safety guard in red and white warning colors. Additional powder coating in RAL and DB colors. Access barriers made of round tube Ø 60mm or square pipe 70 x 70mm, available in stationary, removable with triangular locking mechanism and revolving

Baking frame, adjustable • for baking, layering and decorating • made of stainless steel, fruit acid-resistant • extra high 80 mm • adjustable from 155 to 280 mm • fix selected size with the clips – hassle-free

Black Powder Coated Steel Housing and Pull, with Rubber Sleeve.Size:155.6*82.8mm.Maximum static load: 1610N.Easy Installation,ROHS compliance.

• cutting technology for the most discerning • non-slip foot for safe hold on the work-top • practical blade protector

Shape: square tube Material: EN AW-6060 (AlMgSi0,5), 3.3206 Condition: solution annealed, artificially aged Type of production: pressed Surface finish: anodised Standard: EN 755 eClass 9.1: 35020190 UNSPSC 11.2: 30102306 Dimensions: Thickness (mm): 2 - 3 Length (mm): 6,000 Edge length (mm): 25 - 30 RAL colour: E6 anodize EV1

Shape: square tube Material: EN AW-6060 (AlMgSi0,5), 3.3206 Condition: solution annealed, artificially aged Type of production: pressed Surface finish: Mill-finish Standard: EN 755 eClass 9.1: 35020190 UNSPSC 11.2: 30102306 Dimensions: Thickness (mm): 1.5 - 5 Length (mm): 6,000 Edge length (mm): 15 - 150

Shape: Square tube, round edged Material: EN AW-6060 (AlMgSi0,5), 3.3206 Type of production: pressed Condition: solution annealed, artificially aged Surface finish: mill-finish Standard: EN 755 eClass 9.1: 35020190 UNSPSC 11.2: 30102306 Dimensions: Thickness (mm): 2 - 4 Length (mm): 6,000 Edge length (mm): 30 - 80 Radius (mm): 2 - 6

Shape: square perforated sheet material: EN AW-1050 (Al99,5), 3.0255 Type of manufacture: rolled Condition: work-hardened, re-annealed, 1/2 hard Surface finish: mill-finish Standard: EN 573/EN 485 eClass 9.1: 35020503 UNSPSC 11.2: 30102506 Dimensions: Thickness (mm): 2 Length (mm): 2,000 Width (mm): 1,000 Hole size: 10 Pitch (hole center measured): 15

Shape: Square Material: EN AW-6060 (AlMgSi0,5), 3.3206 Type of production: pressed Condition: solution annealed, artificially aged Surface finish: Mill-finish Standard: EN 573/EN 485 eClass 9.1: 35020303 UNSPSC 11.2: 30102406 Dimensions: Edge length (mm): 8 - 60 Length (mm): 6,000

Shape: Square Material: EN AW-2007 (AlCuMgPb), 3.1645 Type of manufacture: drawn Condition: T3 acc. to EN 515 Standard: EN 573/EN 485 eClass 9.1: 35020303 UNSPSC 11.2: 30102406 Dimensions: Edge length (mm): 15 Length (mm): 3,000