Squares - Import export

Square cartridge heaters are used where much power has to be installed near the surface of a tool, e.g. in cutting knives, sealing stations or hot plates. With a soft, malleable condition in stainless steel or nickel sheath square cartridge heaters can easily be pressed into common milled rectangular grooves. Apart from the advantageous heat transfer over ¾ of the sheath, it is not necessary to cement or cast in the heater which is imperative for round cartridge heaters. Unlike tubular heaters which are also available in square sections (see chapter Flexible Heating Pipes), the square cartridge heaters have the termination on one side and can be loaded with 16W/cm² (2.5W/in²) due to their special inside construction.

Height-adjustable floor socket 8901B with one slot. The housing is made of sendzimir galvanized sheet steel, the frame and lid are made of stainless steel. Floor coverings such as carpet, parquet, laminate etc. with a thickness of 15 mm can be used in the removable hinged lid. The lid closes even when the standard plugs are inserted in straight or angled form. Further equipment variants on request

drylin® Q Square linear guides Square section tube made of hard-anodized aluminum Torque resistant without 2nd guidance Tolerates moments up to 10 Nm drylin® Q square section tube drylin® Q - bearing housing, adjustable Carriage version for all unsupported solutions Force absorption from all directions Anti-rotation Clearance is continuously adjustable manually drylin® Q - bearing housing drylin® Q - bearing housing, adjustable with hand clamp Carriage version for all unsupported solutions Force absorption from all directions Anti-rotation Clearance is continuously adjustable manually With manual clamp drylin® Q - bearing housing with manual clamp drylin® Q - housing bearing Q20 enclosed, anodized aluminium housing short design or tandem housing Torque resistant without 2nd guidance drylin® housing bearing Q20 drylin® W - flange bearing Flange pillow block made of anodized aluminum Round flange (01 version), square flange (02 version Standard type or tandem housing Torque resistant without 2nd guidance drylin® W - flange bearing drylin® Q - housing bearing Q10 Solid polymer bearing made of iglidur® J Very light Tolerates moments up to 3 Nm Space saving drylin® Q - housing bearing Q10 drylin® Q - accessory Based on a torque resistant square guide with 7.5 mm edge lengths Hollow chamber for supply lines (media, compressed air,cable) drylin® Q - accessory drylin® Q - gripper axis Toothed, hard-coated and corrosion protected square-hollow profile Move loads up to 500 g at speeds of up to 0.7 m/s Bearing made of iglidur® J Drive: NEMA11 stepper motor with gear wheel drylin® Q - gripper axis Move linear torque resistant, completely lubrication-free. The drylin® Q linear construction kit offers the user maximum flexibility in the design Individual housing options such as solid plastic bearings and adjustable complete housings with and without manual clamp are available. Due to the hollow chamber design, the rugged hard-anodised aluminium profile is very light and is suitable for the simultaneous conducting of supply cables. The mounting options are highly variable, among others, using slot nuts; installation size 20 can also combined with all 20/20 aluminium construction profiles. 1. Profile made of hard-anodized aluminum 2. Main body of the carriage made of aluminum 3. Customized clearance adjustment 4. Cover made of solid plastic 5. Gliding elements in high-performance polymer iglidur® J serve as a guide bearing and guarantee optimum running properties drylin® Q Square linear guides Square section tube made of hard-anodized aluminum Torque resistant without 2nd guidance Tolerates moments up to 10 Nm drylin® Q square section tube drylin® Q - bearing housing, adjustable Carriage version for all unsupported solutions Force absorption from all directions Anti-rotation Clearance is continuously adjustable manually drylin® Q - bearing housing drylin® Q - bearing housing, adjustable with hand clamp Carriage version for all unsupported solutions Force absorption from all directions Anti-rotation Clearance is continuously adjustable manually With manual clamp drylin® Q - bearing housing with manual clamp drylin® Q - housing bearing Q20 enclosed, anodized aluminium housing short design or tandem housing Torque resistant without 2nd guidance drylin® housing bearing Q20 drylin® W - flange bearing Flange pillow block made of anodized aluminum Round flange (01 version), square flange (02 version Standard type or tandem housing Torque resistant without 2nd guidance drylin® W - flange bearing drylin® Q - housing bearing Q10 Solid polymer bearing made of iglidur® J Very light Tolerates moments up to 3 Nm Space saving drylin® Q - housing bearing Q10 drylin® Q - accessory Based on a torque resistant square guide with 7.5 mm edge lengths Hollow chamber for supply lines (media, compressed air,cable) drylin® Q - accessory drylin® Q - gripper axis Toothed, hard-coated and corrosion protected square-hollow profile Move loads up to 500 g at speeds of up to 0.7 m/s Bearing made of iglidur® J Drive: NEMA11 stepper motor with gear wheel drylin® Q - gripper axis

Square stainless steel tubular heaters BASE-flex (1.4541) are a reliable industry standard for the use in heating platens and manifolds. In contrast to traditional tubular heaters with a round section which have to be bent by machines, square BASE-flex can be fitted into any rectangular groove with simple hand tools. Moreover, the square shape results in a bigger heat emitting area of up to 80% compared with a corresponding round section. Finally, the easy manual mounting saves the usually high technical expenditure for casting-in / soldering / cementing of bent round tubular heaters. A soft version of the BASE-flex, the NICKEL-flex (2.4068) is available as special execution. Due to the soft, easy to form nickel material, the NICKEL-flex is suitable for manual mounting with hand tools in round sections, too. Furthermore, Nickel has a better capability to conduct heat compared with stainless steel.

plow bolt with square neck M16 in class 8.8, zinc plated

The CEE floor tank 6620A consists of a housing made of stainless steel 1.4301 (3 mm) and a 20 mm thick cover made of anodized aluminum that can be closed with a tool. When closed, the CEE floor tank is not waterproof. In the outdoor area, a drainage pipe must be provided on site for the housing to be drained. Due to the surface load of 6.5t, this version can be driven on with a truck if it is properly installed and the lid is completely closed. The lid opens with the help of a gas pressure spring and can be closed with plugged-in plugs. Other equipment variants on request.

Floor box 8808T with 8 slots made of polished stainless steel. It can be installed at any point in the floor, as pipes are used for the line feed. Because of its low height, this version is particularly suitable for floors in old buildings. The lid is designed for the inlay of carpets, cork floors or the like, with a covering thickness of 5–7 mm, and closes even when the plugs are inserted. Further equipment variants on request.

The housing of the 2008Q floor box is made of 1.5 mm thick V2A stainless steel and has a lockable aluminum lid. The sturdy floor box is passable by car. With a lid seal it is suitable for cleaning with wet sweepers. Correct installation is a prerequisite. The device unit can contain up to 8 installation devices. The sockets have a VDE mark. With internal tube for using the tank with the lid closed. Further equipment variants on request.

Advantages of Heating Plates with Square Cartridge Heaters: -> Simple plate manufacture due to rectangular groove geometry, no deep-hole boring -> Simple heater installation by bending and pressing along the plate surface -> Complex plate geometries with bores and openings -> Optimal heat transfer due to 75% surface contact -> No casting with heat conductive compound -> Uniform temperature profiles due to thermally optimized groove layouts/power distribution and utilization of insulation plates -> high process temperatures (up to 450°C in aluminium, up to 700°C in stainless steel) Example "Heated Stamp": D=100 mm out of tempered tool steel up to max. 700°C continuous temperature. Fitted with 2 Square Cartridge Heaters 1500 W/ 230 V, 4,5 x 4,5 mm x 600 mm, with 50 mm unheated at the termination end. Annealed and formable with a nickel sheath, resistant up to 850°C surface temperature. Connection by fibreglass insulated pure nickel high-temperature leads (max. 500°C)

The square shopping basket made of solid willow is the perfect companion for the next big shopping tour. The two foldable handles lie well in the hand. The angular shape of the basket also fits well in the classic shopping trolleys and hardly takes up any space. The shop equipment in an organic market or farm shop is optimally rounded off with this filling basket in natural design. As a gift basket this article is a popular present.

countersunk head screw with square neck all sizes

mushroom head square neck bolts as per DIN 603 all sizes

Metal trolley for one DURABIN SQUARE 90 waste bin. With four castors. • Carriage made of white-painted metal with four castor wheels • For one DURABIN 90 container for waste and recyclable material

Large, square waste bin. With carry handles for simple transport. Capacity: 90 litres. • Square waste and recycling container made of plastic • Can also be used for transport and storage of raw materials in industry and commerce • With carry handles for easier transport • Food-safe in all colours (according to EU Regulation no. 1935/2004/EC), except for the colour black • Matching lid in various colours and designs available separately • Capacity: 90 litres

Square, 17-litre metal waste basket with integrated 2-litre ashtray. Includes 1.5 kg sand. • 17-litre metal waste basket with integrated 2-litre ashtray • With 2 apertures at the front and at the back • Angular waste basket with removable inner container and ashtray • Ashtray with wire insert complete with 1.5 kg sand filling • Ideal for use in smoking zones and entrances • Dimensions of removable ashtray: 240 x 50 x 240 mm (W x H x D) • Aperture dimensions: 180 x 130 mm (W x H) • Inner container measurements: 380 x 220 mm (H x Ø)

Large, square waste bin. Made of recycled plastic in Blue Angel quality. Capacity: 90 litres. • Square waste and recycling container made of plastic • Can also be used for transport and storage of raw materials in industry and commerce • With carry handles for easier transport • Matching lid in various colours and designs available separately • Uses recycled plastics in Blue Angel quality • Capacity: 90 litres

Square Saver made of ductile and stainless steel casting

Spindle extension consisting of a rigid, hot-dip galvanized key rod and a separate, rigid PE protection tube. Square bars 13 × 13 mm, hot-dip galvanized. Operating square suitable for operating key DIN 3223 E (House connection fittings). Connecting pins in stainless steel v2a. Coupling sleeve made of iron GGG40, galvanised, with slot and VA-Clip-pin (tool-free connection system). PE-HÜLSROHR with centering cap and universal-level bell, dirt-proof and water-repellent

Installation set valve valve, type: rigid, version square

Telescopic Spindle Extension T3 for ball valves with square connection. A two-piece hot-dip galvanised steel rod accord. to DIN EN 10240 (alternatively in stainless steel), square cap (top adapter) made of GJS400-15, galvanised accord. to DIN EN 12329 and DIN 50961 (alternatively in stainless steel AISI 304) with connection drillings accord. to GW336. Suitable for operating key DIN 3223 C or E (DN25-50). Toolles assembly of the spindle extension with a stainless steel clip-pin. Connection pins made of stainless steel 1.4301. Transport security of the rod minimum of 150N. Self-locking in every adjustable position with a PE sealing collar on the steel tube. Torques accord. to GW336. Three-piece PE protection tube system with an additional corrugated protection tube, bonded centring cap and universal round bell accord. to GW336. Completely dirt-proof and water-repellent. Incl.: Integrated position indicator „1/4 turns“.

As a danger protection, for separation and blocking of roads and walkways etc. Blocking of grassed areas and protection of trees, flower beds or as a safety guard in red and white warning colors. Additional powder coating in RAL and DB colors. Access barriers made of round tube Ø 60mm or square pipe 70 x 70mm, available in stationary, removable with triangular locking mechanism and revolving

Baking frame, adjustable • for baking, layering and decorating • made of stainless steel, fruit acid-resistant • extra high 80 mm • adjustable from 155 to 280 mm • fix selected size with the clips – hassle-free

Black Powder Coated Steel Housing and Pull, with Rubber Sleeve.Size:155.6*82.8mm.Maximum static load: 1610N.Easy Installation,ROHS compliance.

• cutting technology for the most discerning • non-slip foot for safe hold on the work-top • practical blade protector

Stainless steel square, other grades availabe on request, cold-drawn. Technical delivery conditions according DIN EN 10088-3:2014. Execution as per DIN EN 10278:1999, tolerance h11. The produced bars are delivered with mill test certificates according to DIN EN 10204/3.1. Available in random lengths of 3000-3200 mm. *The regular minimum order quantity is 500 kg. The finished bars are packed in bundles of approx.500 kg. Each bundle carries two labels, providing information about dimensions, grade, heat number, weight, manufacturer's code and works inspector. Other dimensions on request. Application areas: • Mechanical engineering • Chemical industry • Petrochemical industry • Food industry / agricultural technology • Transportation • Decorative guidelines / kitchen furnishings • Construction industry Special features: • Non-magnetic materials

Stainless steel square, other grades available on request, hot rolled. Technical delivery conditions according to DIN EN 10088-3:2014. Design according to DIN EN 10059. Acceptance test certificates according to DIN EN 10204/3.1 are issued for the manufactured sections. The regular minimum order quantity is 500 kg. We pack the finished profiles in bundles weighing approx. 500 kg. Each bundle is provided with two labels giving information on dimensions, material number, heat number, weight, manufacturer's mark and the responsible mill expert. Fields of application: — Mechanical engineering — power plants — Chemical industry — Petrochemical industry — Food industry/agricultural technology — Aviation industry — Marine equipment — Medicine and pharmaceuticals — Defense technology — Decorative purposes/ kitchen equipment — Construction industry Special properties: — Non-magnetic materials — Materials for low temperatures