Hole punch - Import export

iglidur® clip bearing, metric d1 [mm]: iglidur® clip bearing, inch d1 [inch]: iglidur® clip bearings are especially intended for the shaft bushing through plates. For this reason the bearing has a flange on each of the two front sides. After the clip-on the bearings are secured on both sides in the plate. The clip bearings have chamfered slot on the side that enables the mounting of the bearing on one side. After the mounting the bearing straddles and lines the bore in the plate. The shaft prevents the clip bearing from slipping out of the bore. The bearing cannot slip out of the bore even in axial movements. Extremely simple mounting through lateral slot Maintenance-free and self-lubricating Good flexibility in punch hole Good abrasion resistance Quiet operation Suitable for rotary and linear movements Extendibility through the slot Undetachable through double flange Special dimensions possible Plate thicknesses from 3 mm to 4 mm available from stock Material: iglidur® M250 Special properties of the iglidur® clip bearings iglidur® clip bearings are made from the most abrasion-resistant material, iglidur® M250. iglidur® M250 is a bearing material for rugged, wear-resistant bearing systems for medium loads. The bearings are self-lubricating and can be used dry. If required the bearings can also be lubricated. The material iglidur® M250 is resistant to all common lubricants. The iglidur® clip bearings are the ideal solution for bearing functions with low loads. The easy mounting makes it ideal for applications with difficult bearing locations. Compressive strength The permitted static surface pressure of iglidur® M250 amounts to 20 MPa at room temperature. Due to the good adaptability to uneven surfaces of the bearing housing, a high pressure load capacity of the clip bearings persists even in punched holes. For the most small bearing surfaces, the good vibration dampening properties and the insensitivity to misalignment are of primary importance. Surface speeds Clip bearings are particularly wear resistant in slow rotating, oscillating and axial motions. You can find the maximum gliding speeds for the various motions for the iglidur® M250 material under the materials data link shown below. A lubrication at installation or continuous lubrication raises the permitted surface speeds. Clip bearings are available from stock in dimensions of 3 to 25 mm. Fixation Triflex RS For mounting, the bearings are laterally pressed together with the large flange. The chamfered slot makes the bearing spiral-shaped, whereby it can be easily inserted in the plate. The remaining slot in the attached clip bearing can compensate for linear expansions of the circumference. Thus narrow bearing clearances are possible with clip bearings. The bearing clearance is dimensioned in such a way that in a housing bore with a nominal diameter, a shaft made with the same nominal diameter turns easily. The clip bearing can be used in H-tolerance housings up to H13. The turning of the clip bearing in the bore is also permitted. Operating temperatures The wear resistance of the iglidur® clip bearings are excellent with operating temperatures till 80°C. Even at low temperature the bearings remain elastic and abrasion resistant. When to use it? When a sheet metal feedthrough is required When the bearing should be captively clipped on in a drill hole with rough tolerance For rotating, linear and pivoting movements When a quick-mounting bearing solution is sought Clip bearings application examples When not to use it? When constant temperatures of more than +80°C occur iglidur® G When a high-precision bearing is needed iglidur® J When the housing bore is more than 4 mm long iglidur® Clips 2 iglidur® MKM When very high surface pressures occur iglidur® G iglidur® clip bearing, metric d1 [mm]: iglidur® clip bearing, inch d1 [inch]:

Labelling systems can be integrated, whether it is laser, needle or inkjet, to mark and identify the tubes. Other options that can be integrated are welding seam detection, length control or measurement of processed tubes. The corresponding sensor and camera technology can be implemented for the specific product. The following step can be carried out without any problems, whether it is cutting, punching, deburring of holes or seal testing with external systems. Smart data evaluation All the systems can be equipped with different control and IPC panels. Interfaces to data caption systems for consumption and operation make the digitalization and evaluation of the data. Marking system, Welding seam detection, Camera control system, Internal and external cleaning processes, Cleaning and suction, Hole punching, Deburring – chamfering

Useful information rack for A4, A5 or 1/3 A4 wire holders (not included). For this purpose, the brochure compartments are simply inserted into the small, punched holes of the metal surface. Furthermore, it can be equipped with plastic poster holders, see accessories. These adhere to the steel rack by means of glued magnetic strips. Posters and information can be changed very easily. Open pocket - insert poster - close pocket. Your information and brochures will be put into the right light with the optionally available halogen light. The information stand is available in a narrow and wide version. Prices without wire holders and poster pockets!

Transparent punched pocket made from PP. With reinforced punched holes 45 x 65 x 45 + 80 mm. • Indelible punched pocket made from polypropylene • With reinforced punched holes • Punching: 45 x 65 x 45 + 80 mm for filing in A5 format ring binders • Open at the top • Format: A5 landscape

Cable cover plates with increased mechanical protection Manufactured acc. to DIN 54841-5 Standard design: Material: PE-HD Length: 1.000 mm Surface colour: red Thickness: 10 mm Labelling: Achtung Starkstromkabel Longitudinal locking: with punched holes and connection pin Possible designs: Cover width: 100 mm to 290 mm Length: 300 mm to 3.000 mm Thickness: 3 mm to 12 mm Material: PE-HD or PVC-U Surface colour: yellow, blue, green, orange, black Longitudinal locking: with or without punched holes and connection pin Labelling: acc. to customer specifications

The perforated metal plank type BN-OP5 “Noppe, offen plus, 5mm“ was especially developed for pedestrian areas with „High Heel Proof“ requirements. The bothsided punched holes have a diameter of 5mm. The punching sequence corresponds to BN-OP7. This type of planking offers high slip resistance and also allows ladies in stiletto heels to walk safely on the gratings. Due to the small hole configuration it is difficult to see through from underneath, which is important in public access areas. The perforated metal plank type BN-OP8, corresponds to type BN-OP5 in terms of the punching pattern, but have twice the number of holes. The drain holes have a diameter of 8 mm and thereby increase the drainage performance and light and air permeability..

The perforated metal plank type BN-OD „Noppe, offen , different“ is characterised by two different hole sizes. The bothsided punched holes have upwards a diameter of 14 mm and downwards a diameter of 7 mm.

The perforated metal plank type BR is particularly suitable for areas of heavy loads on small contact areas due to its rhomb profile with extra high punching (punched holes 2.5 mm). Here, for example, vehicle navigability on ramps or parking areas are to be considered.