Hall sensors - Import export

The completely equipped electrical cylinder unit includes the motor transmission unit, along with the motor brake, two-channel Hall-IC sensor and two end-limit switches. All connection lines run directly out of the unit to make configuration and initial start-up easier, particularly for PLC operation. The fixation of the electric cylinder connections is compatible with commercial pneumatic and hydraulic cylinders.

Cylinder magnet is also known as rod magnet, it is a magnet with its length larger than diameter, this gets the magnet to generate very high level of magnetism from a relatively small surface pole area. Cylinder magnet has high "Gauss" values because of its greater magnetic length and deep depth of field, making them ideal for activating reed switches, hall effect sensors in security and counting applications, also it is ideal for educational, research and experimental uses. We are ready to make a custom cylinder magnet for your application, welcome to contact us for a further communication.

Angle position measurement by means of Hall sensors and signal processing including generation of the analogue output signal. Robust brass housing – stainless steel shaft with sliding bearing – sensor circuit consisting of ASIC with Hall elements – electrical connection via connector.

Recording of the angular position by means of Hall sensor and signal processing, including generation of the analogue output signal. Incrémental ou absolu: Absolu

Recording of the angular position and revolutions by means of Hall sensors - absolute multiturn transmission for up to 4096 revolutions - data output plus parameterisation and diagnosis via EtherCAT. Robust housing (housing sickness 5 mm) manufactured from seawater-resistant aluminium (AlMgSi1) or stainless steel - stainless steel shaft - ball bearing with shaft seal - sensors circuit consisting of ASIC with Hall elements - electrical connection via M12 connector or cable outlet. In the model series TRK absolute encoders, the EtherCAT interface is integrated according to IEC 61158-2 to 6 and encoder profile CiA DSP406. As a "full slave", the TRK supports all EtherCAT addressing modes such as logical addressing, position addressing and node addressing. Use of the CANopen over EtherCAT message and the CANopen encoder profile enable parameter and diagnostic data handling as familiar from CANopen. These are contained in an object directory under the same indices as in the case of CANopen.

Recording of the angular position and revolutions by means of Hall sensors - multiturn version with absolute transmission for up to 4096 revolutions - data output plus parameterisation and diagnosis via Profibus-DP. Robust housing manufactured from seawater-proof aluminium or stainless steel - stainless steel shaft - ball bearing with radial shaft seal - sensor circuit consisting of ASIC with Hall elements - electrical connections via the connecting cap with threaded cable connections. The absolute encoders are designed for direct connection to the PROFIBUS-DP. The interface is implemented with the SPC3 Siemens PROFIBUS controller. The protocol corresponds to DP-Slave Class 2 functionality in accordance with Profibus profile for encoders, No. 3.062, and is described in detail in the TRD 12770 user manual. The TRD is mechanicallly and electrically compatible with the electro-optical encoder CRD.

Recording of the angular position and revolutions by means of Hall sensors - absolute multiturn transmission for up to 4096 revolutions - data output plus parameterisation and diagnosis via EtherCAT. Robust housing manufactured from seawater-resistant aluminium or stainless steel - stainless steel shaft - ball bearing with radial shaft seal-sensor circuit consisting of ASIC with Hall elements - electrical connection via M12 connector or cable outlet. In the model series TRK absolute encoders, the EtherCAT interface is integrated according to IEC 61158-2 to 6 and encoder profile CiA DSP406. To achieve the SIL2 level, the TRK/S3 contains a redundant sensor system and additional internal monitoring mechanisms as well as safe communication via the FSoE (failsave over EtherCAT) protocol. The FSoE protocol is implemented according to the Safety over EtherCAT specification ETG.5100 version 1.2.0.

Recording of the angular position and revolutions by means of Hall sensors - multiturn version with absolute multiturn transmission for up to 4096 revolutions - data output plus parameterisation and diagnosis via PROFINET. Robust housing manufactured from seawater-resistant aluminium or stainless steel - stainless steel shaft - ball bearing with radial shaft seal-sensor circuit consisting of ASIC with Hall elements - electrical connection via M12 connector or cable outlet. The Profinet interface according to IEC 61158 / 61784 or PNO specifications order No. 2.712 and 2.722, version 2.2, is integrated into the model series TRT absolute encoders. Real time classes 1 - 3 are supported, i.e. Real Time (RT) and Isochronous Real Time (IRT) plus the requirements of conformance class C. Setting the address, baud rate or terminating resistances is not necessary. A name, which is stored in the absolute encoder's non-volatile memory, is assigned via the PROFINET controller to address the device.

Recording of the angular position and revolutions by means of Hall sensors - data output plus parameterisation and diagnosis via PROFINET. Robust housing manufactured from seawater-resistant aluminium or stainless steel - stainless steel shaft - ball bearing with radial shaft seal-sensor circuit consisting of ASIC with Hall elements - electrical connection via M12 connector or cable outlet. The Profinet interface according to IEC 61158 / 61784 or PNO specifications order No. 2.712 and 2.722, version 2.2, is integrated into the model series TRT absolute encoders. Real time classes 1 and 3 are supported, i.e. Real Time (RT) and Isochronous Real Time (IRT) plus the requirements of conformance class C. To achieve the SIL2 level, the TRT/S3 contains addtitional internal monitoring mechanisms as well as safe communication via PROFIsafe. The PROFIsafe protocol is implemented according to the PROFIisafe Profile for Safety Technologie version 2.4 (PNO Order No. 3.192)

Recording of the angular position and revolutions by mens of Hall sensors - multiturn version with absolute transmission for up to 4096 revolutions - data output plus parameterisation and diagnosis via Profibus-DP. Robust housing manufactured from seawater-proof aluminium or stainless steel - stainless steel shaft - ball bearing with radial shaft seal - sensor circuit consisting of ASIC with Hall elements - electrical connections via the connecting cap with threaded cable connections. The absolute encoders are designed for direct connection to the PROFIBUS-DP. The interface is implemented with the SPC3 Siemens PROFIBUS controller. The protocol corresponds to DP-Slave Class 2 functionality in accordance with Profibus profile for encoders, No. 3.062, and is described in detail in the TRD 12770 user manual. The TRD is mechanicallly and electrically compatible with the electro-optical encoder CRD.

•Supply voltage: 14V - 65V •Phase current: 300A •Motor types: PMSM •Control algorithm: Field oriented control with flux weakening •Functions: Automatic teach-in, four ride modes, reverse gear, boost, display control, smartphone app •Position feedback: Hall sensor •Analog inputs: 2 •Digital inputs: 2 •Communication: CAN, Smartphone Connectivity •Diagnostic interface: USB, CAN •Diameter: 155mm •Height: 45 mm •Weight: 970 g