Dusts - Import export

CF 30 G equipment is supplied completely assembled and ready for operation. The dust collection unit is suited for intermittent operation only, because regular cleaning of the pocket filter element in certain intervals is an absolutely must for the proper operation of the equipment. The cleaning intervals will depend on the operating conditions and must be established by experience. Normally cleaning intervals will be between operating times of 30 minutes to two hours. It is a prerequisite for sufficient and intensive cleaning of the filter cloth that dust collecting is interrupted during cleaning to achieve static pressures on the filter material. A retention time of 1 - 2,5 minutes between the end of the suction and the beginning of the cleaning process is therefore required. The filtered air must be removed outside - do not lead back to closed rooms!

With high-quality filter tubes and PTFE diaphragms. Paint dust filters Wet painting also results in overspray. Overspray is the solid portion of the paint that is not taken up by the workpiece. According to the purpose of use, the overspray is moist and sticky immediately after release. It is captured by the exhaust air stream in the spray booth and fed to a filter. This can be, for example, a baffle plate filter, paper filter, fleece filter, glass fibre filter or also combinations of these. The adhesive effect causes the paint particles to adhere to the contact surfaces of the respective filter medium, as a result of which a good degree of separation is achieved. However, all these filters are storage filters, i.e. the filters clog up more and more during operation and cannot be regenerated. A filter exchange becomes necessary if the exhaust air rate of the spray booth falls below the minimum. This can be very time-consuming under certain circumstances and the work process must be interrupted in order to do it. To make things worse, not only must the filtered and bound paint residues be disposed of, but also the actual filter materials. Such tooling times are not justifiable for automatic, continuous or multi-layer painting processes. Continuous procedures such as automatically cleaned filters are likewise required for this. The humidity and the adhesiveness of the particles to be filtered are thereby the problem. In order to solve this problem, the paint particles should be relieved of their adhesive capability as far as possible whilst still inside the paint booth. Our patented ‘RTS-Rotation’ system is outstandingly well suited for this. The system is comprised of slowly rotating brush rollers, which take up the adhesive paint particles on the surface of the bristles and allow them to dry there. The bristles are automatically regenerated at pre-specified time intervals by combing devices that swing in at the rear of the brush rollers. The dislodged paint residues can then be removed and disposed of either manually during work breaks or automatically during operation. The degree of separation of this system is, however, insufficient to satisfy the environmental protection requirements concerning residual dust content in the exhaust air. A further filter stage is necessary for that. It must be assumed that the paint particles arriving here are to a certain extent still damp and sticky. For this we use special paint dust filters with high-quality filter tubes with PTFE diaphragms. If necessary, precoating agents (auxiliary dust) are used in order to neutralise the adhesive capability of the particles and to keep the dust layer on the filter elements permeable to air. The precoating agent is injected into the raw air pipe by means of special dosing units. The filter tubes are cleaned by means of compressed air impulse cleaning. The use of this technology requires special know-how. We have had the appropriate experience for almost ten years. The implemented plants have capacities ranging from 5,000 to 90,000 m³ /h. Because of the large number of different paint systems, individual experiments are usually necessary in our pilot plant in order to find the correct solution for the individual case.

To ensure that your anchorage devices are securely installed in a concrete surface or masonry, the bore holes should be carefully cleaned prior to using special adhesive. This dust pump is designed to quickly remove any dust or residual particles that might cause problems from the bore holes. High capacity Air chamber length: 42 cm

Vshaped arranged filter plates from closely pleated 4layer filter media composite nonwoven from electrically uncharged, organic, synthetic microfibres and activated carbon grains rugged KALTHOFF filter casing of plastic doubleworking arrester very high adsorption kinetics conditions for mounting and service optional at site

ISO CoarseISO ePM10 / G4M5 pleated, progressivelystructured filter media thermallybonded, synthetic nonwoven (polyester) hotmelt pleating system synthetic FIBERPLAST frame standard installation depths 20, 25, 47, 92 mm special design with different frame geometries simple handling optimum resistance performance through hotmelt pleating system low pressure drop moistureproof fully combustible

synthetic filter media or filter media with irregular layer of coarse glass fibres individual pads or filter rolls available small installation depth low acquisition costs

The MIXACO discharge stations are used for dust free emptying of the product into the further processing step (e.g. dosing system into an extruder). The container is fixed in place when moved into the discharge station. Two different executions are available: Type Guide fork Type Platform Differentiated by the way of feeding the container. Type Guide fork The movable container is pushed by means of its own wheels into the discharge station type guide fork and is locked in place. A pneumatic coupling is used to connect the discharge pipe to the container discharge valve. Type Platform The container is placed onto the emptying station with the aid of a lifting device (crane or forklift). Equipment Positioning of the container Pneumatic coupling between container and the further production step Pneumatic rotary cylinder for automatic opening / closing of the container discharge valve (0/90°)

MIXACO Charging station The MIXACO charging station is used for dust free filling of the mixing container with raw materials. In conjunction with a bottom weighing scale or dosing systems, a fully automatic, a semi-automatic or manual charging of the container can be carried out.

The application of CO 2 ice jet spraying is convincing. Ranging between CO 2 cleaning and high-performance dust removal with regard to quality, optimum pretreatment can be accomplished with this system variant, only requiring simple workpiece fixing and little noise protection measures. DUST FREE can be flexibly integrated in existing equipment. A cleaning jet consisting of a mix of compressed air, CO2 and CO2 ice particles causes the soiling on the surface to become brittle. The thermal tension loosens cohesion and detaches the soiling from the workpiece surface. The cleaning jet guarantees the removal of soiling without residue. The DUST FREE and PERFECT applications optimally meet the requirements of the subsequent downstream surface quality, offering maximum thoroughness from dust removal through to cleaning. This process allows gentle cleaning of virtually all components, therefore, it is an alternative to aqueous power washing. Patented detail solutions form the basis for this mature system technology. Small workpieces are reliably held in place by the special hold-down system. The Venjakob pump station developed for this task guarantees the process reliable supply of liquid CO 2 from a low pressure tank system to the cleaning module. A clear advantage of the CO2 cleaning system over the conventional aqueous cleaning process is its relatively small space requirement. Additional decisive advantages of this system are:

The adapter pieces are made to order in accordance with your specifications.

The impact elements consist of three components which are connected to each other by hot vulcanisation a special rubber mix with a shore hardness of 62° A which absorbs the occurring drop energy a coating of highly sliding UHMWPE and a thickness of 12 mm a vulcanised aluminium profile for easy installation of the bars

high level of dust sealing at the location where material is fed onto the belt conveyor minimal wastage a buffer for the material falling onto the belt conveyor reduced cleaning costs increased conveyor belt service life increased operational safety simple assembly no welding necessary exchange of the adapter piece for existing conveyor rollers Measurements of the impact bars approx. 1240 x 100 x 75 (L x W x H) The impact bars can be fitted using the enclosed screws optimal alignment of the skirting rubber on the conveyor belt

The filter housing is made of sturdy steel plate with a reinforcement of structural steel frame. Equipped with inlet and outlet openings for the dusty or filtered air. The inspection cap is used to control the automatic filter and has a flap for access to the built-in filter cartridges. These are made of folded polyester material having a filter area of each of 8 and 14 m². Provided with upper and lower reinforcing rings of plastics material for fastening in the holders. The dust drawer is equipped with wheels, allowing easy extraction during disposal of the dust. The centrifugal fan with a flanged electric motor and the fan / motor unit is built up in the filter housing - the motor is bolted with its flanges on the filter housing and surrounded by the sound enclosure.

It is a system that is preferably used for small blasting and glass decorations. The closed blasting circuit, which allows dust-free operation (particularly interesting for sandblasting work on already installed objects), is advantageous. The system of the "multi-CIean master" means e.g. The solution for the blasting of small surfaces on large parts of machines and vehicles, which can not be disassembled or transported into a blasting space. Due to its extremely light and compact design, it is also possible to use it on construction sites, scaffolds or e.g. Pipelines possible. This system also offers an alternative for cleaning with toxic chemicals or for complex grinding or brushing. A thorough cleaning or removal of rust, scale or similar deposits can also be carried out without having to perform costly and costly disassembly.

The Modellrange ECONOMIC is made of durable sheet steel. It comes with adjustable media consumption, a blast media collection bin and a sieve to separate blast media from contaminations. The cabinet has two lateral openings with sealing sliders for rod materials. A perforated metal plate with enforcements. The system has a sectional door that opens the complete workspace. The Cabinet comes with a door-safety switch, two large operation holes with multiple rubber Sealings. Monitoring window, sized 400x500 mm, with easy changeable glass/safety-glass panes, as well as 2 durable pneumatic springs. Energy Saving Lamp, attached from outside. Injector-type blast head, with air- and blast nozzle made of hardened steel. The system comes with all necessary compressed air and blast media hoses, oil-water separator, manometer, an electrical magnet valve and a foot switch. On/Off switch, dust filter system 0,55 kW, intermediate pressure turbine. Dust collection bag.

Special features of our model range SUPER BABY: • Compact and elegant design • Simple operation • Low material consumption • Highly efficient dedusting • Efficient function • Environment-friendly function without dust harassment • Adjustable material consumption The SUPER BABY has a large door that opens to the top and allows to put in the work pieces easily. Due to the mounted sinkhole the blast media circulation is possible without any other additional equipment. With the controls to adjust the blast media it is easy to adjust the blast-media consumption and to change the blast media type. A built-in nozzle-holder and an injector type blast-head with hardened air- and blast nozzle (manual operation), as well as a working grid allow an easy operation. A Shock-resistant linear fluorescent luminary gives glare-free light in the work area. Efficient injector sandblasting booth Superbaby. Direct from manufacturer, MADE IN GERMANY.

The HL-Druckstrahl-Rücksaug-System for the mobile, dust-free sandblasting of hard / non-dismountable parts, such as steel carriers, running gear or similar large parts. The Mega Clean Master is often used in car body repair shops, shipyards, but also in road and rail traffic. The Mega-Clean-Master is the optimal solution for parts that are difficult to access or can be dismantled, which have strong corrosion or stubborn lacquer parts. Mobile, efficient, dust-free, and thanks to the built-in high-performance print-jet system, the perfect companion for difficult-to-clean parts.