Load switches - Import export

Housing, die-cast zinc. Housing cover, plastic, self-extinguishing. Hinge bolts, die-cast zinc/steel C45. Contacts, silver-nickel alloy 10. Note: The security hinge switches are used for monitoring the position of swing-hinged safety doors, protective hatches and hoods. The protective device is monitored directly in the hinge. By the universally pre-set versions, the switching angle is freely adjustable over the entire working range. A mounting aid ensures the quick alignment to doors and posts. The additional hinges have the same appearance and dimensions as the security hinge switches. The loading values given for the hinges are non-binding reference values without consideration of safety factors and exclude any liability. The values given are for information purposes only and do not constitute a legally binding assurance of properties.

CD3000S 2PH two leg switching three wire load star or delta resistive loads or infrared lamps up to 90A. Fully isolated from power. Zero crossing firing available with logic input signal (SSR) Constant current drain with SSR input Analog input 4÷20mA or 0÷10V with burst firing 4, 8 or 16 cycle at 50% power demand, is available as an option from 35A to 90A. Heater break alarm (HB) to diagnostic partial or total load failure and short circuit on thyristor, is available as an option from 35A to 90A Side by side mounting. Special design for heatsink with high dissipation Comply with EMC specification CE and cUL

One pole on-load switch for indoor use.

The EME on-load switch for indoor use type GP1 is designed to break currents up to 630A. This switch is also available in combination with an earthing device, capacitive insulators, etc.

The EME on-load fuse switch for indoor use type GP2V is designed to break currents up to 630A. An intelligent system realises the 3-phase opening of the switch when one or more fuses have tripped. The switch can also be opened by means of a delayed under voltage release or trip coil, can be equipped with an earthing device, etc.

With rotary control, two-way switch and soft-catch. 2-wire connection (neutral conductor not required) Optimised for dimming of retrofit LED lamps (LEDi). For dimmable Retrofit-LEDs (LEDi). For dimmable Retrofit-LEDs (LEDi) with conventional or electronic transformers. For incandescent lamps, 230 V tungsten halogen lamps, low-voltage halogen lamps with conventional or electronic transformers and dimmable energy-saving halogen lamps. Mix operaton of LEDi with conventional loads possible. Via mode switch adjustable between leading edge control and trailing edge control. Low-noise level by MOSFET transistors. With electronic short-circuit protection. With electronic overload protection. With adjustable minimum brightness. Without cover plate. Rated voltage: 230 V~, + 10% / - 10% Rated frequency: 50 Hz/60 Hz Nominal power: 2 - 100 W/VA (retrofit LED loads). Nominal power: 10 - 250 W/VA (non-LED loads).

This external bypass module is intended for use with UPS FROSTYLE11, 13 kVA. In Normal Mode, the UPS connects to utility power through the bypass module and provides uninterrupted power to the load. In Bypass Mode, the load is switched to power directly from the external network, bypassing the UPS circuits. The UPS input and output are completely isolated from the loads and the mains. In this mode, the UPS can be safely (and without disconnecting the load) removed from the system for maintenance or replacement

Product Features: • Roxburgh's EMC range of three phase RC networks are suitable for a variety of applications. These RC networks are available three phase (3CRH) or single phase (CRH). • The 3CRH series of RC networks is three phase, 0.33μF 33Ω or 0.47μF 27Ω. Rated at 500V these spark quenchers are designed to reduce arching when switching reactive loads. The CRH series is fitted with flying leads.

Product Features: • Roxburgh EMC's range of single phase RC networks are suitable for a variety of applications. These RC networks are available single phase (CRH) or three phase (3CRH). • The CRH Series of RC networks is single phase, 0.33μF 33Ω or 0.47μF 27Ω. Rated at 500V these spark quenchers are designed to reduce arcing when switching reactive loads. The CRH Series is fitted with flying leads.

Product Features: • A range of single phase RC networks rated at 275V, with PCB leads. • The RE Series or RC Networks is very similar to the XE range, but maintains a higher voltage rating of 275V. They hold various safety approvals, are of a compact size and have a good peak pulse withstand capability. • The products are suitable for a range of AC and DC applications including suppression when switching reactive loads, and as a snubber network in SCR and triac protection. • Approvals include: UL, CSA, VDE, SEV, SEMKO, NEMKO, FIMKO, DEMKO and RoHS.

Product Features: • Roxburgh EMC's range of networks are suitable for a variety of applications. RC Networks are available with PCB Mounting (XE) or flying leads (XEB). • The XE Series or RC Networks has PCB mounting and is available with 0.1μF 120Ω and 0.2μF 120Ω. Rated at 250V the RC Networks consist of a capacitor in series with a high quality film resistor. • Applications include suppression when switching reactive loads, and as a snubber network in SCR and triac protection. • Approvals for the XE range include: UL, CSA, VDE, SEV, SEMKO, NEMKO, FIMKO, DEMKO and RoHS.

Product Features: • Roxburgh EMC's range of RC networks are suitable for a variety of applications. RC Networks are available with flying leads (XEB) or PCB mounting (XE). • The XEB series of RC Networks has flying leads and is available with 0.1μF 120Ω and 0.2μF 120Ω. Rated at 250V the RC Networks consists of a capacitor in series with a high quality film resistor. • Applications include suppression when switching reactive loads, and as a snubber network in SCR and triac protection. • Approvals for the XEB range include: UL, CSA, VDE, SEV, SEMKO, NEMKO, FIMKO, DEMKO and RoHS.

KATKO produces an extensive range of safety switches, load break switches, switch fuses, and motor protection switches in addition to accessories for them.

IC LOAD SWITCH SOT25 Digi-Key DIST Single 5.5V 3A 5-Pin SOT-25 T/R Arrow

The TPS22965DSGR is a 6A load discharge, slew rate controlled N-Channel 8-WSON (2x2) general purpose power distribution switch with a wide operating temperature range of -40°C to 105°C (TA). It is designed to provide a low-cost, low-power solution for power distribution applications. The device features a low on-resistance of 0.3Ω and a low quiescent current of 0.2μA. The device also features a slew rate control function that allows for a smooth transition between on and off states. Features: • 6A load discharge • Slew rate controlled • Wide operating temperature range of -40°C to 105°C (TA) • Low on-resistance of 0.3Ω • Low quiescent current of 0.2μA • Slew rate control function for smooth transition between on and off states • N-Channel 8-WSON (2x2) general purpose • 2.5 V ~ 5.7 V operating voltage Applications: The TPS22965DSGR is suitable for a wide range of power distribution applications, including automotive, industrial, and consumer electronics.

The VNQ5050KTR-E is a high side power distribution switch and load driver integrated circuit (IC) from STMicroelectronics. It has an operating temperature range of -40°C to 150°C (TJ) and is packaged in a 24-SOP (0.295", 7.50mm Width) Exposed Pad SMD/SMT package. It has a minimum supply voltage of 4.5V and a non-inverting configuration. The turn-on delay time is 15000 ns and the ratio of output to input is 1:1. It is available in Digi-ReelR Alternate Packaging.

The IPS511G IR Integrated Circuits (ICs) Power Distribution Switches, Load Drivers are designed to provide a high side switch with a 1:1 ratio of output to input. The device features a non-inverting input type, a voltage load of 5.5 V ~ 35 V, a TO-220AB (5-LEAD) supplier device package, an operating temperature of -40°C ~ 150°C (TJ), a Rds-On-Typ of 110 mOhm, a general purpose switch type, a TO-220-5 package case, and one output. Features: * Non-inverting input type * Voltage load of 5.5 V ~ 35 V * TO-220AB (5-LEAD) supplier device package * Operating temperature of -40°C ~ 150°C (TJ) * Rds-On-Typ of 110 mOhm * General purpose switch type * TO-220-5 package case * One output Applications: The IPS511G IR Integrated Circuits (ICs) Power Distribution Switches, Load Drivers are suitable for a variety of applications, including automotive, industrial, and consumer electronics. They can be used to control power distribution, switch loads, and drive motors.

The ZETEX BSP75GTA is a N-Channel INTELLIFET® SOT-223 General Purpose Power Distribution Switch and Load Driver with a maximum voltage of 60V. It features a 1.6A Auto Restart and an operating temperature range of -40°C to 150°C (TJ).

The MP5087GG-Z is a high-side load driver designed to provide high-efficiency, high-performance power distribution for general purpose switching applications. This device provides an output voltage range of 0.5 V to 5.5 V with a maximum current output of 7A, making it suitable for use in a wide variety of industries. It has an operating temperature range of -40°C to +125°C and a Rds-On-Typ of 10 mOhm. The switch type is general purpose with one output, packaged in a 12-QFN (2x2) and is powered by a voltage supply of 3 V to 5.5 V. Features: - High-efficiency, high-performance power distribution for general purpose switching - 0.5 V to 5.5 V output voltage range with 7A maximum current output - Operating temperature range of -40°C to +125°C - Rds-On-Typ of 10 mOhm - General purpose switch type with one output - 12-QFN (2x2) package - 3 V to 5.5 V voltage supply Applications: The MP5087GG-Z is suitable for a variety of industrial applications

The TPS1H100AQPWPRQ1 is a high-side power distribution switch and load driver from Texas Instruments. It is designed to provide a high-side switch with a low on-resistance of 0.2Ω and a low quiescent current of 0.5mA. It is suitable for applications such as automotive, industrial, and consumer electronics

The Allegro A2982SLWTR-T is a power distribution switch and load driver designed to provide a high-current, low-voltage, low-side switch for a wide range of applications. It is a bipolar 20-SOIC W package with a 500mA current rating and a temperature range of -20°C to 85°C (TA)

The ALLEGRO Power Distribution Switches, Load Drivers UDN2981A are 18-DIP package bipolar output type devices that offers 8 outputs which are configured on 1:1 ratio of the output to the input. This device does not require voltage supply Vcc or Vdd, making it a very efficient device. Its electrical parameters lie within the range of a 5 V to 50 V voltage load.