CD3000S 2PH two leg switching three wire load star or delta resistive loads or infrared lamps up to 90A. Fully isolated from power. Zero crossing firing available with logic input signal (SSR) Constant current drain with SSR input Analog input 4÷20mA or 0÷10V with burst firing 4, 8 or 16 cycle at 50% power demand, is available as an option from 35A to 90A. Heater break alarm (HB) to diagnostic partial or total load failure and short circuit on thyristor, is available as an option from 35A to 90A Side by side mounting. Special design for heatsink with high dissipation Comply with EMC specification CE and cUL
Italy
CD3000S 1PH is a compact low cost family of solid state switches designd to replace contactors Single-phase thyristor units up to 90A. Applicable for resistive loads and infrared lamp. Zero crossing firing available with logic input signal (SSR) Constant current drain with SSR input Analog input 4÷20mA or 0÷10V with burst firing 4, 8 or 16 cycle at 50% power demand, is available as an option from 15A to 90A Heater break alarm (HB) to diagnostic partial or total load failure and short circuit on thyristor, is available as an option from 15A to 90A Side by side mounting Special design for heatsink with high dissipation IP20 protection Comply with EMC specification CE and cUL
Request for a quoteItaly
REVEX is a real Universal Unit where you can select: • Input signal in digital mode, no link jumpers inside • Firing mode: Burst Firing, Zero Crossing • Voltage, Current and Power or V2 and I2 • Communication RS485 with Modbus® protocol std. • Two Analog input • Two Digital input • USB port to program REVEX, should you ever need to re-program from your ordered configuration • With the units already programmed you can simply switch On and Go • Save money and time straight out the box without the need to read a long manual • Save money with REVEX and only pay for functionality you need
Request for a quoteItaly
REVEX PA is the latest born in the REVEX family. The REVEX are positioned between the two families REVO S and REVO C in terms of price and performance. The main characteristic is that they can be configured according to your needs by eliminating of all options that you do not want to use, in order to reduce the purchase price. It is an extremely flexible and performing unit. The REVEX PA is a three-phase unit with higher functions compare to the other REVEX 3PH models, because it is able to carry out phase angle firing with or without Current Limit. REVEX PA is therefore a unit suitable for driving inductive loads, such as three-phase transformers. The algorithms inside the unit allow the control of the power even for special loads, such as MoSi2 and SiC heating elements. It is suitable for controlling both normal resistive loads and short, medium or long wave infrared lamps.
Request for a quoteItaly
SCR Power Controller Unit suitable for resistive and medium or long wave infrared loads Current range – 30A, 35A, 40A, 60A, 75A, 90A, 120A, 150A, 180A, 210A, 300A, 350A, 400A, 450A, 500A, 800A Voltage Range 480V, 600V and 690V (starting from 60A) Fully isolated from the power Zero crossing firing mode (ZC) or Burst Firing (4, 8 or 16 cycles selectable) Logic input signal 4 to 30V DC typical (SSR) plus 4-20mA or 0-10V DC Linear input as an option Constant current drain, independent of supply voltage with SSR input Heater Break (HB) alarm to diagnose partial or total load failure with automatic setting, relay alarm output and front LED indication. Available as an option Side by side mounting Special design Heatsink with high dissipation value IP20 protection Complies with EMC, EAC, cULus® 508 listed and cUL® listed up to 500A as an option. UL® for 800A as an option.
Request for a quote