Acceleration sensors - Import export

For use in harsh industrial environments, special sensors in particularly robust housings must be used. A water- and oil-tight cable connection is also often required, such as that offered by the M608A11 model. To protect against electromagnetic interference, a housing-insulated sensor construction and special amplifier electronics are used. Interference on the cable is also minimised by using twisted pair cables with additional shielding. Typical applications of such sensors include engine and transmission test benches as well as machine endurance test benches. — Industrial ICP®/IEPE accelerometer with integral 3m cable, terminating on cut-off cable -Measuring range ±50 g. — Sensitivity: 100 mV/g — Frequency range: 0.5 to 10000 Hz — With metric (M) or imperial mounting bolt For an individual quotation please contact us directly.

In order that the orientation of sensors with lateral cable outlets can beselected as required, a design with a through-hole is usually used. Thanks to the patented Swiveler® mounting system, the sensors of the M607 series can be Swiveler® mounting, the sensors of the M607 series also allow the cable to be aligned. This allows for a smaller design. Thanks to the patented Swiveler® mounting system, the sensors of the M607 series can be Swiveler® mounting, the sensors of the M607 series also allow the cable to be aligned. This allows for a smaller design. — Industrial ICP®/IEPE accelerometer with integrated 3m cable — Measuring range ±50 g — Sensitivity: 100 mV/g — Frequency range: 0.5 to 10000 Hz — With metric (M) or inch mounting bolt — Weight: 31 g For an individual offer, please contact us directly.

Usually, acceleration sensors with ICP®/IEPE technology are used for vibration monitoring. Sensors for series use are particularly suitable if a large number of measuring points are to be monitored. The low-cost sensor models, where the sensor model 627A01 belongs, can be integrated permanently into monitoring systems or used in conjunction with a portable data collector/analyzer for route-based monitoring. The accelerometer presented here, model 627A01, can be used in ambient temperatures up to 121 °C. If the operating conditions require it, this model is also available with EX approval or with SIL-2 declaration. All sensors are supplied with 1-point calibration according to ISO 17025. The industrial accelerometer, model 627A01, is equipped with a quartz sensing element. — Measuring range 50 g — Sensitivity 100 mV/g — Frequency range 0.33 ... 10,000 Hz — Single-point calibration at 100 Hz — 2-pin connection socket on top For an individual offer, please contact us directly

The sensor model M625B01 with side connection is suitable for a wide variety of standard applications with a measuring range of 50 g. The industrial precision sensors operate in the frequency range up to 15 kHz and can be used in an ambient temperature up to 121 °C. Acceleration sensors with a low lower limit frequency and high sensitivity are available for monitoring very slowly rotating machines. For these models, the discharge time constant has been extended so that the sensor can be used at speeds below 12 rpm (0.2 Hz). —Measuring range ±50 g -Sensitivity: 100 mV/g -Frequency range: 0.33 to 12000 Hz - 2-pin connector on top -With metric (M) or inch mounting bolt For an individual quotation please contact us directly.

Acceleration sensors with ICP®/IEPE technology are usually used for vibration monitoring. Sensors for series use are particularly suitable if a large number of measuring points are to be monitored. The low-cost sensor models, where the sensor model 627A01 belongs, can be integrated permanently into monitoring systems or used in conjunction with a portable data collector/analyzer for route-based monitoring. The accelerometer presented here, model 602D01, can be used in ambient temperatures up to 121 °C. If the operating conditions require it, this model is also available with EX approval or with SIL-2 declaration. All sensors are supplied with a 1-point calibration according to ISO 17025. — With through hole — Measuring range 50 g — Sensitivity 100 mV/g — Frequency range 0.5 ... 8,000 Hz — Single-point calibration at 100 Hz — 2-pin connection socket on the side Please contact us directly for an individual offer.