Air gas - Import export

Hot air heaters with gas operation from 23 to 34 kW The K gas hot air heaters are units that work completely autonomously, that is, they do not need heat dissipative elements, which reduces acquisition and installation costs. Its operation can be methane gas or propane gas and its operation is based on heating the air drawn in by the fans and driving the hot air inside the room to be heated. The main advantages over other heating systems are: - They do not take up space on the floor. - Reduction of acquisition and installation costs. - Very fast heating system. - Air diffusion can be direct or a network of ducts can be applied to channel the air into adjacent areas where the equipment has been installed. - Combustion efficiency greater than 90%.

Domestic and commercial heating with hot air boilers with natural gas or propane operation Our hot air boilers are ideal for domestic and commercial heating of premises from 370m3 to 840m3. Our hot air boilers can work with natural gas or propane gas and have a sealed combustion system, that is, the air used for combustion is from the outside and in this way the air from the room to be heated or from the air is not used. living place. Our hot air boilers can diffuse the hot air directly or a network of ducts can be applied to distribute the hot air in the different rooms of the house.

Eratec designs, manufactures and sells metal fibre gas burners. The Eratec metal fibre burner is an emitter with a refractory stainless steel combustion head on a Bekinit® knitted metal fibre radiating surface. The combustion head is equipped with an electronically controlled air/gas premixing system.

We use this vacuum degasser to clean all kinds of products before do the coating. This degas chamber is venting the gas,air and other impurities through putting in the heated N2. This vacuum degasser will greatly shorten the vacuum time, reduce the oxygen corrosion, protect the machine and prolong the life time of the equipment. It enhances the adhesion of the film in the products.

Heat transfer between a gaseous media and a liquid finned tube heat exchangers are often called air/water heat exchangers or gas/water heat exchangers. Heat transfer between a gas (for ex. air, steam) and a liquid (for ex. water, seawater, oil) takes place in the air-/water heat exchangers. Very often air/water heat exchangers are used as exhaust heat exchanger to gain the energy out of warm or hot exhaust fumes. Finned tube radiators can also be used as air heater, air cooler or condenser To improve the thermal output transfer from the gas to the liquid, fins made of well heat transferring materials are put on the tubes. The great increase of the thermal efficiency when applying fin tubes allows a substantial reduction in size and costs of such cooling equipment. The surface of such tubes is substantially increased and consequently less tubes are required compared with exchangers with plain tubes.

ZWP is one of the leading independent manufacturer in Germany for gears, pinions and rim gears. We supply already well-known manufacturers for gear boxes. We are looking forward getting intouch with you to have a conversation about possibilities for your supply. Sectors of our (international) customers are: Mining, Oil, Offshore, rail and ship transmissions, industrial transmissions and many more fields of applications. Overview about the capabilities for production: Gears internal and external toothed hardened and grinded Module 2 – 50 mm Diameter 100 – 2,000 mm Internal toothed rings / rim gears hardened and grinded Module up to 20 mm - more on request Diameter 100 to 1,800mm Pinions and shafts internal and external toothed hardened and grinded Module 1 – 50 mm Diameter 50 – 500 mm Length up to 1,500 mm Hardening and balancing inhouse possible Cooperation with companies for special manufacturing of gears and pinions etc We speak English.

ZWP is one of the leading independent manufacturer in Germany for gears, pinions and rim gears. We supply already well-known manufacturers for gear boxes. We are looking forward getting intouch with you to have a conversation about possibilities for your supply. Sectors of our (international) customers are: Mining, Oil, Offshore, rail and ship transmissions, industrial transmissions, and many more fields of applications. Overview about the capabilities for production: Gears internal and external toothed hardened and grinded Module 2 – 50 mm Diameter 100 – 2,000 mm Internal toothed rings / rim gears hardened and grinded Module up to 20 mm - more on request Diameter 100 to 1,800mm Pinions and shafts internal and external toothed hardened and grinded Module 1 – 50 mm Diameter 50 – 500 mm Length up to 1,500 mm Hardening and balancing inhouse possible Cooperation with companies for special manufacturing of gears and pinions etc We speak English.

Liquid gas

Poppe + Potthoff Maschinenbau GmbH supplies compressor units and pressure control systems of up to 400 bar for various gases. We offer ready-to-connect units to increase the existing pressure for pneumatic and hydraulic applications. In this way, the performance of existing systems can be increased flexibly and efficiently. Our compressor units are used wherever the existing system pressure is insufficient to implement specific applications. Of course, our systems are UL or CE compliant as required. In addition, we offer you service and support directly on-site.

The MGC101 system automatically performs zero, precision, span and multi-point calibrations using NO, NO2, SO2, CO, 03, hydrocarbons and other gases.

Pure air generator, capable of continuous delivery of up to 20 standard liters per minute (SLPM) of dry, contaminant-free air.

What you can expect from APROVIS oxidation and three-way catalytic converters: - Individual design for each specific application - Also special production for special applications - Short delivery times - Compliance with the limits over the warranty period - Use of soldered metal supports to withstand high thermal and mechanical loads - No telescoping of the catalytic converter elements

Media: hydraulic oil, water, air, gas, aggressive media

Special sealers ME 455/605 VAD with air suction system (max 80%) suitable for volume reduction and better preservation of products. The machine is equipped with a double sealing bar with a sealing width of 5 mm, an electric pedal drive and pneumatic cylinders, mobile nozzles for air intake, an adjustable timer for suction, sealing and cooling. The ME 4510/6010 VAG model with a ATM gas injection system is also available. This variant is equipped with a double sealing bar with a 10 mm sealing width, electric pedal drive, mobile nozzles for air intake and gas injection, adjustable timers for suction, intake, sealing and cooling.

Air-water / air-air heat exchanger as smooth tube heat exchanger up to 1,000 ° C Smooth tube heat exchanger as an air / water heat exchanger In the case of air-water heat exchangers (also called gas-water heat exchangers), a temperature exchange takes place between a gas (usually air) and a liquid. As a rule, the liquid medium flows inside the pipes, while the gaseous medium flows around the pipes outside the pipes. Smooth tube heat exchangers can cover various areas of application: heating, cooling and condensing as well as heat recovery. Smooth tube heat exchanger as air-to-air heat exchanger Smooth tube heat exchangers are also often used as air-to-air heat exchangers. In this application, a gas (e.g. exhaust air or exhaust gases) flows inside the pipes and a gas (e.g. fresh air) outside the pipes around the pipes.

Finned Tubular Heaters are the ideal solution for air or gas flow heating processes. The ribs enlarge the heat-releasing surface significantly. Basis of the finned tubular heaters are our 8.5 mm tubular heaters. The outer diameter of the fins is 28 mm. The elements can be delivered straight, U-shaped or circular (special design on request). Tubular heater as well as fins are made of stainless steel, the standard for the tube is 1.4828 (other materials possible as in chapter Round Tubular Heaters), the fins are normally made of 1.4301 (1.4571 on request).

Industrial desiccant dehumidifier TTR 2800 The stationary desiccant dehumidifier TTR 2800 impresses with a dehumidification performance of 376 kg / 24 h Humidity control at its best Even nearly 400 kilogrammes of dehumidification performance per day present no challenge for the TTR 2800 – not even in cold ambient conditions with low dew points. Therefore, the industrial desiccant dehumidifier is ideally suited for the most diverse air and gas dehumidification tasks in industrial, haulage or utility companies, for instance to secure products and production, for the value retention of machines, inventory and buildings through constant protection against corrosion, condensation or mould formation.

Electrical air heaters for air or process gas heating in pressureless systems: ·         Ventilation systems, Ex HVAC plants ·         Supply air heaters for machines ·         Heating of process gases ·         Heating of containers or heating chambers ATEX, IECEx, TR-CU and other international certificates

Dampers play a crucial role in the functionality of industrial ductwork as they are designed to control the flow of air or flue-gas within the ducts. The primary purpose of most dampers is to act as shut-off dampers. This means they are either fully open or fully closed depending on the operational requirements. However, some dampers are specifically installed to modulate the gas flow, allowing them to function in various partially open positions. The variability in damper functionality caters to different operating scenarios and provides flexibility in managing the flow of air or flue-gas through the duct system.

Increase performance of your pneumatic systems Powering pneumatic machines requires clean and conditioned air or gas. Our pneumatic filters are designed to work together with regulators and lubricators (FRL units), to offer outstanding performance and a lower-cost alternative to traditional sintered-metal filters. Specifically designed to provide an excellent combination of particulate filtration, air flow and back pressure performance, while complying with strength and aesthetic requirements, these single-component molded filters: Meet your filtration requirements – Optimized design meets filtration, airflow and pressure drop requirements. Reduce costs – Sintered polymer filters are more cost-effective than sintered metal. Improve machine longevity – Design is optimized for reliability, efficiency and longevity of pneumatic machinery. Features Work together with regulators and lubricators (FRL units) to deliver clean and conditioned compressed air or gas Strong and rigid for...

Industrial desiccant dehumidifier TTR 2000 The stationary desiccant dehumidifier TTR 2000 impresses with a dehumidification performance of 259 kg / 24 h Humidity control at its best Several hundred kilogrammes of dehumidification performance per day present no challenge for the TTR 2000 – not even in cold ambient conditions with low dew points. Therefore, the industrial desiccant dehumidifier is ideally suited for the most diverse air and gas dehumidification tasks in industrial, haulage or utility companies, for instance to secure products and production, for the value retention of machines, inventory and buildings through constant protection against corrosion, condensation or mould formation.

Flameproof mini line heaters ATEX Ex II 2 G Ex’d’ IIC T4-T6 nach EN60079-0 und EN60079-1 The Exheat range of flameproof mini line heaters consist of a screw plug or flanged type immersion heater mounted in a thermally insulated heating vessel. They are designed to efficiently transfer heat to a flowing medium (liquid, air or gas). All flameproof heaters are fully ATEX certified and designed for use in zone 1 & 2 hazardous areas, gas group IIC.

Liquids (for instance raw materials or end products) are stored in canisters, drums, IBC containers or storage tanks. Solids and bulk materials, on the other hand, are stored in bags, big bags, silos or various special containers. IFA Technology offers sound and safe handling for the storage of liquids, solids and bulk materials as well as suitable storage containers such as customised shelves, tank farms or silo systems. We check and control among other things the compatibility of the substances, the effect of environmental influences as well as the conformity with legal requirements. We ensure compliance with various regulations such as the German Water Resources Act (WHG) or Explosive Atmospheres Directive (ATEX) by means of temperature-controlled storage tanks and the blanketing of the relevant substances by means of nitrogen, dry air or gas displacement systems or their circulation via agitators or circulation.

Temperature control of gaseous and liquid media Flat tube heat exchangers are generally used as air / air or air / liquid heat exchangers. Flat tube heat exchangers are used where the (exhaust) air is polluted and the installation space is limited. In heat recovery in particular, there are numerous applications for flat tube heat exchangers as so-called exhaust gas / exhaust air heat exchangers. Little installation space and less pressure loss While the rows of tubes in smooth tube heat exchangers consist of round tubes, the rows of tubes in flat tube heat exchangers have a special profile (see illustration). This special tube profile offers advantages over the round profile in certain applications. Flat tube heat exchangers require less installation space than smooth tube heat exchangers with the same exchange area and are therefore also lighter.

Leak detector high detection sensitivity for pressurised piping and containers, e.g. on compressors, steel bottles, fittings, shut-off valves, breathing devices, oxyacetylene gas and inert-gas arc welding devices, Bunsen burners, valves, screw fittings of compressed-air lines etc. Suitable for compressed air, refrigerant, acetylene, butane, natural gas, carbon dioxide, gaseous oxygen, propane, town gas, nitrogen, hydrogen and, ammonia Suitable for checking the safety of systems with combustible gases and for avoiding financial losses through unrecognized leaks Advantages and benefits Frost-proof to -15°C Saves energy and warns of gas loss Contains corrosion protection inhibitors Tested by the DVGW in accordance with DIN EN 14291 Non-combustible Economical in use

Piping and hoses, for example steel bottles, compressors, breathing devices, oxyacetylene gas and inert-gas arc welding devices and burners Fittings, flanges, valves, screwed connections, soldered and welded connections of pressure gas systems and lines Suitable for compressed air, refrigerant, acetylene, butane, natural gas, carbon dioxide, gaseous oxygen, propane, town gas, nitrogen, hydrogen and, ammonia Advantages and benefits Acts non-corrosive Allows direct visual inspection of the leakage point through bubble formation Tested by the DVGW in accordance with DIN EN 14291 Suitable for spraying overhead

BORSIG offers optimum membrane solutions which help to minimise losses, recover valuable raw materials or products from exhaust air, and process gas flows. Our products for product recovery are: BORSIG Ethylene recovery unit PE BORSIG Hydrocarbon recovery unit BORSIG Propylene and nitrogen recovery unit BORSIG Ethylene recovery unit for EO/EG BORSIG Monomer recovery unit BORSIG Seal gas recovery unit Important products and applications include: - Ethylene monomer from polyethylene (HDPE, LLDPE, etc.), EO or VAM production - Propylene monomer from polypropylene production - Solvent (e.g. hexane) from slurry-type HDPE production - Alkane recovery in polyethylene production - 1.3 butadiene from synthetic rubber production - Vinyl chloride monomer (VCM) from PVC production - Fluoro and chlorohydrocarbons from any related processes - Seal gas recovery for rotating machinery

Flottweg Sedicanter separates solids from liquids. Its special feature: the solids consist of a sediment with properties ranging between soft and fluid. Typical applications of the Sedicanter are "soft products": ► Biomass, yeast and protein suspensions. ► Fermentation broths and UF retentate ► CIP cleaning liquids and coarse matter-free live sludge ► Fruit juice byproducts and plant-derived raw materials ► Soap separation from oil refining processes The special technical features of the Flottweg Sedicanter: ► Separation of extremely difficult-to-sediment solids by acceleration up to 10,000 gee. ► Hygienic design, thus usable for applications in biotechnology ► Flexibility with fluctuating composition of the feed product by the adjustable impeller ► Gas-tight operation is possible by sealing the separation space off from the ambient air using inert gas

Explosionproof/flameproof gas preheater EEx d -ATEX und IECEx zertifiziert In general a cooling down takes place at expansion of gases whilst a heating takes place at compression. Typical gases are carbon monoxide, natural gas and air. The temperature change, which occurs at expansion of gas or gas mixture from a high to low pressure i.e. after a gas pressure control is called Joule-Thomson effect. In order to prevent the effects of Joule-Thomson as icing or condensate separation, the gas will be heated up before expansion. The gas pre heaters are suitable for all kind of gaseous media (i.e. air, natural gas, technical gases, fuel gas) and low flow process applications, suitable for pressures up to 300 bar. The “Cast electric heaters” type flameproof electrical gas pre heaters are certified for use in zone 1 or 2 hazardous area, custom built to meet client specification. The gas pre heater consists of a process tube coil and an electrical heating bundle, casted in aluminium. The process gas flows through the tube coil and is heated by the aluminium block that provides the heat transfer. This indirect electric heating gives an accurate control of the process and eliminates pressure vessel design and associated costs.