wire cut

...The width and length of the wire mesh are either woven according to customer specifications or subsequently cut by us. Our maximum weaving width for many meshes is 3,000 mm. We also weave narrow meshes with a woven edge. The narrowest strip that we can cut from our fine mesh as roll goods in further processing is 10.0 mm wide. The roll length can also be chosen up to 300 linear meters. This is often limited by weight and transportability. The standard rolls are 25–50 m long.

... cut from wire. The length of the grain is equal to the diameter. Grain shapes of different roundness are produced through the subsequent rounding of the cylindrical raw material, rounded from G1 – G3. Cut wire shot has a particularly long service life and are known for low dust generation.

... high, 300 mm wide). It is designed just like the model 4500, but with larger dimensions. There are no restrictions on the length of the pieces to be cut, as long as they can be properly placed on the work table. The workpiece must be securely fastened to the work table, as the patented 30 m long diamond wire continuously unwinds and rewinds.

...Open wire heating elements are the best solution for air heating when used in fans. Because of our longlasting experience in this field, we can offer you a series construction in most cases. To use our open wire or coil heating elements in air, the installation of a cut-out is necessary (heat accumulation). The connection is done by a plug at the element (Faston 4,8 or 6,3) or by a cord set. Our...

...Rotor type wire straightening machine for the production of cuttosize wires up to Ø 6 mm (#3). Driven by digital electric servomotors. Max pulling speed 160 m/ min (525 ft/ min) High speed cutting unit with brushless (less than 0.1 sec) Web Teleassistance Available versions Fixed cut with adjustable backstop length for a maximum cutting precision (± 0.5 mm). Single strand:1 Ø 2÷6 mm (#3) Pulling speed:160 m/min (530 ft/min) Average power consumption:4 kWh...

...Features: • Constant power output per meter of heating cable • Processed from the roll • Can be cut to any length • Easy on-site assembly • Versatile use due to the high chemical resistance of the insulating and jacket material Teflon FEP Max. heating circuit length 75m 30 W/m Application examples: Frost protection heating, temperature maintenance, as well as heating of pipelines, containers...

...Depending on customer requirements and specifications, we cut, weld, taper, crimp, roll, splice, or braid your ropes. We produce both small and large series and develop the right product for your application. We also have a wide selection of accessories in stock. Feel free to call us; we look forward to assisting you!

...Cut Wire Axis to Length...

...WITH THIS MACHINE YOU WILL BE ABLE TO MAKE: Butter biscuits, almond doughs, curly biscuits, homemade biscuits, polvorones, perrunillas, mantecados, etc. •Uniform and fast production, avoiding punishing the dough or any alteration of its natural characteristics. •For medium and large productions, depending on the product and model. •Easy and quick change of moulds. •Intelligent production management by means of HMI panel, recipe programming. WIRE CUTTING AND MOULDS WITH A GREAT VARIETY OF SHAPES AND SIZES: For dense or hard doughs. ...

... also suitable for the food sector for the packaging of the bread. Operation: Place the coil with the open side facing the operator Insert the open-film blade between the two flaps Unroll the film to the desired length Lower the sealing bar and cut the bag Enter the product in the bag and make the welding of the side remained open. Sealing bar length:600 mm Film reel max. width:600 mm Adjustable sealing time:0~2 sec...

...Self-tapping threaded inserts for the manufacture of high-strength screw connections, resistant to wear and vibrations in materials with low shear strength, such as aluminum and aluminum alloys, brass, bronze, cast iron, duroplastics, and thermoplastics. The threaded inserts have a conical lower end and a cutting slot. They cut their own thread when screwed into a hole to ensure a secure and...

...Shear-wire stripper to cut Kevlar¨ and to strip optic fibres. Fixed at ¯ 0.18mm. Length 148mm...

...Cutting the labels without cutting the support There are two processes depending on what is being cut. The cutting of the shape with a cutting wire connected to a fixture plate that acts as an anvil. All our plates are made of treated steel, ground, and referenced for perfect flatness (0 ± 0.001). Grinding wheels with cylindrical cutting counterpart.

...The new EDM high-performance wire with patented TRIMPAC® technology. The new coating technology TRIMPAC® has been developed from the strengths of the wire generations cobracut®, broncocut®, and topas®. The result is the gapstar® ONE. Features: - A revolution in speed and precision - Significant increase in feed rate during the main cut and finish cut without technological adjustments...

...-plated Technical Data: Motor power: 5.5 kW (7.5 HP) at 1400 RPM Cutting discs*: diameter 356 mm Cutting capacity: diameter 105 mm Table travel (feed cut): 220 mm Max. height of the cutting disc (356 mm) above the table: 110 mm X travel: 120 mm Cutting table: 410 x 310 mm (W x D) gray cast iron, chemically nickel-plated, 12 mm T-slots Power supply: 400 V / 50 Hz / 3 phases Safety features: Electromechanical locking of the cover, emergency stop switch, CE compliant Weight: 260 kg Dimensions: 1540 x 1010 x 700 mm (W x D x H) or 1540 x 1010 x 1020 mm (W x D x H, cover open)...

...Available in nominal diameter Ø in mm from 0.44 up to and including 1.54 mm. Available as bulk material or pre-cut.

...Cut and stripped cables soldered to the pcb. Short wire processing with our Komax Kappa.

... adjusted to the desired dimensions during application is technically advantageous, and the cost-effectiveness of being frameless is financially beneficial, although it cannot be said that it complies with the machine safety regulations in every respect. For this type of safety panels, the ordering process takes less time, as no precise measurements are required for the application. System height: 1000 / 1200 / 1500 / 2000 mm / 2500 mm Panel height: 1000 / 1200 / 1500 / 2000 mm Panel width: 2500 mm Wire thickness: ø 4.5 mm Mesh size: 50*50 mm...

...The WPC is an integrated solution to produce wires for switch cabinets: it marks them and crimps the corresponding wire end ferrule. The WPC loads an EPLAN or other CAE file and produces all wires within this list step by step. Cross-sections from 0.5 mm² to 2.5 mm² are supported. For each item in this list, the wire is cut to length sequentially with the help of the multi feeder Z+F EVOFEED®...

...• For securing rebar for reinforced concrete with splice wire from a roll • Twist and cut wires in a single operation quickly, reliably, and economically • The edges are additionally induction hardened • Plastic-coated handles • Made of tool steel, forged and oil-hardened Length in millimeters: 250 Weight in grams: 395...

...Rubber Grommets are a highly popular cable management tool that offers the ability to easily group and bundle cables/wires. Along with their management properties, they also provide high levels of protection for the wire, allowing it to pass through a sharp piece of metal or panel. Available in many different options, including Open, Closed, Cut To Fit, or Quick Fitting, we have an option for...

...Joining tubes can be used to create a hybrid join between a full strand weave and the use of joining clips. A single strand is cut into smaller single space sections, which are woven into the belt and joined together by crimping a stainless steel joining tube onto the adjacent wire sections. This method maintains the belt strength of a full strand weave while eliminating the distortion that occurs during the weaving process. It is important to consider whether joining tubes could mark product or have hygiene implications when choosing this method. material:stainless steel...

...Wire mesh shot blasting systems are highly versatile. The ability to blast workpieces from both the top and bottom simultaneously significantly expands the range of workpieces that can be processed. Wire mesh shot blasting systems are used, for example, for deburring, descaling, and cleaning cast and laser-cut parts. Our standard wire mesh shot blasting system program includes throughput widths...

...Stainless steel wire is an important material used in a variety of applications, including in industry, commerce, and residential areas. EDER offers high-quality stainless steel wire known for its excellent strength, flexibility, and corrosion resistance. Diameter: 0.5 mm 1 mm 1.5 mm 2 mm 3 mm 4 mm 5 mm Lengths: Available in coils or cut to length EDER's stainless steel wire is perfect for use...

...Fencing systems made of double wire mesh panels with a mesh size of 50 x 200mm or 100 x 200mm The vertical bars are approximately 6mm thick, while the horizontal bars are double-guided and about 8mm thick. We can also offer lighter variants. The mesh panels have a length of 250cm and can be cut to size with a height ranging from 63 to 243cm. Strong square tubes are used as posts. The double wire...

...Seal wire on spool or cut to length. Seal wire on spool, galvanized iron in various thicknesses.

... can choose from premium steel, spring or stainless steel, as well as non-ferrous metals, which we process according to your individual requirements. The wire, with a diameter ranging from 0.5 to 5.0 mm, can be laser cut, stamped, or embossed, and bending, grinding, and assembly are also part of our manufacturing techniques. When it comes to processing the surfaces of your custom parts, prototypes, or small and large series, you can choose between bluing, galvanizing, painting, as well as tumbling and phosphating.

...Non-Grain Oriented Electrical Steel (NKO) is a specially manufactured steel to achieve certain magnetic properties. It ensures low power loss, core loss and high permeability. NGO is the first choice for manufacturing lamination stacks for stator and rotor of electric motors. The sheets are laminated and cut into the final shape through various processes before winding. Punching, laser cutting and wire EDM are some of the processes used to achieve the final shape.

... barriers. Application temperature: up to 550°C Application limit temperature: approx. 600°C Variants: made from smooth or specially air-textured yarns Coating: PU-Alufix, F120 Reinforcements: V4A wire reinforcement in warp and weft threads Material thickness: 0.8 - 2.0 mm Standard width: 1000, 1200, and 1600 mm Format: roll goods, blankets, cut pieces, stamped parts, custom configurations...

... temperature, Higher light conversion, Better performance in reduced irradiance conditions, Manufactured & tested at European standards. ◇Minimum Order Quantity (MOQ): 1 container, ◇Payment Terms: 30% advance payment against order and 70% against Bill of Lading or respectively Airway Bill, ◇Terms of delivery: EXW warehouse Europe - CIF worldwide - FOB Europe - Delivery within 2 weeks from Europe after receipt of payment, ◇Methods of payment: SEPA transfer and Wire transfer, ◇Payment currency: EUR...