measurement and control

...FIFO disc magazine and control measurement device...

...DWS static allows for the collection of all shipping cost-relevant data at the push of a button. The system consists of the proven volume measurement system VMS 510/20, a robust static scale, and a barcode scanner for capturing code information – all integrated into a stable mechanism. The system is ready for operation within minutes and can be calibrated according to applicable standards...

...Eco-designed, ultra-compact, smart & connected continuous gas analyzer, for emission or process gas monitoring. Perfectly suited to control SO2 removal efficiency in processes using Flue-gas desulfurization FGD / DeSOx systems. Measurement range:0-100 / 0-1000 mg/m3 user programmable; 0-35 / 0-1500 ppm user programmable Minimum detectable limit (2σ):0.2 ppm Noise (σ):0.1 ppm Response time (0-90 %):5 – 40 sec (programmable) Zero drift:< 1 ppm / 7 days Span drift:< 1% / 7 days Linearity:± 1 %...

... All configuration data editable High measurement accuracy Space-saving in the control cabinet Variable adjustable cutoff frequencies Linearity deviation: < 0.005 % of full scale. Measurement rate: 14400 measurements/s. Sensor type: DMS / potentiometer / DC/DC/incremental sensors Interfaces: screw terminals Sensor supply - DMS full bridge: 2.5 V / 5 V / 10 V configurable, short-circuit proof Sensor supply - potentiometer: 5 V Protection class: IP20 Supply voltage: 11 ... 30 V DC. Galvanic isolation, reverse polarity protection, overvoltage protection...

... Measurement accuracy: according to ISO/IEC 15426-1 Measurement width: 75 mm including light field zones Aperture: 6, 8, 10 mil Measurement accuracy: +/-5 average; +/-10 extreme values Power supply: primary 110-240 V~ Dimensions (L x W x H): 222 x 85 x 95 mm Weight: 660 g...

... measurement method for layer thickness on elastomers. Light microscopes have reached their limits at a few micrometers. The methods applied to coated metal parts do not yield acceptable results on elastomer substrates. Only cuts measured with electron microscopes or cross-sections of embedded samples provide usable results.

...The CSN® type RCVoltage Dividers consist of a proven reliable and high accuracy resistivecapacitive voltage divider. These are used for voltage measurement for control and protection systems in HVDC links and research institutes. The base for our Voltage Dividers are metal wire resistor webs that have been embedded in epoxy resin under vacuum. In this way, optimal protection against external...

... effective pressure principle operates without rotating parts. The sensors can be visualized via a protemp control system or connected to a PLC, depending on the model. A completely contactless flow measurement based on the ultrasonic principle is available with the proflow ultrasonic. Robust flow measurement in the consumer return PT 1,000 temperature measurement in the consumer return 6 x...

...Are you looking to enhance the reliability of your equipment or production? Would you like to improve the quality and consistency of your manufacturing or assembly processes? SMI is your go-to partner in the Grand Est region to assist you with all your projects involving the selection, integration, or creation and implementation of measurement and control systems. We offer detection and...

...Hybrid Technology – Smart Assembly Solutions The YOKOTA electric system wrenches with integrated torque transducer and angle sensor offer a large reduction of energy consumption, a high degree of accuracy and fantastic work efficiency. Torque transducer and angle sensor located directly at the front of the main shaft, giving the best accuracy of measurement. Faulty tightening detection...

... being designed and produced in accordance to the highest quality standards. There are two premium components, constructed with the IP54 rating. The item comes with an easy to lean glass surface made of high scratch-resistant. The capacitive touch screen control panel and the high resolution color display for simultaneous indication of two measured values is another major advantage, while the quick and non-destructive determination of near-surface moisture distribution is another major advantage. Measured material:for solids Technology:dielectric Other characteristics:hand-held,wireless...

...Measurement of steam Much unused energy is wasted through the exhaust air during drying processes without appropriate control. The Ecomat AML optimises the heating energy required by monitoring charging of the exhaust air with water steam and controls this factor through the fan speed or the exhaust air vent control.

... optimize the measurement uncertainty of measurement setups. In the training, we focus on: Mathematical Fundamentals; Definitions and terms; Application of the GUM method; Creation of measurement uncertainty budgets; Calculation of measurement uncertainty; Analysis and critical appraisal. You can design the training according to your wishes! Holding a workshop in which you actively contribute your problems has also proven to be a good idea. We are happy to respond to your individual questions and concerns.

... over the last few years regarding measurement accuracy and reliability of temperature measurements has meant that many equipment operators must reconsider the suitability and performance capacity of their temperature measurement equipment. Resistant thermometers can be used between -200 °C and +850 °C. An important common property is that their output parameters are available in the form of electric signals that can be relatively easily transferred to measurement and control instruments for processing, storage and display.

...Component acceptance using measuring arm and laser tracker in special machine construction: MIP3D supports a client from the special machine construction sector with its mobile measuring devices during a component acceptance process. By combining a laser tracker and measuring arm, all required geometries can be easily reached, measured, and documented in a digital measurement report. The speed and flexibility of our service leave both the client and supplier highly satisfied.

...Often, the main problem for molding industries is not reaching the necessary temperatures for their processes, but maintaining them over time. This is where temperature control units come in handy, which not only heat the fluids required for the job but are also capable of self-regulating afterwards. This is how the FTT DC water temperature regulators operate, which incorporate direct cooling to...

... implementation, as they no longer have to deal with time-consuming calibration. • High profile speed of 14,000 profiles/s and up to 28 million points/s • High resolution of up to 0.3 µ • Compact form factor • X measurement range of 10-1022 mm • Z measurement range (height) of 5-878 mm • Laser wavelength blue 405/450 nm, red 650 nm The new Q5 laser scanners also incorporate additional useful product features, such as the possibility of a master-slave configuration for multi-scanner operation and more.

...High-precision incremental measuring probe with magnetic operating principle Extremely insensitive to contaminants such as oil mist, moisture, and dust Wave groove bearing of the measuring pin for long service life Perfectly suited for automated measurement data acquisition in measuring devices, assembly, and manufacturing systems Measuring range: 12mm Accuracy: 1µm (p-p) / 1.5µm (p-p) Max...

... (Motor Under Test) at a low speed from 1 to 10 rpm (respectively 8 rpm for CTS 103 and CTS 104), while acquiring its cogging torque related to angle position. The torque measurement covers a range up to 1 N∙m (depending on the selected torque sensor) with an accuracy of ± 0.1 mN∙m (for TS 100 – 50 mN∙m and TS 101 – 100 mN∙m). The executable software controls the system and displays acquired data. It...

...The dew point hygrometer MTR 5.5 allows, in addition to its direct use as a measuring device, the optional use of available analog and digital measurement signal outputs, alarm functions, switching outputs, and data logger functions for monitoring climate values or integration into monitoring and control systems. An option is available for a device version with an integrated battery, which...

... a plastic shaft is optimal for use in aquariums, garden ponds, and for monitoring garden soils. It provides reliable measurement results for precise pH control. Robust plastic construction: The plastic shaft of the electrode is sturdy and resistant to the specific conditions found in aquariums, garden ponds, and garden soils. This ensures a long lifespan and reliable performance.

...Pfeiffer Vacuum has expanded its product portfolio for total pressure measurement and has introduced a new family of measuring devices. In addition to the existing lines DigiLine, ActiveLine, and ModulLine, we now offer new measuring devices from the CenterLine series, which are compatible with the existing active transmitters from other manufacturers*.

Imeta has been producing "Rolline" and "Mandrini" for "Macchine Aggraffatrici" since 1963. We are a workshop for the revision and restoration of "macchine aggraffatrici". Cutting-edge technology. Customized products. Highly specialized in the design and production of products for "aggraffatura", we currently possess the construction drawings of the most widely used "mandrini" and "rolline" in the ...

...Housing for satellite positioning devices TC designed and constructed a weatherresistant housing in a very small batch for highly sensitive satellite positioning measuring devices. Do you already have an idea of what we could do for you?

... (transmissions, axles, etc.) Automotive Component Testing Noise and vibration level measurements special systems ​ EoL testing systems are complex systems that generally operate automatically and include a range of sensors, data acquisition devices and testing equipment. Test procedures can be prepared in the form of predefined scenarios by the development team and stored in a database. Different scenarios can be prepared for different test conditions (high speed, low speed, long term, short term, etc.) and then called from the database.

...Customized Solution The mobile testing device may be mounted directly on the wheel nuts on any wheel on the car. The height and tilt adjustment allows optimal orientation at the wheel. Additionally, it is still supported by three proximity sensors. The evaluation and control of the testing device accepts a laptop. For easy transport, the device can be disassembled in a few steps. Curve recording and analysis via notebook. The complete unit is height adjustable via a scissors system. This can also be adapted to different shaft height.

...For continuous level and temperature measurement of water and wastewater, BD/SENSORS has developed the LMK 307T. The advantage: Simultaneous measurement of level and temperature with separate, independent signal amplification. Maintenance and wiring efforts are significantly reduced. In addition to the classic signal processing of the level, there is an additional signal circuit independent of...

... The Innolog™ and Innocheck™ products, designed by Kelvin Solutions, are indispensable tools for monitoring the temperature of food products throughout the cold chain and can be integrated into the HACCP self-control system.

... • Integrated lightning protection circuit • Bidirectional flow measurement • Quick response to flow/collection changes Type: Electromagnetic flowmeter to be inserted between flanges Diameter: DN15 to DN300 Measurement range: 0.05 to 15 m/s Protection: IP65, IP67, IP68 Sensor housing: Carbon steel; Stainless steel Coating: PTFE; Ebonite; F46 (DN15-DN300); PFA (DN15-DN300); Polyurethane (DN15-DN750) Electrodes: Stainless steel 316L, HB, HC, titanium, tantalum, platinum-iridium, tungsten carbide Measuring sleeve: Stainless steel 304; Stainless steel 316...

...The control elements are equipped with dovetail guides ("hard-slide" coating) or cross roller guides and are rack & pinion, micrometer or worm driven. They have minimized backlash and a straightness accuracy within a few microns. The control elements can be equipped with one or two knobs or without any knob. Multi-axle systems can be built up using the control elements and corresponding connection elements. An intermediate plate (B40-RP) is required to attach the tube elements.