surface adhesion improvement

...Plansee produces materials for wear protection layers, adhesion layers, decorative or DLC coatings. Customized compositions are offered for advanced hard coatings with optimized mechanical and tribological properties. Additionally, the following enhanced properties are possible: improvement of thermal and chemical stability, adding functional properties such as self-lubrication, self-hardening...

... mixing water, (approx. 0.5 litres per 25kg bag of product) in the single component version, allows further improvement in terms of adhesion, hold, impermeability, workability, modelling and deformation capacity. In the case of use of the product in the two-component version, pour component B (liquid) into the mixer, gradually adding component A (powder) and mixing until the lumps are completely...

... this method, surface properties are improved without using any chemicals and without changing the main properties of the material, thus increasing the adhesion, painting, adhesion and antiseptic properties of the treated material. The most important effect of corona treatment is to change the surface properties of the plastic or film material. In particular, it is to increase the surface energy of...

... plasma is a proven technique for controlled ultra-fine cleaning, improvement of adhesion (activation and etching) and coating of thin layers on substrate surfaces. Plasma is generated by applying high-frequency voltage in the vacuum chamber. In the process, the process gas introduced there is ionised. Fields of application: VOC-free cleaning of organic residues. Activation before painting...

... both sides in varying degrees. This can be a very significant improvement in the adhesion of coatings to be achieved. POLI BOND can in the film thicknesses 19µ - 350µ are delivered.Different printings require different surfaces. In addition to highly transparent or colored opaque base films we offer here at various coatings that allow easy and quick editing. Seal foils are coated films, the above-defined temperature ranges enable an activation of the coating so as to allow bonding of different products. POLIFIBRA films offers solutions for different temperature ranges and applications.

...The aim of the activation process is to alter the nature of a surface or its energy. More often than not, this allows the wettability of a surface to be increased (by adding polarity) or encouraging the adhesion of a coating (paintwork, ink, glue, varnish). Plasma activation is a simple process that allows a wide range of improvements. Plasma pre-treatment allows, in one single, simple and cheap stage, a significant improvement to the surface to be achieved.

...Forging lubricant for aluminium and non-ferrous metal Temperature Range 160 °C to 400 °C Properties and Advantages • promotes the metal flow during forming process resulting in optimal form filling and accurate, precise parts • perfect release • much cleaner forgings, hardly any residues • reduced cleaning effort • high surface quality • improvement of tool die life due to adhesion of protective graphites • various modifications available e. g. Graphitex® CR 25-9/14...

...Colors: Anthracite, Silver Gray, Natural White - Acoustic panel made of sheep wool with adhesive coating - For permanent adhesion - Processing: cutting, drilling, bending; can be laid almost seamlessly - Improvement of reverberation time: Alpha-w 0.35 - Regulation of room climate (humidity) - Filtration of harmful substances (formaldehyde) from the indoor air - Allergy-free, moth-protected...

...High-density underlayment made of latex insulation foam with a mineral sand mixture incl. self-adhesive layer. Density approx. 1,000 kg/m³. The adhesion to the surface layer significantly reduces footfall noise. The absolute top choice if you want the best impact sound and walking sound improvement.

Flame treatment systems for pre-treating plastic and metal surfaces Distance Adhesion improvement for printing, bonding, laminating, etc. Distance Working widths from 25 to 10,000 mm Distance Wide selection of different burners Distance Special designs and automation Choosing the right burner is a crucial factor for pre-treatments. The burners differ in heat output and in the geometry of the flames produced. The active area of the flame should be selected to optimally cover the geometry of the substrate to be treated. Test inks for measuring surface energy...

... AF-12 and AF-8. Quimiasfalt designs mixtures tailored to the requirements of each client. Meanwhile, Microasfalt manufactures and also executes rehabilitation works for roads and highways, using its own products. Cold micro-aggregates, mainly MICROF 5, MICROF 8, or bituminous slurries, primarily of types LB-3, LB-2, and LB-4. With these techniques, Microasfalt specializes in the surface rehabilitation of road pavements, achieving an extension of their useful life and an improvement in the CRT, which leads to enhanced road safety.

As an aluminum refinisher, we specialize in the surface treatment of precision components for electronics, medical technology, machinery and equipment construction, as well as exhibition and shop fitting. We are committed to ensuring short delivery times through the fastest possible service. Adherence to deadlines and quotes is a matter of course for us. Our range of services Chemical pre-treatment for corrosion protection and adhesion improvement (3-zone pre-treatment system with degreasing and zirconium nano-coating) Coating (electrostatic in a manual booth) Curing oven...

... time. If you need help, we are quick to provide a solution for you! We offer contract fluorination as a service for you. With this method, you can improve the surface quality of your workpieces. This often allows for more cost-effective product solutions without the need for other materials or processing methods that require high effort. Improvement of surfaces Better adhesion More...

... DOES PVD COATING MEAN? PVD allows you to offer your products greater resistance, increased durability, and superior quality. It is an extremely thin ceramic coating with high adhesion, deposited in a vacuum chamber by highly ionized plasma. It has a hardness more than double that of hard chrome, with a low coefficient of friction, protecting against chemical and thermal attacks, and is resistant to wear from adhesion and abrasion. All of this in an eco-friendly process!

... through titanium coating, as well as creating barrier layers for plastics and other materials in general, enhancing adhesion behavior, and cleaning surfaces. Titanium coating of plastic materials, nanotechnology coatings, surface optimization through metallic coatings, plasma treatment, biocompatible surfaces for surgical implants and devices, improvement of adhesion behavior, nanotechnology surface cleaning.