... agents, care and disinfection products. Centrifugal pump with axial impeller in a compact design Direct connection to the IBC floor drain via a standard threaded connection (S60 x 6) Explosion-proof versions for applications in Ex zones (zones 1 and 2), including a non-return valve Two-piece pump that is easy to disassemble with clamp connections according to DIN 32676 No suction hose is required, significantly reducing product release during disconnection.
Italy, Poggio Torriana
...Abrasive blasting chamber with anti-wear coating; Automatic door; Turbines; Abrasive dispensing valves; Bucket elevator; Pneumatic abrasive cleaning separator; Electrical panel; Onboard electrical system; Pneumatic system; Photoelectric barrier for automatic doors; 6 hooks with a capacity of 500kg Turbine RPM: 2925 Turbine motor power: 7.5 Usable passage for introducing parts: 900x1400 Dust extraction unit power: 5.5 Required suction: approx. 5000 Total installed power: 18.5 Hook capacity (no. 6): 500...
Italy, Goito
... support must be healthy, clean, rough, without loose parts or dust (suction under strong depression with suitable equipment for all dust and debris) with tensile strength > 1 N/mm2. Wash the surface with pressurized water and saturate the substrate with water before applying, eliminating any excess water on the surface before applying the grout. Approximately 21 kilograms/square metre of Floor Q SFR per centimetre of thickness to be achieved (approximately 2100 kilograms per cubic metre). Packaging: 25 kg bag Unit of Measure: €/kg...
...the sealing lip closes off the path to the tool's interior, ensuring maximum safety against the suction of emulsion during the cooling phase. No friction-related wear on the tool spindle (50 percent of all service cases). In case of service: Affordable sealing replacement instead of expensive spindle replacement.
Austria, Aurolzmünster
... COMPONENTS radial fans makes it possible to achieve large volumetric flows even with unilateral bearings (i.e. single-flow systems). Bearings can be provided on both sides if requested by the customer, and this configuration is implemented as standard above a critical impeller mass. With their flow-optimized suction pockets, double-flow radial fans make it possible to create efficient designs for...
Switzerland, Baar
...In cases where the birthing process requires vacuum assistance, this mobile suction unit can be an effective solution. Medela offers a complete system that includes a secretion aspirator with all necessary components and a wide range of suction cups. • The obstetrician appreciates the active vacuum, as this can reduce the chances of involuntary detachment. • Thanks to the wide range of rigid and...
...Single-impeller pumps (JAP 80-100 M-T) or double-impeller pumps (JAP 150-200-300 M-T) with axial suction inlet and radial discharge outlet directed upwards. The distinctive feature of this model is the high suction depth achievable through proper installation of the ejector body. Therefore, it is indicated in all cases where there is a need to suction at depths ranging from 10 m to 50 m. Flow...
Italy, Santarcangelo Di Romagna (rn)
... all common types of decorative plates for 3 modules (not supplied with the socket) that you should already have available by removing them from the faulty socket. The built-in aspirating sockets are installed in universal-sized wall boxes in 95% of cases. The only exceptions are installations made before the 1990s. Outdoor and special aspirating sockets, on the other hand, can be replaced...
Austria, Sankt Pantaleon
...The high pressure of Air Power PRO results in a suction strength similar to that of a 1 m high water column – even the smallest particles can be lifted from inaccessible component parts. Components not exposed to expansion pressure No direct contact with gas No whirling or extrusion of particles PICK UP protective tube – abrasion-free material Note: Please note: To use the Mini Vacuum for sensor cleaning, use the enclosed PickUp protective tube (SC-4050-3).
Austria, Eugendorf
...In some tank systems, the distance from the tank to the burner is so great that the burner pump cannot draw in enough heating oil on its own. In such cases, suction or pressure storage units are installed to avoid burner malfunctions. We calculate the suction or pressure capacity, organize, and install the unit. We naturally offer a corresponding maintenance contract for the respective unit. For detailed questions, our competent team is at your disposal.
Germany, Wuppertal
... bulk material lies on the "thread" and is conveyed in the desired direction by continuous rotation • The size of the conveyors depends on the type of bulk material and chips • Horizontal, vertical or inclined material transport Typical use cases: • Removal of chips from chip bunkers • Suction locks of pneumatic suction systems or return pump stations • Intermediate transport of short and long...
...Positioned behind the workstation - Equipped with suction slots for optimal air flow - Designed for capturing light dust, aerosols, gases, and smoke When contaminated air spreads widely throughout the workspace, localized capture of pollutants is insufficient. In such cases, it is necessary to expand the capture radius and collect this air over a larger area. This is where extraction walls...
... glass railings. Our window installers give you the opportunity to unleash your imagination to bring your projects to life. For this, we offer a vast selection of glass (flat, frosted, opaque, high resistance, insulating...). You simply need to choose your glass, and our professional teams will then install it on your chosen support. We can also offer retailers custom display cases.
... plant in sheets lying on pallets. A suction bar separates the papers from the stack and pulls them on to a laying conveyor. A suction carriage delivers the board made from wood-based material. The laying conveyor conveys the batch from laying station to laying station / conveys the assembled batch to the facility core. The batch is statically charged in order to secure the papers on the carrier board for continued transport. Advantages The individual layout of the batch layer is based on coordinated standard modules. ...
France, Ancenis Cédex
... items to be transported. Specializing for 20 years in lifting and handling solutions, AMIO Levage provides vacuum handling devices with the design of suction cup spreaders, magnetic handling with the design of magnet spreaders, and not to forget the mechanical spreader that can be configured in multiple ways. The AMIO Levage Suction Cup Spreader It comes in three technical solutions: The first is made using a tube that exclusively ensures lifting.
Netherlands, Vlaardingen
...The HECHT Containment Drum Discharger CFE-L with tipping mechanism is used for the low-contamination discharge of drums with an inner lining up to OEB5. Discharging drums using a suction lance is particularly suitable in cases of limited space or for controlled discharge of the product based on weight. The ergonomic operation of our drum discharger won the POWTECH Technology Award in 2016.
... pulses. The dust is collected in a dust collection container. The electrical control unit is located in a control cabinet on the outside of the device. Additional equipment such as a filling device, a cyclone pre-separator, or a differential pressure-dependent compressed air cleaning system is also possible. A wide range of performance levels with different filter areas facilitates planning for various application cases.
... towards the center and is continuously suctioned off. The SOS series, with its full equipment, is ideally suited for the majority of applications and challenging tasks. The integrated oscillation systems for film/big bag tightening and suction head enable the discharge of free-flowing to highly bridging materials. Due to its column design, the OKTOMAT® SOS is particularly space-saving in width, and the...
Belgium, Bruxelles
Mecatelier is a company based in Hainaut, Belgium, specializing in the manufacturing and marketing of industrial surface treatment equipment, particularly painting booths for all sectors of activity. Mecatelier's products are committed to providing its clients with ideal and efficient working conditions. We guarantee custom booths, specifically optimized for your project. Our product range inclu...
Germany, Klipphausen
30 years of professional solutions "around paint" - 30 years of partnership for success. TOPLAC is the competent partner for vehicle and industrial paints, paint accessories, vehicle and boat care, as well as for the development and construction of individual paint systems. This year, we are celebrating a special anniversary - 25 years of TOPLAC! The TOPLAC team sets high goals - both for its own ...
United Kingdom, Poznan
Anti-Gravity Phone Cases Stick To Most Flat Surfaces Thanks To Nano-Suction Material On The Back Of The Case. Imagine million tiny suction cups that do the work so you can have hands free selfies, recipes at your fingertips or even netflix in the bath tub, up to your imagination.
... function to extract any objects that can pass through the strainer located at the end of the suction hose, without the need for any further action such as airing during operation, thus they are capable of draining water in all cases of flooding. As a result, high-pressure water can be provided by Kube Pump. Kube Pumps are also suitable for environments where fire brigade trucks are not available or...
France, Bondoufle
... particularly useful for the extraction of fumes, dust, or wood chips related to your activity. Our design office studies your project and offers you the best solutions for suction, filtration, or industrial dust extraction, taking into account process constraints and environmental constraints, all while adhering to current regulations. We indeed aim to limit the emission rate of our installations and thus...
France, Saint Benoit
Founded in 2021, AMBC (Aspiration, Machines à bois, Concept) is now positioned as a specialist in industrial dust extraction for wood chips, piping, and heating solutions. More specifically, we specialize in the design, manufacture, and installation of air conditioning and ventilation solutions for industrial buildings in mainland France. With several years of experience, we are committed to prov...
Germany, Luckenwalde
Proton Maschinenbau, with 41 years of experience, is one of the leading manufacturers of sandblasting, wet and powder coating systems, turnkey paint shops, and surface treatment technologies, exporting to over 30 countries. In addition to wet paint and powder coating systems produced under the brands ELBOY and PROTON, Proton has also manufactured industrial ovens in various types, chemical surfac...
... sludge suction vehicle into service in the early 1960s. The technology was successfully further developed, and today the majority of all canals are cleaned using the efficient and pipe-friendly high-pressure flushing technology. Continuous improvements are being implemented; special flushing nozzles enhance the cleaning results and also allow for the removal of the most stubborn deposits. Root...
Germany, Nürnberg
... and the pressure and suction side connection options lead to optimized installation possibilities. The quiet and vibration-free operation makes extensive soundproofing and foundation measures unnecessary in most cases. With volume flows ranging from 5 to 2150 m3/h and pressure differences of up to 750 mbar, the side channel blowers and vacuum pumps are ideally suited for the following...
France, Dompierre Les Ormes
Since 2009, the French manufacturer MCI has built a reputation through a large number of diverse and varied projects. MCI continues its commitment to developing its tools and skills. As a major player in the field of surface treatment, MCI is equipped to meet your needs for any type of project, thanks to the expertise of its staff and its fleet of modern and efficient machines. MCI is, and will r...
The company, headquartered in Lörrach, Germany, is one of the world leaders in the manufacturing of machines for machining steel, aluminum, and other non-ferrous metals. In addition to circular saws, band saws, and drills, KALTENBACH's product range includes the most modern installations for machining steel profiles and sheets, punching/shearing centers, and shot blasting and painting lines. These...
France, Sargé
BRETEAULT is a leader in the distribution of automotive and industrial paint in the greater west of France. We distribute body paints for cars, heavy trucks, motorcycles; all complementary and consumable products, hygiene and safety items, washing and renovation products; all equipment intended for bodywork; industrial paint for all surfaces: steel, galvanized, zinc, aluminum, glass, plastic, wood...
Popular countries for this search term

The europages app is here!

Use our improved supplier search or create inquiries on the go with the new europages app.

Download in the App Store

App StoreGoogle Play