heating system valves Germany

...The controller is a fieldbus device for the control of up to 7 power modules from the modular heating System from Kendrion, which are directly connected via the module bus. In addition to system monitoring, the controller can also control or regulate the individual output channels of all power modules. Actual temperature values can be delivered directly via CAN fieldbus or provided by a higher...

...For heating system, made by casting and machining, material annealed cast iron KTH35010, sizes Ø46mm x 15mm, weight 0,1kg, annual demand 30.000pcs...

...Elastic balls are primarily used as closures in valves and pumps, in pipelines and heating systems, as pigs for pipe cleaning, or as cleaning balls in screening systems. Valves are among the most well-known shut-off devices and prevent unwanted backflow of gases, liquids, or granular materials and dust. In the cage of ball valves, the freely movable elastic ball is lifted from the valve seat by...

... is done using a compressed air pulse via solenoid valves. This method of cleaning is very economical, as it is demand-dependent based on differential pressure measurement. The installation and removal of the filter bags are carried out without tools from a mounting platform. Systems that operate in frost-prone areas are equipped with valve heating and an additional cover for the solenoid valves. The required piping layout is designed individually. Hellmich exclusively uses branded components for electronic or electrical assemblies...

...Connections upwards and downwards are possible in the same distributor. Distributor connection block with 1 ½" male thread and 1" female thread, plus four additional ½" drill holes for e.g. air vents, filling and draining valves, thermometer. Distributor connection can be from the right or left. Branch fittings ¾" male thread Eurocone for plastic, copper/soft steel, or multilayer composite pipes. Delivery of individual parts as a modular system or as a fully assembled and pressure-tested ready distributor with or without accessories.

... thermostat valves and control mechanisms due to contaminated cooling components and control parts, high engine temperatures caused by barriers to heat exchange. Application: Add the contents of the can to the coolant. Turn on the heating. Let the engine run for about 30 minutes at operating temperature. Drain the coolant and thoroughly flush the system. Fill in new coolant according to operating instructions. Container: Plastic drum Country of Origin: Germany Content: 200 liters...

...Thermostatic valves - i.e. the temperature controls on the heating system - are found in just about every home. In the head of a thermostatic valve there is a metal bellows, a corrugated tube that expands according to the room air temperature. For these metal bellows, the manufacturer needed deep-drawn, very long and thin-walled sleeves. The challenge: the sleeves must be matched to the...

... or double-acting, have proven themselves over the years. However, process air in the industry is expensive. Energy efficiency is therefore the topic of the day. As a manufacturer of valves and drives, EBRO can customize individual product components according to customer requirements and within the operational conditions, so that ongoing operating costs can be significantly reduced. Temperature...

...Our quality SANHA ball valves are made of brass CW 617N and can be delivered in a multitude of versions such as with threaded and press ends, or in the dimensions 15-54 mm, 16-26 mm and ½" to 2". The ball valves can be easily and quickly combined with all SANHA systems, thus providing a real alternative to conventional products. With SANHA ball-stop valves we provide our customers with the oppurtunity for an optimal safe and at the same time very economical solution for the installation of machinary, equipment or other facilities such as risers.

...The evaporation capacity is up to approximately 300 kg/h, depending on operating conditions. Built on a skid and transportable by truck. Design: Evaporation crystallizer with external heating element and recirculation system, as well as a vacuum system consisting of 2 surface condensers, a steam ejector, and a vacuum pump. Standalone small control system, touch control panel, control cabinet, measuring instruments, control valves, wiring, etc.

... decouple the heating or cooling circuit from the consumer circuit, as the flow rate in the heating/cooling and system circuits is not constant. The number of operational heat or cold generators and the position of the control devices in the consumer circuits (thermostatic and other valves) affect the flow rate of the entire system.

... maximum overpressure (safety valve) 179 °C steam temperature (boiler) Fully automatic refilling approx. 3.5 L water capacity (total) 15 bar high-performance pump Stainless steel heating boiler 155 cm stainless steel heating hose 2 solenoid valves Automatic pressure regulator 2 safety temperature monitors 1 additional overpressure valve 5 volts at the handle Control at the handle...

...KFE ball valves are available for drinking water or heating and can be used in various applications. They are used for filling and draining closed systems, such as a drinking water or heating circuit, or for emptying storage tanks. A closed system in a heating or drinking water installation should always be completely drainable. For this purpose, KFE ball valves can be installed at the lowest...

... recirculation system equipped with European pumps and valves for a better performance Sight glass Viewing ports Double jacket Compact design Homogenizer with pump functionality. Blades designed to mix and knead. CIP system Steam system Vacuum pump Agitator with high tech anchor design Automatic open and closing system HMI and PLC with SCADA system Available certification up on your request: UL, CE, cGMP, FDA, ASME. Available documents up on your request: I.Q (Installation qualification), O.Q Operational qualification), P.Q Performance qualification.

... made of elastomer (rubber and plastic) • Stainless steel corrugated pipes and hoses • Pre-insulated solar hose • CATS® - assembly system • other assembly systems Media: • Combustion gas • Technical gases • Oxygen • Drinking water You will find our products and assemblies in: • Heat exchangers • Medical applications • Respiratory protection • Renewable energy • Solar systems • Heating and cooling applications • HVAC • District heating • Automotive • Building technology • Chemical industry • Trace heating • Safety technology • Home installation (water and gas) - CATS® self-assembly system...

KFM primarily focuses on control engineering tasks in industrial heating and process technology across almost all sectors and in shipbuilding. Both electronic controllers and control valves are supplied, so that the entire control system can be obtained from a single source if needed, including qualified control engineering consulting upon request. Particular expertise and areas of focus lie in...

...combustion system, as well as control and safety devices. The installation, commissioning, and dismantling of the boilers are carried out by our foremen. We require that the necessary auxiliary personnel are provided on-site, the piping connections are made, and the boilers are operated with weather protection. Complete container systems are also available. Operation, maintenance, insurance, and TÜV approval are the responsibility of the renter and are not included in the rental price. However, if needed, we can also provide an offer for a combined transport, installation, and machinery insurance.

...electrical engineering, and electronics. The company provides various system solutions in the areas of steam, water, and cooling. The product portfolio includes, among others, the following product areas: Heat exchangers Control valves Jet pumps Drives Controllers Measuring technology Automation technology Accessories...

... is a partner of the automotive industry and its system suppliers, as well as the household appliance industry. As a carrier of know-how, DC guarantees solutions even for demanding specifications and is a dedicated specialist in new technologies in climate control and innovative applications. Components for automotive air conditioning: pressure switches, expansion valves, dryers. Components for 'White Goods': hinges for ovens, microwave devices. Components for gas heating: control panels, electronics, valves, aftermarket: batteries, spare parts for air conditioning systems.