environmental simulation

... such as salty lift (salt fog). As an environmental simulation laboratory, we simulate these environmental conditions in our climatic chambers and climatic chambers, creating real conditions to investigate the long-term behavior of the test specimens in reality. Environmental simulation and thermal shock testing laboratory for electronic assemblies and printed circuit boards We specialize in performing environmental simulation and temperature shock testing of electronic and mechanical assemblies. With over ten years of experience with the requirements of the automotive industry and medical ...

...In addition to the usual ICT/FCT procedures, we can also specifically verify each individual manufacturing step depending on the requirements. Efficient testing strategies and final functional tests are an integral part of our quality management. In our testing laboratory, we can conduct automated, static, and cyclic environmental simulations for you, ranging from temperature shock air and temperature shock liquid tests to storage temperature tests and humidity tests. Based on the future operating environment, we compile a suitable qualification program for each product.

...Liebisch Corrosion Testing Device / Salt Spray Fog Device as Tabletop Units - Liebisch Corrosion Testing Device / Salt Spray Fog Device as Tabletop Units for environmental simulation are available in designs with a chamber volume of 300 liters. Constamatic® S 300 A-TI For conducting salt spray tests according to national and international standards such as: - DIN EN ISO 9227 (formerly DIN 50021...

...As your reliable partner in environmental simulation and testing, we support you in all necessary process steps. You benefit from over 10 years of experience. - Sizing and setup of test facilities - Implementation of testing procedures - Testing of active specimens - Mechanical and electrical testing - Insulation resistance and breakdown strength measurement - Data collection and evaluation - And much more.

...Artificial weathering (sun simulation) results in an increased acceleration factor and better reproducibility compared to outdoor weathering. Especially for larger test specimens, the testing procedure according to DIN 75 220 has proven effective in practice. The necessary number of light sources is determined based on the desired irradiation area. In combination with a filter glass plate, the light spectrum corresponds to the global radiation CIE 85 Table 4. This allows potential weaknesses to be identified and optimizations to be implemented even during the development phase.

... whether they be small or walk-in, chambers used in component/ small product testing or drive-in chambers for complete vehicle testing, even up to extra large systems for trains, trucks and aircrafts. Superior Solar Simulation with SolarConstant A key to the success of solar environmental testing is the quality of the solar simulation itself. A close spectral match to natural sunlight is critical...

...We manufacture cold and climate control systems for environmental simulation, professionally tailored to your needs and requirements, such as snow generation, ice formation, wind tunnel simulation, etc.

...In our modernly equipped environmental simulation laboratory, we conduct tests according to international standards and OEM specifications.

We are a subsidiary of CTS Clima Temperatursysteme GmbH from Germany and are responsible not only for the Austrian market but also for the Slovenian market. With over 150 employees across Europe, our company group is one of the leading providers in environmental simulation. The rapid growth of the company, founded in 1995, is primarily due to the high quality of our products. However, for long-la...

... outdoors or forms part of equipment that will be used in an environment where the ambient temperature is higher than in the UK, we can help. Some examples of tests are listed, but this is not an exhaustive list so please get in touch if you need to discuss your requirements: Water and Dust Ingress Salt Spray Shock and vibration Temperature and Humidity UV (Solar Radiation) simulation We are UKAS accredited for some environmental testing, giving manufacturers assurance of reliability, accuracy and consistency...

...The system is a self-sufficient unit and is made of a solid welded frame, contains media preparation, a hydraulic unit, and electrical engineering. The pressure test bench has a secure test chamber for burst pressure and hydrostatic pressure tests and, optionally, a climatic chamber for pressure tests with environmental simulation. Depending on the option selected, pressure change tests up to...

...Customized environmental simulation - GWP is your partner for questions regarding climatic, corrosive, and mechanical environmental influences on your products.

... diameters of up to 250mm are possible. In our prototype department, we are able to simulate or modify the environmental circumstances of the fan wheels or turbines, thus achieving optimal operational conditions. Furthermore, we carry out mould-flow analysis, use ANSYS from external partners for the flow simulation and establish the fault probability and fault effect with FPFEs. New: Development of blower systems and optimization of ventilation systems.

... measurement include: + Measurement of sound emissions from existing systems + Professional evaluation of the sound situation + Sound prediction calculations for new components + Soundproofing design for individual components and the overall system + CFD flow simulation for optimizing flow management + Specific sound measurements and environmental analysis + Volume flow measurements...

...Development and construction of test systems for environmental simulation, i.e. climate and temperature tests as well as corrosion tests (e.g. MEMS testing and automotive durability tests on tilt sensors, inclination sensors, inertial sensors, inclination sensors, automotive parts and many more). - Adjustable humidity - Typical temperature ranges are -72 to + 120°C - Parallel testing and...

...with adjustable humidity and temperature to simulate the environmental conditions of a test specimen (e.g. household appliances, heating technology) The basis is a standard or climatic chamber (e.g. test kitchen, environmental simulation) with adjustable air humidity and temperature. On the basis of decades of experience in automotive test engineering, EP-E developed a concept in which the air...

...In addition to FEM calculations, we offer topology optimization, crash simulation, flow and vibration analysis, as well as operating load and force determination.

... (Laboratory 0604) and thermal fluid component testing services to a wide scope of industries whilst maintaining a reputation for quality, cost effectiveness, impartiality and reliability. Our specialist UKAS accreditation offerings for aviation, automotive, medical, environmental and pharmaceutical sectors provide worldwide acceptance for many of the ASTM, EPA, ISO, BSI, DIN and SAE standardized test protocols.

... water treatment plant. Thanks to laboratory tests or dynamic simulation with tools like "WEST" or "BioWin", we optimize water treatment systems, increasing their performance and reducing pollution. Additionally, we provide recommendations on the integration of advanced technologies in secondary or tertiary treatments. We also conduct a complete analysis of costs, regulatory compliance, environmental impact, and current legislation, ensuring a more efficient, sustainable, and low-maintenance system.

...Electrical products must not only function safely under optimal external conditions but also when extreme circumstances prevail. The VDE Institute supports this with environmental testing.

... product lifecycle in fast motion and can provide insights into potential failures. We conduct mechanical-dynamic environmental tests (vibration, shock, impact, drop, etc.), climate tests (e.g., 2-chamber temperature shock procedures, humidity storage), IP protection class tests, vacuum tests, tests for resistance to chemical influences, as well as endurance tests and life-cycle tests. Feel free to ask us about the various testing options.

...Thermostatic and Climatic Chambers, Galli’s Original Equipments, for environmental simulation tests. Suitable for automotive, aeronautical, electronic, optical, semiconductor, biological, chemical and pharmaceutical industry. Ideal for environmental simulation testing, Genviro Climatic and Thermostatic Chambers provide the solution to your need to meet increasingly stringent International and...

...Projects are carried out within the design office or directly at our clients' sites, who are industrial players operating in high-tech environments with strong constraints (thermal, vibrational, environmental...). Our added value lies in our ability to offer fully customized solutions as we cover almost all fields of electronic systems design. Are you looking for a partner specialized in...

...The precise replication of real environmental conditions accelerates the research of new materials and enhances quality. Temperature and humidity, as well as the generation of extreme stresses, such as rapid temperature changes, vibration, corrosion effects, pollutants, light exposure, etc., can be reproducibly represented in Schlegel systems.

... and processed into syrup in a multiple effects evaporation installation. This syrup is then treated in the crystallization unit that generates sugar and allows concentrating the remaining impurities in the molasses. DSEC’s simulation program is of paramount importance at this stage so as to define the most efficient energy set-up as well as to precisely size any single equipment of the line.

...Used for detecting corrosion protection failures of samples in humid environmental climates. Stress testing of specimens in condensate - constant climates or condensate - alternating climates according to DIN EN ISO 6270-2 CH, AHT, AT (formerly DIN 50017 KK, KFW, KTW) Condensate testing with harmful gases. Simulation of industrial atmosphere in condensate alternating climate with SO2 according...

...Complete EMC testing and environmental simulation for type approval in shipbuilding - all from a single source...

... testing technology, supporting you from the product idea to market launch. To achieve this, we combine our expertise in optics, mechanics, and electronics, offering consulting and tailored solutions for our customers according to product-specific requirements. - Calibration and test equipment management - Precision measurement and sample testing - Materials technology - Device safety - Electromagnetic compatibility (EMC testing) - Environmental simulation: climate, vibration, shock - Chemical auxiliary and operating materials...

...We produce cooling and freezing cells in all desired dimensions and designs. Through our customized planning and production specialized in special dimensions, we can respond very flexibly to your specific requirements. You benefit from our many years of experience in environmental simulation and custom cell construction. Our Solutions Cooling and freezing cells for individual requirements...

... program. All agricultural machinery chains from iwis agrisystems undergo extensive testing in the laboratories, test stands, and simulation facilities of the iwis manufacturing sites to ensure consistently high reliability and quality even under extreme environmental conditions. Together with machine manufacturers, tailored drive solutions are developed, tested, and brought to series production in our agricultural machinery center in Sontra.