NSGATE - Supplier of industrial networking products for outdoor Video Surveillance Systems

The compact Fan Heater prevents the formation of condensation and provides an evenly distributed interior air temperature in electrical enclosures. It has clip for DIN Rail or Door mounting. The heating element is made on the basis of a self-regulating heating cable. The temperature of the heating element does not exceed 65°C, which ensures maximum safety and energy efficiency. The original design of the cable fastening does not allow its individual turns to touch each other, which allows maintaining the maximum heat transfer. The heater and fan are connected to the electrical circuit using two screw terminals. It is possible to separate the power circuits of the heater and the fan and use the fan together with the heater or separately in the cooling / ventilation modes of the enclosure. The NSBon-18 is suitable for the most types of junction boxes and electrical enclosures.

NSBon-36 is used to protect user's equipment installed into NSBox Access Node or NSB/NSE/NSP electrical enclosure with climatic control system inside from damage that can be caused by system start in low temperature conditions. The idea is not to apply power to the equipment before temperature inside the cabinet reaches acceptable level. I.e. if the temperature is lower than required by protected device's datasheet and power is applied to the entire Access node or Enclosure, the heater starts first and only after temperature rises above level set by user power is applied to the protected device. NSBon-36 consists of normally open thermostat with adjustable threshold, a contactor that is used to apply power to the user's equipment under protection and terminal blocks.

Thermoelectric Coolers or Thermoelectric Assemblies are designed to remove heat around critical components within an electrical enclosure with IP66 / NEMA4 protection category. These is a thermoelectric module (thermoelectric air conditioner) using the Peltier effect. The thermoelectric modules create a temperature difference between the internal and ambient heat sinks. It makes internal air colder while heat is dissipating into the external environment. Fans help the transfer of heating from the heat sinks. The main advantages of Thermoelectric Cooler over conventional compressor are: it can be controlled electronically; it is easily reversible when the current is reversed; it can work in harsh environments: in high ambient temperatures or heavily polluted ambient air; in application with vibrations or strong accelerations. Thermoelectric Coolers should be used in regions with hot climates, to extend the service life of UPS batteries

The NSBon-47 is a compact and cost effective Active PoE (48VDC) to Passive PoE (24VDC) converter. The input can accept any PoE that meets IEEE802.3af/at/bt standards from regular switches or injectors. The output is 24VDC Passive PoE up to 24W. Incorporating a compact, in-line design, they are perfect for outdoor use inside a weatherproof electrical enclosure. NSBon-47 can be connected to any PoE port of Industrial switch located inside outdoor access Node NSBox by RJ45 male connector. It is compatible with auto-sensing and is recognized by PoE switch as a 802.3at/af PD device. On the other side of the converter there is an RJ45 Female connector for connecting various devices powered 24VDC Passive PoE ranging from video camera, access point, and router (Ubiquiti UniFi, airMAX etc.). Pins 4,5 and 7,8 of the RJ45 Female connector are used for powering in PoE mode B. Maximum output power is 24W. NSBon-47 compatible with all 24VDC Passive PoE devices.

NSBon-49 is a high-efficiency isolated DC-DC converter with ultra-wide input voltage range and 12 or 24 VDC output. The most important application of this power converter is powering user's equipment that requires 12 or 24 VDC power and must be installed into outdoor access node or uninterruptable power supply cabinet with single 48V DC UPS system inside. 48VDC UPS is the most used UPS for outdoor access nodes because 48VDC power is required by most PoE switches. Therefore NSBon-49 power converter allows to install devices with different power requirements into the outdoor cabinet with single 48 VDC UPS system and helps to save space and solution cost. NSBon-49 can be used for powering LTE/4G routers, NVR's, access controllers, sensors etc. NSBon-49 has input under-voltage protection, output short-circuit, over-voltage and over-current protection. So using NSBon-49 power converter together with 48VDC UPS allows to provide uninterruptable power supply to 48V PoE switches and 12/24V

NSBon-59 is a multiband GSM 900/1800 | 4G LTE/ 3G/ WiMax | Wi-Fi antenna suitable for outdoor installation. It is made of UV resistant ABS plastic and can be used together with NSGate NSBox-LTE Outdoor Access Nodes equipped with wireless data transmission devices (4G/LTE routers etc.). NSBon-59 Antenna provides much better bandwidth comparing to antenna installed inside the made of steel cabinet. Steel cabinet walls of a NSBox Access node causes signals to reflect and poor penetration as a result. Therefore, using remote NSBon-59 Antenna is a good solution to achieve stable bandwidth and performance. In order to get better performance, avoid mounting the antenna next to a column or vertical support that could create a shadow zone and reduce the coverage area.

NSBon-63 4G LTE Cellular Router is highly reliable and secure wireless communications gateway designed for industrial networking. It supports multi-band connectivity including FDD/TDD LTE, WCDMA and GSM for a wide range of applications, such as Industrial IoT, outdoor Video Surveillance Systems and vertical M2M markets. To enhance reliability, NSBon-63 is equipped with dual SIM that supports failover and roaming over to ensure uninterrupted connectivity for mission-critical communications. With flexible LAN/WAN Ethernet options, NSBon-63 allow you to customize your professional applications in diverse environments. It also provides enterprise-grade software features, such as QoS, DMZ, VLAN, OSPF, BGP, RIP-1/2, DDNS, and etc. Featuring VPN Tunnels, Firewall, TR069, and SNMP Trap, NSBon-63 enhance highly secure authentication, encryption and management to protect your data efficiently between public and private networking.

The NSBon-01 mounting kit is designed for quick and reliable mounting of the NSB-xxyy | NSP-xxyy | NSV-xxyy | NSE-xxyy series electrical enclosures on circular or rectangular poles. The components of the mounting kit are made of zinc-plated sheet steel and stainless steel. There are two options of lengths of clamping straps, for standard diameter poles up to 190 mm and enlarged diameter up to 300 mm. In the equipment of NSBon-01 includes two mounting rails, two clamping straps, four clamping brackets and the accessories. The pole mounting kit, by default, is designed for 600 mm wide electrical enclosures. By cutting the rail to length or drilling additional holes on the cabinet, the NSBon-01 mounting kit may also be fitted to larger and smaller electrical enclosures.

NSBon-04 is a plastic handle with lock system. It is designed to lock an electrical enclosure using a unique lock system and reliable protection against acts of vandalism. In the equipment includes a plastic handle with lock cylinder insert, a lock No. 3524E and two keys. The installation of the NSBon-04 option is quick and easy without any mechanical modification of the door.

The indoor lighting kit NSBon-06 is suitable for the most types of junction boxes and enclosures. The kit allows to execute repair electrical works (replacement of an Ethernet switch, power supply, batteries) on the installed facility at any time of the day. The system is equipped with a separate circuit breaker. For safe work, you should turn off the main power of the enclosure and all equipment. By default, the lamps are installed in the niches of the top and bottom walls of the cabinet. If necessary, it can be moved to another location. The kit consists of the following components: One or two LED lamps in metal frame with a reflector Magnets for mounting the lamp to a metal surface Circuit breaker and set of wires