Results for
JSC SAKCABLE (SAKCABLE)
Georgia
For transmission and distribution of electric power at stationary devices with rated voltage 0,660kV and 1 kV frequency 50Hz. For stretching in the air where there is no danger of mechanical damage of the cable, also for laying into channels without influence of stretching forces. While laying the cables in a single layer, they are flame retardantThe copper cores with section 2,5-25mm2 inclusive are produced of single wire of 1 class flexibility, accorgind to gost standard 22483-2012. Number of cores in the cable 2,3.in case of supply in bundles the construction length is agreed with the customer. On wooden drum no less than 450m. One batch can contain no more than 20% of cable length not less than 50m.
Request for a quoteQUELLTECH GMBH
Germany
Testing requirements for a manufacturer in electronics industries had changed: For an assembly included in a smartphone, the absence of contact between speaker ultra fine wires and adjacent components is essential. Fulfillment of this condition, until now only subjected random sampling by microscopy, from now on has to be verified in a 100% procedure. Due to labor cost, microscopy for this amount of inspection is no more lucrative. Detection of ultra fine wires in electronic device The particular challenge The fine wires made of copper in smartphone speakers dispose of a high reflection and only a small diameter. The QuellTech Solution A high-resolution QuellTech 2D/3D Q4-5 Laser, featuring a particularly adapted laser wavelength and an ultrafine laser line in the corresponding installation, is combined with a linear axis equipped with a convenient encoder output. Due to its special chip analysis, the Quelltech sensor delivers a stable and highly reproducible signal on the fine wires
Request for a quoteVERCO ELECTRO COMPONENTS
Belgium
Hubbell offer very secure connection systems for hight and medium current. Switching boxes for hight and medium loads and currents. The connection materials from HUBBELL wiring-Devices are matching the safety standarts of NEMA and OSHA. The connection system is covering a wide range of connectors, You do have the STRAIGHT BLADE range of connectors as the Safety TWIST-LOCK as a HUBBELL-LOCK range and a Circuit-lock. The classification of the connectors is done regarding the load and the current they can carry and the polarization is depending from those features. some connectors can carry up to 600 Amp
Request for a quoteVERCO ELECTRO COMPONENTS
Belgium
Stainless steel maine connectors from HUBBELL suit all marine purposes. Shore side Power Inlets Boat side Power Outlets Moulded cable assemblies,various lenght. Carrying up to 100 Amp Very resistant mechanical and electrical propreties. Data communication connectors USB, and TV plugs can be integrated. Approvals and widely used over the all world in the harbours.
Request for a quotePERGEL METAL
Turkey
Today, electrical and wired devices are the most needed products. Computers, televisions, internet, chargers or many machines are used wired. In order for the cables to have a long service life and be used without problems, they must be very well maintained. For this, there are also cable regulators. These regulators prevent and protect the cable from damage. In this way, there are no situations such as breaking, breaking, crushing or bending. It is one of the most preferred materials.
Request for a quoteBURSTER PRÄZISIONSMESSTECHNIK GMBH & CO KG
Germany
The RESISTOMAT® model 2320 is a universally applicable and easy to operate measurement device for low-ohmic resistances. The light and handy device in a stable IP54 plastic housing with membrane keypad is likewise suitable for use in service, laboratory or on the production floor. The power supply is done via built-in rechargeable battery packs or by standard batteries. If need be, the temperature of samples can be measured and the sample resistance is subsequently compensated to fit the value at 20°C. This applies for samples with resistances depending on the sample’s temperature. The temperature coefficients for copper and aluminium are included as standard. A third and fourth coefficient may be set individually for any given material to be measured. Features: — Measuring ranges from 40 mΩ to 4 kΩ — Resolution up to 10 μΩ — Measuring accuracy 0.05 % Rdg. — Autorange — Temperature compensation — Bipolar measurement — Input voltage protection up to 415 Vrms
Request for a quoteKW HYDRAULIK GMBH
Germany
Bus Bar Working Stations for Bus Bars and Flat Material Punching Tools for Bus Bars and Flat Material Cutting Tools for Bus Bars and Flat Material Bending Tools for Bus Bars and Flat Material Brochure Tools for Control and Switchgear Cabinets Tools for Laminated and Flexible Bars and Earthground Sheet Metall Hole Puncher DIN Mounting Rail Cutting Devices Wiring Duct Cutting Tool Punching Tools for Sheat Metall
Request for a quoteBS BODENSTECKDOSEN SYSTEMTECHNIK GMBH
Germany
Retractable Power Distributor/power bollard SV501 for indoor and outdoor use, made of saltwater-resistant aluminum. Due to its solid construction, the SV501 lowering distributor can be driven over by a truck, of course, only when the lid is fully closed. The surface is anodized with a stainless steel look. The retractable power distributor SV501 is equipped with 8 protective contact sockets 2 / 16A 230V with hinged cover (unsecured, without wiring). The devices are raised and lowered using a crank. Drainage is required for outdoor installation. The housing is watertight when closed, protection class IP67. Alternatively, other combinations are also possible. Further equipment variants and colors on request.
Request for a quotePEEKCHINA CO., LTD.
China
PEEK (Polyether Ether Ketone) heat shrink tubing is revolutionizing the medical device industry with its exceptional properties and reliable performance. Known for its high-temperature resistance, chemical resistance, and mechanical strength, PEEK heat shrink tubing provides unparalleled protection and insulation for sensitive medical equipment. Whether it's ensuring the durability of surgical instruments or protecting the intricate wiring of diagnostic devices, PEEK tubing is the ideal choice for enhancing the safety, efficiency, and longevity of medical devices. Its low flammability and excellent electrical insulation further contribute to its suitability in critical healthcare applications, making it an essential component for medical device manufacturers seeking high-performance solutions.
Request for a quoteEC PLAZA
South Korea
Universal Testing Machine is a representative test equipment for physical properties. It is capable of measuring load, strength, elongation of products or materials such as rubber, film, plastic, metal, etc. - Frame Load Capacity (Max.) : 5kN - Main Load Cell : 5kN - Load Range : 50 (kgf) ◀(Up to 4-step conversion) - Column Type : Single Column - Load Accurancy : Less than ±0.5% - Crosshead Speed Range : 0.01 ~ 500mm/min - Load Resolution : 1/50,000 - Machine Controller : Touch Type Servo Controller(Position Control Type) - Test Category : Tensile, Tear, Peel, Compression, Bending, Repeat, etc. - Dimensions : 478× 650× 1375(H), 82kg - Main Power : AC 220V 2P, 50/60 - It is single column model that can be tested under 5kN. - UNITEST M1 is widely used for testing materials such as films, rubber, fibers, medical devices, biomaterial, and wires etc. - The main feature of the UNITEST M1 is that it requires a small footprint
Request for a quoteBASAK LAZER
Turkey
Argon welding is the word “Tungsten Inert Gas” that gives the welding method its name. Welding is also called the initials of this word and is referred to as TIG welding. The heat to perform the welding process is generated between the electrodes made of tungsten metal, which has a very high melting point, and the parts to be welded. The welding zone is protected by argon or helium gas sent from a nozzle surrounding the electrode. The electrodes used in the Tig (argon) welding method allow to join the welded material by melting, without melting themselves. When deemed necessary, additional welding rods are delivered to the welding area by the welder or by automatic wire feeding devices, as in oxy gas welding. Argon gas is generally used as a shield in argon welding. Argon gas is a noble gas, so it does not react and provides strong protection. It optimizes the ignition characteristics and stability of the arc
Request for a quoteXIAMEN INNOVACERA ADVANCED MATERIALS CO., LTD
China
Innovacera manufactures many kinds of metalized ceramic coil bodies for electrical inductors, including the H-shapes, U shape and Bone-shaped and so on. The main material of metalized ceramic coil bodies is 96 Alumina and the metallized coating material is W, Ni, Au etc. Our factory have more than 20 years of metalized ceramics producing experiences, can give a prompt solution for R&D project. The metalized bodies is partially metalized , ceramic inductor coil bodies cores can make very small size which it is big helpful for the electrical systems , wire-winding technique, electronics devices and electrical coils components miniaturization developed.
Request for a quoteSCHNELL SPA
Italy
Stirrup bender and bar shaping machine from coil with 2 bending heads for the production of stirrups and shaped wires with bends at both ends using wires up to Ø 20 mm (#6). Driven by electric servomotors. These automatic stirrup benders and bar shaping machines are equipped with Max. pulling speed 140 m/min (460 ft/min) Straighteners (horizontalvertical) with electronic and independent setting for the 2 wires with Joystick AntiTwist electronic device (Optional) Patented feed unit that allows independent advancement for single o double wire (Optional) 2 bending unit (upper and lower) Pulling with 4 motors and 4 pulling drive wheels Cutting unit with adjustable wire guide, reversible mobile and fixed cutting blades Web Teleassistance Prestraightening Feeding Unit (Optional) Automatic motorized wire change (Optional) 3D version for the production of tridimensional pieces.
Request for a quoteSCHNELL SPA
Italy
Stirrup bender and bar shaping machine from coil with 2 bending heads for the production of stirrups and shaped wires with bends at both ends using wires up to Ø 16 mm (#5). Driven by electric servomotors. Also available HS version machine. These automatic stirrup benders and bar shaping machines are equipped with Max. pulling speed 140 m/min (460 ft/min) HS Version 200 m/min (660 ft/min) Straighteners (horizontalvertical) with electronic and independent setting for the 2 wires with Joystick AntiTwist electronic device (Optional) Patented feed unit that allows independent advancement for single o double wire (Optional) 2 bending unit (upper and lower) 4 pulling drive wheels Cutting unit with adjustable wire guide, reversible mobile and fixed cutting blades Web Teleassistance 3D version for the production of tridimensional pieces.
Request for a quoteSCHNELL SPA
Italy
Bidirectional automatic stirrup bender from coil for the production of stirrups and cuttosize bars using wires up to Ø 20 mm (#6). Driven by digital electric servomotors. Coil 20 automatic stirrup benders are equipped with Max. pulling speed 140 m/min (460 ft/min) Straighteners (horizontalsverticals) with electronic and independent adjustment for the 2 wires with Joystick AntiTwist electronic device (Optional) Pulling with 4 motors and 4 pulling drive wheels Cutting unit with adjustable wire guide, reversible mobile and fixed cutting blades Web Teleassistance
Request for a quoteSCHNELL SPA
Italy
Bidirectional automatic stirrup bender from coil with disk bending system for the production of stirrups and cuttosize bars using wires up to Ø 14 mm (#4). Driven by electric servomotors. Formula Disk automatic stirrup benders are equipped with Max. pulling speed 200 m/min (660 ft/min); Straighteners (horizontalsverticals) with electronic adjustment and independent position for the 2 wires with Joystick; AntiTwist device (Optional); Cutting with Brushless motors; Web Teleassistance.
Request for a quoteSCHNELL SPA
Italy
Bidirectional automatic stirrup bender from coil for the production of stirrups and cuttosize bars using wires up to Ø 14 mm (#4). Driven by digital electric servomotors. Formula 14 stirrup benders are equipped with Max. pulling speed 150 m/min (500 ft/min) Straighteners (horizontalsverticals) with electronic adjustment and independent position for the 2 wires with Joystick AntiTwist device (Optional) Cutting with Brushless motors Web Teleassistance
Request for a quoteDo you sell or make similar products?
Sign up to europages and have your products listed
ORBITEC GMBH
Germany
The RBK 60 S is an extremely robust water-cooled weld head for a standard heat exchanger application up to an ID of 60 mm, modified to an ID of 99 mm or 120 mm. The head is pneumatically centred and is available with a rotating wire device and/ or arc voltage control (AVC) as an option. The head can also be used with a pneumatic positioner instead of a balancer. Versions: — RBK 60 S weld head with pneumatic centring, including hose package, 8m, water-cooled — RBK 60 S weld head with pneumatic centring and wire feeder incl. hose package, 8m, water-cooled — RBK 60 S weld head with pneumatic centring, wire feeder and AVC incl. hose package, 8m, water-cooled Package includes: — Weld head — Small torch incl. torch consumables and tungsten electrode Ø 2.4 mm — Water-cooled hose package, 8 m — Pull bar B — Transport case Optional: — Div. spring sleeves and pull bar sets for RBK 60 S — Torches, Balancer, Tube-to-tubesheet positioner...
Request for a quoteLEVTECH SERVICE & PRODUCTION SRL
Romania
The LSP-TSTS is a slim design easy to use temperature transmitter for Pt100/Pt1000 3 wire or 2 wire temperature sensor. This device provides a linearised 4-20mA signal output, proportional to the temperature characteristic of the Pt100 or Pt1000 sensor. Temperature range can be changed on request before order (Default -15 to 150ºC). Features • RTD type Pt100 or Pt1000 Input • 4 to 20 mA linearised output on current loop or 0-10V • TS-35 DIN rail mounting • +/-0.1% accuracy • Ip40 case • Screw terminals • Easy to use • Supply from current loop
Request for a quoteKSK DEVELOPMENTS SP. Z O.O.
Poland
The measuring probe lance is in the form of a length of 2000 mm and includes the three temperature sensors: - on the tip of the lance - at a distance of 750 mm from the tip and - at a distance of 500 mm from the end of the lance The lance tip has a rounded head, so when pushing into the pile it does not poke through encountered "in the way" compost components. The probe in wireless version is powered by a battery. Measurements and data are transmitted, depending on the version of the device, by wire or wireless.
Request for a quoteKSK DEVELOPMENTS SP. Z O.O.
Poland
The measuring probe is in the form of a lance 1000 mm long and contains an oxygen sensor. The end of the lance driven into the compost has a rounded head, so that the compost components encountered "on the way" do not stick into it. The probe is powered by direct current with a rated voltage of 12VDC or 24VDC, while the data on measurements are transmitted, depending on the version of the device, by wired or wireless. The oxygen probe in the version with wireless data transmission can be equipped with two network interfaces depending on the demand. In the wired version, the data signal is realized in the analog 4-20mA or digital form via the CAN bus. The second solution is to transfer data directly to the cloud via the LoRa network. This type of transmission allows you to cover a huge area with a radius of several kilometers in a star topology with one base station or through the public network.
Request for a quoteKÖSTER & CO. GMBH
Germany
The model K 26 is a robust stud welding gun, especially for studs ø 22 – 25 mm Ideal for welding shear connectors SD 25 mm Ideal for through-deck-welding td Most suitable for long shear studs Adjustable hydraulic plunge damper Standard support with 3 legs Body: fibre-glass reinforced polyamide Lifting ring system with length compensation up to 8mm Control cable plug (4 wire) Optimal Integrated shielding gas device
Request for a quoteKÖSTER & CO. GMBH
Germany
The model SK15 is a robust stud welding gun, designed for welding of threaded studs with ceramic ferrules ø 4 - 12 mm Ideal for short cylce stud welding ø 3 - 12 mm Best for stud welding using shielding gas ø 3 – 12 mm Lifting range 1 – 4,5 mm Standard support with 2 legs High repeatability Body made of fibre-glass reinforced polyamide Control cable plug (4 wire) Optional Integrated shielding gas device
Request for a quoteENDRESS+HAUSER AG
Switzerland
Promag H is the preferred sensor for applications with highest requirements in the food and beverage and life science industries. Promag H 200 offers in addition genuine, industry-compliant two-wire technology. This enables the device to be seamlessly integrated into existing infrastructures and control systems. Additional advantages are high operational safety in hazardous areas thanks to an intrinsically safe design (Ex ia), and a familiar installation procedure.
Request for a quoteHALSTRUP-WALCHER GMBH
Germany
This pressure transmitter is particularly well suited for monitoring filters and pressures in HVAC (heating, ventilation and air conditioning) applications. DIP switches allow users to configure the output signal and switchable measurement ranges (optional). Settings provide an option for conversion to a root-extracted output signal (displayed as a % of the maximum output value). An internal button is also available for performing a zero-point correction or fine-tuning the end value. An optional display allows users to read the measured value directly on site in Pa or kPa. With an optional time constant (up to 10s), the instrument can produce an attenuated output signal, even under unstable pressure conditions. An optional two-wire version of the device is also available for reducing wiring complexity. In addition to simple wall-mounting with just 2 screws, the PS 17 is also suitable for mounting on top-hat rails.
Request for a quoteENDRESS+HAUSER AG
Switzerland
Promag P 200 offers genuine, industry-compliant two-wire technology. This enables the device to be seamlessly integrated into existing infrastructures and control systems. Additional advantages are high operational safety in hazardous areas thanks to an intrinsically safe design, and a familiar installation procedure. Promag P 200 is dedicated for chemical and process applications with corrosive liquids and high medium temperatures.
Request for a quoteSTRECKFUSS SYSTEMS GMBH & CO. KG
Germany
TYP C 060 Cutting and forming Device for jumper wires Description The Streckfuss model C060 is designed to cut and form 20 to 22 gauge jumper wires. The machine has an adjustable center to center distance and uses interchangeable die sets to vary the cut length. The wire straightener, feed clamp and backlash assembly combined with an adjustable feed stroke produce a precise jumper wire every time. Components
Request for a quoteROUND SOLUTIONS GMBH & CO. KG
Germany
The Round Solutions PingPong is an embedded IoT/M2M hardware platform made for Software Developers. The platform supports extension boards that add unlimited capabilities. It can be used to easily make physical devices that connect to the web. It's literally plug, push and play. PingPong comes with both wired and wireless connectivity. The device is available in two open-source SW versions. While the RTOS version comes with the world's fastest 32-bit microcontroller running in C/C++, the Linux version uses the powerful ARM Cortex processor for even more functionality and applications. PingPong base circuit boards also have a high speed Telit cellular module, a high accuracy positioning component for the Global Navigation Satellite System (GNSS), Ethernet, USB, CANBUS among other items. The Evaluation Kit comes with a dedicated M2M/IoT SIM card and connectivity to a cloud platform.
Request for a quoteLABOM MESS- UND REGELTECHNIK GMBH
Germany
Features ■ Pressure transmitter with on-site indication for relative pressure measurements ■ Safety pattern gauge S3 per EN 837-1, NS 100 and 160 alternative high quality case with bajonet ring per EN 837-1 S1 ■ Nominal range 0…0.6 bar up to 1000 bar ■ Output signal: 4…20 mA (20…4 mA) 2-wire technology ■ Integrated angle-of-rotation sensor, not subject to wear ■ EAC declaration (upon request) Options ■ Approvals/Certificates - Calibration certificate - Explosion protection for gases and dust - Certificate of measuring equipment for Russian Federation - Material certificate as per EN 10204-3.1 ■ The electrical zero can be corrected by holding a ferromagnetic object to a marked location on the case ■ Additional switch function ■ Diaphragm seals see product group D5 ■ Output signal 0...20 mA and 0...10 V in 3-wire technology (for devices without Ex-protection and without zero point setting)
Request for a quoteResults for
Wire devices - Import exportNumber of results
34 ProductsCountries
Company type
Category